JeeLink defekt?

[arthur_dent_2015]

Moin zusammen,
seit einem crash meines Raspis reagiert mein JeeLink nicht mehr. Beide LED's, Blau und Rot, blinken nur noch hektisch. Neu flashen hat keine Besserung gebracht
Im Log kommen ständig Einträge wie dieser:

Code Auswählen Erweitern


2021.02.06 18:31:50 3: Jeelink_PCA: Unknown code , help me!

Bei verbose=5 sieht das dann so aus:

Code Auswählen Erweitern


2021.02.06 18:31:54 5: JeeLink/RAW:        <n>/ e    - turn on device <n>
  0x<hhhh> h    - set center frequency (Example 0xA6FE == Frequency - 868.9500MHz
       <n> p    - poll device <n>
       <n> r    - list recordings
       <n> q    - quiet mode (1=suppress TX and bad packets)
       <n> v
2021.02.06 18:31:54 5: JeeLink/RAW:        <n> v/    - version and configuration report


2021.02.06 18:31:54 5: JeeLink/RAW: /
[pcaSerial.10.1]

Available commands:
     ..,.. s    - send data packet
           l    - list devices
       <n> a    - turn activity LED on PB1 on or off
       <n> c    - config (0=fill, 1=load, 2=save, 3=erase)
       <n> d    - turn off devi
2021.02.06 18:31:54 5: JeeLink/RAW:        <n> d    - turn off devi/ce <n>
       <n> e    - turn on device <n>
  0x<hhhh> h    - set center frequency (Example 0xA6FE == Frequency - 868.9500MHz
       <n> p    - poll device <n>
       <n> r    - list recordings
       <n> q    - quiet mode (1=suppress TX and bad pack
2021.02.06 18:31:54 5: JeeLink/RAW:        <n> q    - quiet mode (1=suppress TX and bad pack/ets)
       <n> v    - version and configuration report

List vom JeeLink:

Code Auswählen Erweitern


Internals:
   Clients    :PCA301:EC3000:RoomNode:LaCrosse:ETH200comfort:CUL_IR:HX2272:FS20:AliRF:Level:EMT7110:KeyValueProtocol
   DEF        /dev/serial/by-path/platform-fd500000.pcie-pci-0000:01:00.0-usb-0:1.1.1.3:1.0-port0@57600
   DeviceName /dev/serial/by-path/platform-fd500000.pcie-pci-0000:01:00.0-usb-0:1.1.1.3:1.0-port0@57600
   FD         128
   FUUID      601eed3e-f33f-052b-9ed6-1b793ab9405d33e7
   FVERSION   36_JeeLink.pm:0.147070/2017-07-13
   Jeelink_PCA_MSGCNT 2256
   Jeelink_PCA_TIME 2021-02-07 11:48:23
   NAME       Jeelink_PCA
   NR         951
   NR_CMD_LAST_H 15
   PARTIAL      0x<hhhh> h    - set center frequency (Example 0xA6FE == Frequency -
   RAWMSG     
   STATE      initialized
   TYPE       JeeLink
   initMessages
   model      [pcaSerial.10.1]
   Helper:
     DBLOG:
       state:
         fhemlogDB:
           TIME       1612694903.87968
           VALUE      UNKNOWNCODE
   MatchList:
     1:PCA301   ^\S+\s+24
     2:EC3000   ^\S+\s+22
     3:RoomNode ^\S+\s+11
     4:LaCrosse ^(\S+\s+9 |OK\sWS\s)
     5:AliRF    ^\S+\s+5
     6:EMT7110  ^OK\sEMT7110\s
     7:KeyValueProtocol ^OK\sVALUES\s
   READINGS:
     2021-02-07 11:48:23   state           initialized
   XMIT_TIME:
     1612691487.76907
     1612691488.7817
     1612691489.79419
     1612691492.66391
     1612691493.67625
     1612691565.90879
     1612691567.11715
     1612691568.145
     1612691569.15868
     1612691570.17215
     1612691570.89849
     1612691571.93084
     1612691573.00467
     1612691574.07601
     1612691575.1441
Attributes:
   devStateIcon initialized:rc_GREEN disconnected:rc_RED opened:rc_YELLOW
   flashCommand avrdude -p atmega328P -c arduino -P [PORT] -D -U flash:w:[HEXFILE] 2>[LOGFILE]
   initCommands 868950f v
   room       Radios

Jemand eine Idee wie ich den wieder zum Leben erwecken kann?
Danke & Gruß
Arthur