sehr langsame Kommandos zu den Rollos und nur sporadisch

malip · 22 Oktober 2019, 11:13:16

Hi,
habe alles schon lange am laufen und seit gestern wollten einige Rollos nicht mehr runter.
Das BUI ist etwas langsamer meine ich und einige Rollos haben nur Lust, wenn sie wollen.
Habe auch mal ein anderes Netzteil (Android quickcharge 2A) dran gesteckt (ist das stärgste, was ich sonst rumliegen habe im Haus), dann ist wenigstens die Spannungsmeldung weg.

Hier mit dem Netzteil, daß schon lange lief (steht nicht Raspberry drauf), mit dem Fehler:
[ 7.752586] Under-voltage detected! (0x00050005)

root@raspberrypi:/opt/fhem/FHEM# dmesg
[ 0.000000] Booting Linux on physical CPU 0xf00
[ 0.000000] Linux version 4.19.66-v7+ (dom@buildbot) (gcc version 4.9.3 (crosstool-NG crosstool-ng-1.22.0-88-g8460611)) #1253 SMP Thu Aug 15 11:49:46 BST 2019
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Raspberry Pi 2 Model B Rev 1.1
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] cma: Reserved 8 MiB at 0x37800000
[ 0.000000] On node 0 totalpages: 229376
[ 0.000000] Normal zone: 2016 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 229376 pages, LIFO batch:63
[ 0.000000] random: get_random_bytes called from start_kernel+0xac/0x4b4 with crng_init=0
[ 0.000000] percpu: Embedded 17 pages/cpu s39488 r8192 d21952 u69632
[ 0.000000] pcpu-alloc: s39488 r8192 d21952 u69632 alloc=17*4096
[ 0.000000] pcpu-alloc:

0
1
2
3
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 227360
[ 0.000000] Kernel command line: coherent_pool=1M bcm2708_fb.fbwidth=656 bcm2708_fb.fbheight=416 bcm2708_fb.fbswap=1 vc_mem.mem_base=0x3ec00000 vc_mem.mem_size=0x40000000 dwc_otg.lpm_enable=0 console=ttyAMA0,115200 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 elevator=deadline rootwait
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 886312K/917504K available (8192K kernel code, 629K rwdata, 2176K rodata, 1024K init, 821K bss, 23000K reserved, 8192K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xb8800000 - 0xff800000 (1136 MB)
lowmem : 0x80000000 - 0xb8000000 ( 896 MB)
modules : 0x7f000000 - 0x80000000 ( 16 MB)
.text : 0x(ptrval) - 0x(ptrval) (9184 kB)
.init : 0x(ptrval) - 0x(ptrval) (1024 kB)
.data : 0x(ptrval) - 0x(ptrval) ( 630 kB)
.bss : 0x(ptrval) - 0x(ptrval) ( 822 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] ftrace: allocating 26394 entries in 78 pages
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] arch_timer: cp15 timer(s) running at 19.20MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[ 0.000010] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[ 0.000031] Switching to timer-based delay loop, resolution 52ns
[ 0.000368] Console: colour dummy device 80x30
[ 0.001081] console [tty1] enabled
[ 0.001159] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[ 0.001214] pid_max: default: 32768 minimum: 301
[ 0.001665] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.001712] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.002983] CPU: Testing write buffer coherency: ok
[ 0.003695] CPU0: update cpu_capacity 1024
[ 0.003736] CPU0: thread -1, cpu 0, socket 15, mpidr 80000f00
[ 0.004780] Setting up static identity map for 0x100000 - 0x10003c
[ 0.005056] rcu: Hierarchical SRCU implementation.
[ 0.006278] smp: Bringing up secondary CPUs ...
[ 0.007611] CPU1: update cpu_capacity 1024
[ 0.007624] CPU1: thread -1, cpu 1, socket 15, mpidr 80000f01
[ 0.009075] CPU2: update cpu_capacity 1024
[ 0.009087] CPU2: thread -1, cpu 2, socket 15, mpidr 80000f02
[ 0.010527] CPU3: update cpu_capacity 1024
[ 0.010539] CPU3: thread -1, cpu 3, socket 15, mpidr 80000f03
[ 0.010718] smp: Brought up 1 node, 4 CPUs
[ 0.010878] SMP: Total of 4 processors activated (153.60 BogoMIPS).
[ 0.010906] CPU: All CPU(s) started in HYP mode.
[ 0.010931] CPU: Virtualization extensions available.
[ 0.012244] devtmpfs: initialized
[ 0.027758] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.028184] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.028250] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.029145] pinctrl core: initialized pinctrl subsystem
[ 0.030596] NET: Registered protocol family 16
[ 0.034156] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[ 0.041621] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.041676] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.041972] Serial: AMBA PL011 UART driver
[ 0.045014] bcm2835-mbox 3f00b880.mailbox: mailbox enabled
[ 0.090317] bcm2835-dma 3f007000.dma: DMA legacy API manager at (ptrval), dmachans=0x1
[ 0.092598] SCSI subsystem initialized
[ 0.092953] usbcore: registered new interface driver usbfs
[ 0.093055] usbcore: registered new interface driver hub
[ 0.093245] usbcore: registered new device driver usb
[ 0.110294] raspberrypi-firmware soc:firmware: Attached to firmware from 2019-08-15 12:06, variant start
[ 0.120560] raspberrypi-firmware soc:firmware: Firmware hash is 0e6daa5106dd4164474616408e0dc24f997ffcf3
[ 0.132332] clocksource: Switched to clocksource arch_sys_counter
[ 0.234088] VFS: Disk quotas dquot_6.6.0
[ 0.234240] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.234489] FS-Cache: Loaded
[ 0.234839] CacheFiles: Loaded
[ 0.249380] NET: Registered protocol family 2
[ 0.250500] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
[ 0.250584] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.250743] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.250956] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.251173] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.251267] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.251785] NET: Registered protocol family 1
[ 0.252785] RPC: Registered named UNIX socket transport module.
[ 0.252830] RPC: Registered udp transport module.
[ 0.252856] RPC: Registered tcp transport module.
[ 0.252882] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.255077] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[ 0.259237] Initialise system trusted keyrings
[ 0.259648] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[ 0.273224] FS-Cache: Netfs 'nfs' registered for caching
[ 0.274100] NFS: Registering the id_resolver key type
[ 0.274169] Key type id_resolver registered
[ 0.274196] Key type id_legacy registered
[ 0.274236] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.277510] Key type asymmetric registered
[ 0.277555] Asymmetric key parser 'x509' registered
[ 0.277662] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[ 0.277923] io scheduler noop registered
[ 0.277958] io scheduler deadline registered (default)
[ 0.278257] io scheduler cfq registered
[ 0.278292] io scheduler mq-deadline registered (default)
[ 0.278322] io scheduler kyber registered
[ 0.280798] bcm2708_fb soc:fb: FB found 1 display(s)
[ 0.291237] Console: switching to colour frame buffer device 82x26
[ 0.299113] bcm2708_fb soc:fb: Registered framebuffer for display 0, size 656x416
[ 0.307078] bcm2835-rng 3f104000.rng: hwrng registered
[ 0.310130] vc-mem: phys_addr:0x00000000 mem_base=0x3ec00000 mem_size:0x40000000(1024 MiB)
[ 0.316518] vc-sm: Videocore shared memory driver
[ 0.319755] gpiomem-bcm2835 3f200000.gpiomem: Initialised: Registers at 0x3f200000
[ 0.341487] brd: module loaded
[ 0.358758] loop: module loaded
[ 0.362460] Loading iSCSI transport class v2.0-870.
[ 0.366314] libphy: Fixed MDIO Bus: probed
[ 0.369202] usbcore: registered new interface driver lan78xx
[ 0.372002] usbcore: registered new interface driver smsc95xx
[ 0.374739] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[ 0.405379] dwc_otg 3f980000.usb: base=(ptrval)
[ 0.608445] Core Release: 2.80a
[ 0.611146] Setting default values for core params
[ 0.613972] Finished setting default values for core params
[ 0.817148] Using Buffer DMA mode
[ 0.819856] Periodic Transfer Interrupt Enhancement - disabled
[ 0.822627] Multiprocessor Interrupt Enhancement - disabled
[ 0.825318] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 0.827979] Dedicated Tx FIFOs mode
[ 0.831191] WARN::dwc_otg_hcd_init:1045: FIQ DMA bounce buffers: virt = b7914000 dma = 0xf7914000 len=9024
[ 0.836445] FIQ FSM acceleration enabled for :
Non-periodic Split Transactions
Periodic Split Transactions
High-Speed Isochronous Endpoints
Interrupt/Control Split Transaction hack enabled
[ 0.848793] dwc_otg: Microframe scheduler enabled
[ 0.848877] WARN::hcd_init_fiq:457: FIQ on core 1
[ 0.851407] WARN::hcd_init_fiq:458: FIQ ASM at 80654f4c length 36
[ 0.853916] WARN::hcd_init_fiq:497: MPHI regs_base at b8810000
[ 0.856484] dwc_otg 3f980000.usb: DWC OTG Controller
[ 0.859066] dwc_otg 3f980000.usb: new USB bus registered, assigned bus number 1
[ 0.861713] dwc_otg 3f980000.usb: irq 56, io mem 0x00000000
[ 0.864376] Init: Port Power? op_state=1
[ 0.866922] Init: Power Port (0)
[ 0.869745] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[ 0.874889] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.877625] usb usb1: Product: DWC OTG Controller
[ 0.880306] usb usb1: Manufacturer: Linux 4.19.66-v7+ dwc_otg_hcd
[ 0.883081] usb usb1: SerialNumber: 3f980000.usb
[ 0.886628] hub 1-0:1.0: USB hub found
[ 0.889242] hub 1-0:1.0: 1 port detected
[ 0.892557] dwc_otg: FIQ enabled
[ 0.892565] dwc_otg: NAK holdoff enabled
[ 0.892571] dwc_otg: FIQ split-transaction FSM enabled
[ 0.892586] Module dwc_common_port init
[ 0.892984] usbcore: registered new interface driver usb-storage
[ 0.895867] mousedev: PS/2 mouse device common for all mice
[ 0.899606] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer
[ 0.902672] bcm2835-cpufreq: min=600000 max=900000
[ 0.905935] sdhci: Secure Digital Host Controller Interface driver
[ 0.908673] sdhci: Copyright(c) Pierre Ossman
[ 0.911914] sdhost-bcm2835 3f202000.mmc: could not get clk, deferring probe
[ 0.915017] sdhci-pltfm: SDHCI platform and OF driver helper
[ 0.918733] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.921766] hidraw: raw HID events driver (C) Jiri Kosina
[ 0.924928] usbcore: registered new interface driver usbhid
[ 0.927815] usbhid: USB HID core driver
[ 0.931648] vchiq: vchiq_init_state: slot_zero = (ptrval), is_master = 0
[ 0.936584] [vc_sm_connected_init]: start
[ 0.945599] [vc_sm_connected_init]: end - returning 0
[ 0.949848] Initializing XFRM netlink socket
[ 0.952642] NET: Registered protocol family 17
[ 0.955464] Key type dns_resolver registered
[ 0.958512] Registering SWP/SWPB emulation handler
[ 0.962176] registered taskstats version 1
[ 0.964933] Loading compiled-in X.509 certificates
[ 0.976939] uart-pl011 3f201000.serial: cts_event_workaround enabled
[ 0.979831] 3f201000.serial: ttyAMA0 at MMIO 0x3f201000 (irq = 81, base_baud = 0) is a PL011 rev2
[ 1.984025] console [ttyAMA0] enabled
[ 1.993237] sdhost: log_buf @ (ptrval) (f7913000)
[ 2.047461] mmc0: sdhost-bcm2835 loaded - DMA enabled (>1)
[ 2.057405] of_cfs_init
[ 2.062650] of_cfs_init: OK
[ 2.068889] Waiting for root device /dev/mmcblk0p2...
[ 2.102519] Indeed it is in host mode hprt0 = 00021501
[ 2.177465] mmc0: host does not support reading read-only switch, assuming write-enable
[ 2.192840] mmc0: new high speed SDHC card at address 0001
[ 2.200618] random: fast init done
[ 2.208189] mmcblk0: mmc0:0001 00000 14.6 GiB
[ 2.218204] mmcblk0: p1 p2
[ 2.265057] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 2.278862] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[ 2.289505] devtmpfs: mounted
[ 2.301200] Freeing unused kernel memory: 1024K
[ 2.309025] Run /sbin/init as init process
[ 2.322395] usb 1-1: new high-speed USB device number 2 using dwc_otg
[ 2.331863] Indeed it is in host mode hprt0 = 00001101
[ 2.572814] usb 1-1: New USB device found, idVendor=0424, idProduct=9514, bcdDevice= 2.00
[ 2.586915] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.598145] hub 1-1:1.0: USB hub found
[ 2.605193] hub 1-1:1.0: 5 ports detected
[ 2.901534] systemd[1]: System time before build time, advancing clock.
[ 2.932408] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
[ 3.072935] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00, bcdDevice= 2.00
[ 3.083317] NET: Registered protocol family 10
[ 3.087550] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 3.096901] Segment Routing with IPv6
[ 3.115476] smsc95xx v1.0.6
[ 3.146687] random: systemd: uninitialized urandom read (16 bytes read)
[ 3.167876] random: systemd: uninitialized urandom read (16 bytes read)
[ 3.185845] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN)
[ 3.207523] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-3f980000.usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:dc:3d:55
[ 3.214240] systemd[1]: Detected architecture arm.
[ 3.251882] systemd[1]: Set hostname to <raspberrypi>.
[ 3.322510] usb 1-1.3: new full-speed USB device number 4 using dwc_otg
[ 3.338846] uart-pl011 3f201000.serial: no DMA platform data
[ 3.384216] random: systemd-gpt-aut: uninitialized urandom read (16 bytes read)
[ 3.480580] usb 1-1.3: New USB device found, idVendor=0403, idProduct=e0e8, bcdDevice= 2.00
[ 3.495334] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3.506007] usb 1-1.3: Product: ELV FHZ 1300 PC
[ 3.513762] usb 1-1.3: Manufacturer: ELV AG
[ 3.521115] usb 1-1.3: SerialNumber: EL3HRM96
[ 4.096460] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 4.113219] systemd[1]: Created slice System Slice.
[ 4.130222] systemd[1]: Mounting RPC Pipe File System...
[ 4.146109] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ 4.160062] systemd[1]: Reached target Swap.
[ 4.171928] systemd[1]: Listening on udev Control Socket.
[ 4.185230] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 4.448316] snd_bcm2835: module is from the staging directory, the quality is unknown, you have been warned.
[ 4.764276] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 4.924231] systemd-journald[119]: Received request to flush runtime journal from PID 1
[ 5.606827] vc_sm_cma: module is from the staging directory, the quality is unknown, you have been warned.
[ 5.639161] bcm2835_vc_sm_cma_probe: Videocore shared memory driver
[ 5.657080] [vc_sm_connected_init]: start
[ 5.688395] media: Linux media interface: v0.10
[ 5.757823] [vc_sm_connected_init]: installed successfully
[ 5.807000] videodev: Linux video capture interface: v2.00
[ 5.862946] bcm2835_mmal_vchiq: module is from the staging directory, the quality is unknown, you have been warned.
[ 5.863298] bcm2835_mmal_vchiq: module is from the staging directory, the quality is unknown, you have been warned.
[ 5.921609] bcm2835_v4l2: module is from the staging directory, the quality is unknown, you have been warned.
[ 5.987876] bcm2835_codec: module is from the staging directory, the quality is unknown, you have been warned.
[ 6.018068] bcm2835-codec bcm2835-codec: Device registered as /dev/video10
[ 6.035235] bcm2835-codec bcm2835-codec: Loaded V4L2 decode
[ 6.051215] bcm2835-codec bcm2835-codec: Device registered as /dev/video11
[ 6.062523] bcm2835-codec bcm2835-codec: Loaded V4L2 encode
[ 6.095781] bcm2835-codec bcm2835-codec: Device registered as /dev/video12
[ 6.109036] bcm2835-codec bcm2835-codec: Loaded V4L2 isp
[ 6.207374] usbcore: registered new interface driver usbserial_generic
[ 6.224695] usbserial: USB Serial support registered for generic
[ 6.241016] usbcore: registered new interface driver ftdi_sio
[ 6.241154] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 6.241727] ftdi_sio 1-1.3:1.0: FTDI USB Serial Device converter detected
[ 6.242029] usb 1-1.3: Detected FT8U232AM
[ 6.249686] usb 1-1.3: FTDI USB Serial Device converter now attached to ttyUSB0
[ 6.467103] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 6.480116] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 7.752586] Under-voltage detected! (0x00050005)
[ 7.991588] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xDDE1
[ 8.019658] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 8.422475] Adding 102396k swap on /var/swap. Priority:-2 extents:1 across:102396k SSFS
[ 23.010909] NET: Registered protocol family 3
[ 23.064265] NET: Registered protocol family 5
[ 24.053282] random: crng init done
[ 24.056728] random: 7 urandom warning(s) missed due to ratelimiting
[ 9949.023173] smsc95xx 1-1.1:1.0 eth0: link down
[ 9951.068203] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 9951.187339] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 9951.196352] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 9952.046362] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 9952.177385] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 9952.186340] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 9953.778631] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xDDE1
[ 9953.788845] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 9958.766859] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 9958.897832] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 9959.144162] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 9959.467880] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 9960.998163] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xDDE1
[ 9965.014437] smsc95xx 1-1.1:1.0 eth0: link down
[ 9976.726946] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 9976.957774] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 9976.965326] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[10010.047943] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xDDE1
[10010.058188] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[39731.873810] ftdi_sio ttyUSB0: usb_serial_generic_read_bulk_callback - urb stopped: -32
[39731.881826] ftdi_sio ttyUSB0: usb_serial_generic_read_bulk_callback - urb stopped: -32
[39731.986932] usb 1-1.3: USB disconnect, device number 4
[39731.992527] ftdi_sio ttyUSB0: error from flowcontrol urb
[39731.998808] ftdi_sio ttyUSB0: FTDI USB Serial Device converter now disconnected from ttyUSB0
[39732.007786] ftdi_sio 1-1.3:1.0: device disconnected
[39738.173652] usb 1-1.3: new full-speed USB device number 5 using dwc_otg
[39738.320582] usb 1-1.3: New USB device found, idVendor=0403, idProduct=e0e8, bcdDevice= 2.00
[39738.329045] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[39738.336438] usb 1-1.3: Product: ELV FHZ 1300 PC
[39738.341009] usb 1-1.3: Manufacturer: ELV AG
[39738.345280] usb 1-1.3: SerialNumber: EL3HRM96
[39738.360778] ftdi_sio 1-1.3:1.0: FTDI USB Serial Device converter detected
[39738.367969] usb 1-1.3: Detected FT8U232AM
[39738.372378] usb 1-1.3: FTDI USB Serial Device converter now attached to ttyUSB0

So mit Handynetzteil:
root@raspberrypi:~# dmesg
[ 0.000000] Booting Linux on physical CPU 0xf00
[ 0.000000] Linux version 4.19.80-v7+ (dom@buildbot) (gcc version 4.9.3 (crosstool-NG crosstool-ng-1.22.0-88-g8460611)) #1274 SMP Mon Oct 21 16:23:10 BST 2019
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Raspberry Pi 2 Model B Rev 1.1
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] cma: Reserved 8 MiB at 0x37800000
[ 0.000000] On node 0 totalpages: 229376
[ 0.000000] Normal zone: 2016 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 229376 pages, LIFO batch:63
[ 0.000000] random: get_random_bytes called from start_kernel+0xac/0x4b0 with crng_init=0
[ 0.000000] percpu: Embedded 16 pages/cpu s35392 r8192 d21952 u65536
[ 0.000000] pcpu-alloc: s35392 r8192 d21952 u65536 alloc=16*4096
[ 0.000000] pcpu-alloc:
0
1
2
3
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 227360
[ 0.000000] Kernel command line: coherent_pool=1M bcm2708_fb.fbwidth=656 bcm2708_fb.fbheight=416 bcm2708_fb.fbswap=1 vc_mem.mem_base=0x3ec00000 vc_mem.mem_size=0x40000000 dwc_otg.lpm_enable=0 console=ttyAMA0,115200 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 elevator=deadline rootwait
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 886328K/917504K available (8192K kernel code, 629K rwdata, 2176K rodata, 1024K init, 821K bss, 22984K reserved, 8192K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xb8800000 - 0xff800000 (1136 MB)
lowmem : 0x80000000 - 0xb8000000 ( 896 MB)
modules : 0x7f000000 - 0x80000000 ( 16 MB)
.text : 0x(ptrval) - 0x(ptrval) (9184 kB)
.init : 0x(ptrval) - 0x(ptrval) (1024 kB)
.data : 0x(ptrval) - 0x(ptrval) ( 630 kB)
.bss : 0x(ptrval) - 0x(ptrval) ( 822 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] ftrace: allocating 26403 entries in 78 pages
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] arch_timer: cp15 timer(s) running at 19.20MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[ 0.000010] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[ 0.000030] Switching to timer-based delay loop, resolution 52ns
[ 0.000368] Console: colour dummy device 80x30
[ 0.001083] console [tty1] enabled
[ 0.001157] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[ 0.001212] pid_max: default: 32768 minimum: 301
[ 0.001671] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.001718] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.002986] CPU: Testing write buffer coherency: ok
[ 0.003699] CPU0: update cpu_capacity 1024
[ 0.003741] CPU0: thread -1, cpu 0, socket 15, mpidr 80000f00
[ 0.004768] Setting up static identity map for 0x100000 - 0x10003c
[ 0.005038] rcu: Hierarchical SRCU implementation.
[ 0.006246] smp: Bringing up secondary CPUs ...
[ 0.007571] CPU1: update cpu_capacity 1024
[ 0.007584] CPU1: thread -1, cpu 1, socket 15, mpidr 80000f01
[ 0.009001] CPU2: update cpu_capacity 1024
[ 0.009013] CPU2: thread -1, cpu 2, socket 15, mpidr 80000f02
[ 0.010422] CPU3: update cpu_capacity 1024
[ 0.010434] CPU3: thread -1, cpu 3, socket 15, mpidr 80000f03
[ 0.010605] smp: Brought up 1 node, 4 CPUs
[ 0.010761] SMP: Total of 4 processors activated (153.60 BogoMIPS).
[ 0.010789] CPU: All CPU(s) started in HYP mode.
[ 0.010812] CPU: Virtualization extensions available.
[ 0.012136] devtmpfs: initialized
[ 0.027872] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.028294] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.028360] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.029249] pinctrl core: initialized pinctrl subsystem
[ 0.030696] NET: Registered protocol family 16
[ 0.034250] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[ 0.041968] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.042022] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.042315] Serial: AMBA PL011 UART driver
[ 0.045358] bcm2835-mbox 3f00b880.mailbox: mailbox enabled
[ 0.091391] bcm2835-dma 3f007000.dma: DMA legacy API manager at (ptrval), dmachans=0x1
[ 0.093743] SCSI subsystem initialized
[ 0.094114] usbcore: registered new interface driver usbfs
[ 0.094223] usbcore: registered new interface driver hub
[ 0.094410] usbcore: registered new device driver usb
[ 0.110754] raspberrypi-firmware soc:firmware: Attached to firmware from 2019-10-21 16:50, variant start
[ 0.120325] raspberrypi-firmware soc:firmware: Firmware hash is 509fb1bcb9511d963439429724a6f6dfb8251107
[ 0.132416] clocksource: Switched to clocksource arch_sys_counter
[ 0.235173] VFS: Disk quotas dquot_6.6.0
[ 0.235326] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.235643] FS-Cache: Loaded
[ 0.235992] CacheFiles: Loaded
[ 0.250771] NET: Registered protocol family 2
[ 0.251904] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
[ 0.251988] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.252143] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.252357] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.252686] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.252780] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.253302] NET: Registered protocol family 1
[ 0.254226] RPC: Registered named UNIX socket transport module.
[ 0.254271] RPC: Registered udp transport module.
[ 0.254297] RPC: Registered tcp transport module.
[ 0.254322] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.256415] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[ 0.260576] Initialise system trusted keyrings
[ 0.260942] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[ 0.274809] FS-Cache: Netfs 'nfs' registered for caching
[ 0.275686] NFS: Registering the id_resolver key type
[ 0.275752] Key type id_resolver registered
[ 0.275779] Key type id_legacy registered
[ 0.275819] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.279161] Key type asymmetric registered
[ 0.279207] Asymmetric key parser 'x509' registered
[ 0.279308] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[ 0.279572] io scheduler noop registered
[ 0.279607] io scheduler deadline registered (default)
[ 0.279904] io scheduler cfq registered
[ 0.279938] io scheduler mq-deadline registered (default)
[ 0.279967] io scheduler kyber registered
[ 0.282593] bcm2708_fb soc:fb: FB found 1 display(s)
[ 0.289259] Console: switching to colour frame buffer device 82x26
[ 0.294204] bcm2708_fb soc:fb: Registered framebuffer for display 0, size 656x416
[ 0.300057] bcm2835-rng 3f104000.rng: hwrng registered
[ 0.302064] vc-mem: phys_addr:0x00000000 mem_base=0x3ec00000 mem_size:0x40000000(1024 MiB)
[ 0.306224] vc-sm: Videocore shared memory driver
[ 0.308375] gpiomem-bcm2835 3f200000.gpiomem: Initialised: Registers at 0x3f200000
[ 0.327977] brd: module loaded
[ 0.344112] loop: module loaded
[ 0.346603] Loading iSCSI transport class v2.0-870.
[ 0.349367] libphy: Fixed MDIO Bus: probed
[ 0.351176] usbcore: registered new interface driver lan78xx
[ 0.352971] usbcore: registered new interface driver smsc95xx
[ 0.354590] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[ 0.384135] dwc_otg 3f980000.usb: base=(ptrval)
[ 0.586138] Core Release: 2.80a
[ 0.587769] Setting default values for core params
[ 0.589447] Finished setting default values for core params
[ 0.791515] Using Buffer DMA mode
[ 0.793179] Periodic Transfer Interrupt Enhancement - disabled
[ 0.794829] Multiprocessor Interrupt Enhancement - disabled
[ 0.796435] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 0.798033] Dedicated Tx FIFOs mode
[ 0.800235] WARN::dwc_otg_hcd_init:1045: FIQ DMA bounce buffers: virt = b7914000 dma = 0xf7914000 len=9024
[ 0.803420] FIQ FSM acceleration enabled for :
Non-periodic Split Transactions
Periodic Split Transactions
High-Speed Isochronous Endpoints
Interrupt/Control Split Transaction hack enabled
[ 0.810823] dwc_otg: Microframe scheduler enabled
[ 0.810911] WARN::hcd_init_fiq:457: FIQ on core 1
[ 0.812442] WARN::hcd_init_fiq:458: FIQ ASM at 806564a0 length 36
[ 0.813957] WARN::hcd_init_fiq:497: MPHI regs_base at b8810000
[ 0.815507] dwc_otg 3f980000.usb: DWC OTG Controller
[ 0.817077] dwc_otg 3f980000.usb: new USB bus registered, assigned bus number 1
[ 0.818682] dwc_otg 3f980000.usb: irq 56, io mem 0x00000000
[ 0.820270] Init: Port Power? op_state=1
[ 0.821799] Init: Power Port (0)
[ 0.823666] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[ 0.826730] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.828375] usb usb1: Product: DWC OTG Controller
[ 0.829990] usb usb1: Manufacturer: Linux 4.19.80-v7+ dwc_otg_hcd
[ 0.831639] usb usb1: SerialNumber: 3f980000.usb
[ 0.834159] hub 1-0:1.0: USB hub found
[ 0.835768] hub 1-0:1.0: 1 port detected
[ 0.838055] dwc_otg: FIQ enabled
[ 0.838063] dwc_otg: NAK holdoff enabled
[ 0.838070] dwc_otg: FIQ split-transaction FSM enabled
[ 0.838083] Module dwc_common_port init
[ 0.838493] usbcore: registered new interface driver usb-storage
[ 0.840337] mousedev: PS/2 mouse device common for all mice
[ 0.843079] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer
[ 0.845008] bcm2835-cpufreq: min=600000 max=900000
[ 0.847233] sdhci: Secure Digital Host Controller Interface driver
[ 0.848874] sdhci: Copyright(c) Pierre Ossman
[ 0.851013] sdhost-bcm2835 3f202000.mmc: could not get clk, deferring probe
[ 0.852956] sdhci-pltfm: SDHCI platform and OF driver helper
[ 0.855526] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.857405] hidraw: raw HID events driver (C) Jiri Kosina
[ 0.859367] usbcore: registered new interface driver usbhid
[ 0.861084] usbhid: USB HID core driver
[ 0.863780] vchiq: vchiq_init_state: slot_zero = (ptrval), is_master = 0
[ 0.867452] [vc_sm_connected_init]: start
[ 0.876271] [vc_sm_connected_init]: end - returning 0
[ 0.879431] Initializing XFRM netlink socket
[ 0.881080] NET: Registered protocol family 17
[ 0.882882] Key type dns_resolver registered
[ 0.884864] Registering SWP/SWPB emulation handler
[ 0.887463] registered taskstats version 1
[ 0.889093] Loading compiled-in X.509 certificates
[ 0.899995] uart-pl011 3f201000.serial: cts_event_workaround enabled
[ 0.901778] 3f201000.serial: ttyAMA0 at MMIO 0x3f201000 (irq = 81, base_baud = 0) is a PL011 rev2
[ 1.903694] console [ttyAMA0] enabled
[ 1.911745] sdhost: log_buf @ (ptrval) (f7913000)
[ 1.965222] mmc0: sdhost-bcm2835 loaded - DMA enabled (>1)
[ 1.974052] of_cfs_init
[ 1.978202] of_cfs_init: OK
[ 1.983597] Waiting for root device /dev/mmcblk0p2...
[ 2.012592] Indeed it is in host mode hprt0 = 00021501
[ 2.086448] mmc0: host does not support reading read-only switch, assuming write-enable
[ 2.099850] mmc0: new high speed SDHC card at address 0001
[ 2.108528] mmcblk0: mmc0:0001 00000 14.6 GiB
[ 2.109672] random: fast init done
[ 2.121307] mmcblk0: p1 p2
[ 2.147926] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 2.159449] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[ 2.169144] devtmpfs: mounted
[ 2.179616] Freeing unused kernel memory: 1024K
[ 2.186330] Run /sbin/init as init process
[ 2.222492] usb 1-1: new high-speed USB device number 2 using dwc_otg
[ 2.230863] Indeed it is in host mode hprt0 = 00001101
[ 2.472908] usb 1-1: New USB device found, idVendor=0424, idProduct=9514, bcdDevice= 2.00
[ 2.484664] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.494640] hub 1-1:1.0: USB hub found
[ 2.500424] hub 1-1:1.0: 5 ports detected
[ 2.783754] systemd[1]: System time before build time, advancing clock.
[ 2.822485] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
[ 2.950239] NET: Registered protocol family 10
[ 2.953047] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00, bcdDevice= 2.00
[ 2.958470] Segment Routing with IPv6
[ 2.968705] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.986815] smsc95xx v1.0.6
[ 3.015233] random: systemd: uninitialized urandom read (16 bytes read)
[ 3.034983] random: systemd: uninitialized urandom read (16 bytes read)
[ 3.051834] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN)
[ 3.076600] systemd[1]: Detected architecture arm.
[ 3.077611] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-3f980000.usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:dc:3d:55
[ 3.106425] systemd[1]: Set hostname to <raspberrypi>.
[ 3.192630] usb 1-1.2: new full-speed USB device number 4 using dwc_otg
[ 3.220888] uart-pl011 3f201000.serial: no DMA platform data
[ 3.236927] random: systemd-cryptse: uninitialized urandom read (16 bytes read)
[ 3.349627] usb 1-1.2: New USB device found, idVendor=0403, idProduct=e0e8, bcdDevice= 2.00
[ 3.361850] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3.371204] usb 1-1.2: Product: ELV FHZ 1300 PC
[ 3.377708] usb 1-1.2: Manufacturer: ELV AG
[ 3.383827] usb 1-1.2: SerialNumber: EL3HRM96
[ 3.953464] systemd[1]: Listening on RPCbind Server Activation Socket.
[ 3.965707] systemd[1]: Listening on udev Control Socket.
[ 3.998089] systemd[1]: Reached target Swap.
[ 4.008451] systemd[1]: Created slice System Slice.
[ 4.018976] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ 4.034599] systemd[1]: Mounting RPC Pipe File System...
[ 4.051306] systemd[1]: Mounting Debug File System...
[ 4.275341] snd_bcm2835: module is from the staging directory, the quality is unknown, you have been warned.
[ 4.563153] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 4.713775] systemd-journald[106]: Received request to flush runtime journal from PID 1
[ 5.302333] media: Linux media interface: v0.10
[ 5.310277] vc_sm_cma: module is from the staging directory, the quality is unknown, you have been warned.
[ 5.354426] bcm2835_vc_sm_cma_probe: Videocore shared memory driver
[ 5.359283] videodev: Linux video capture interface: v2.00
[ 5.371610] [vc_sm_connected_init]: start
[ 5.391456] [vc_sm_connected_init]: installed successfully
[ 5.416649] bcm2835_mmal_vchiq: module is from the staging directory, the quality is unknown, you have been warned.
[ 5.435957] bcm2835_mmal_vchiq: module is from the staging directory, the quality is unknown, you have been warned.
[ 5.470040] bcm2835_codec: module is from the staging directory, the quality is unknown, you have been warned.
[ 5.491750] bcm2835_v4l2: module is from the staging directory, the quality is unknown, you have been warned.
[ 5.560572] bcm2835-codec bcm2835-codec: Device registered as /dev/video10
[ 5.571970] bcm2835-codec bcm2835-codec: Loaded V4L2 decode
[ 5.604021] bcm2835-codec bcm2835-codec: Device registered as /dev/video11
[ 5.632742] bcm2835-codec bcm2835-codec: Loaded V4L2 encode
[ 5.657872] bcm2835-codec bcm2835-codec: Device registered as /dev/video12
[ 5.670297] bcm2835-codec bcm2835-codec: Loaded V4L2 isp
[ 5.858556] usbcore: registered new interface driver usbserial_generic
[ 5.870757] usbserial: USB Serial support registered for generic
[ 5.908145] usbcore: registered new interface driver ftdi_sio
[ 5.918182] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 5.938624] ftdi_sio 1-1.2:1.0: FTDI USB Serial Device converter detected
[ 5.955478] usb 1-1.2: Detected FT8U232AM
[ 5.966892] usb 1-1.2: FTDI USB Serial Device converter now attached to ttyUSB0
[ 6.262725] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 6.272325] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 7.682352] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xDDE1
[ 7.724369] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 8.055157] Adding 102396k swap on /var/swap. Priority:-2 extents:1 across:102396k SSFS
[ 21.641807] NET: Registered protocol family 3
[ 21.688557] NET: Registered protocol family 5
[ 24.588705] random: crng init done
[ 24.592224] random: 7 urandom warning(s) missed due to ratelimiting

Otto123 · 22 Oktober 2019, 11:38:10

Moin,

bitte editiere Deinen Beitrag und formatiere ihn etwas leserlicher mit Codetags -> https://forum.fhem.de/index.php/topic,71806.0.html
Deine eigentliche Frage ist sicher in der fehlenden Formatierung untergegangen.

Das das Netzteil kaputt/unbrauchbar ist hast Du ja schon gemerkt. Ich denke auch Deine SD Karte hat einen Schuss, zumindest ist das wahrscheinlich.
Also mach als erstes ein Backup von FHEM nimm eine neue SD Card und installiere FHEM neu und sichere Dein Altes zurück. Mal sehen ob es dann besser läuft.
Wenn Du keinen Plan hast wie Du es machen sollst frag nochmal nach

Gruß Otto

malip · 24 Oktober 2019, 12:31:02

Danke.
Mit einem neuen Netzteil gehen die Kommandos wieder durch (9€)
https://www.amazon.de/dp/B06Y1F76P9?ref_=pe_3044161_248799201_302_E_DDE_dt_1
5,1 V / 3 A Micro-USB Netzteil für Raspberry Pi 3, Vorgängermodelle, Banana Pi;
erheblich reduzierter Kabel-Spannungsabfall! Kein buntes Quadrat und Blitzsymbol mehr! 2 Doppel-Pi-Filter

Mache trotzdem mal eine neue sd Karte rein (nochmal 9€)
SanDisk Ultra Android microSDHC 16GB bis zu 80 MB/Sek Class 10 Speicherkarte + SD-Adapter

Mit win32 diskimager ruckizucki (hoffe ich gleich zumindest..J)

FHEM Forum

sehr langsame Kommandos zu den Rollos und nur sporadisch

malip

Otto123

malip