FHEM - Hausautomations-Systeme > ZWave

ZMNHND1 Flush 1D keine endpointChildren (gelöst)

(1/2) > >>

Roderich:
Hallo,
ich habe ein neues Flush 1D angelernt.
Leider wurden die endpointChildren nicht angelegt.

der Befehl

--- Code: ---set ZWave_SWITCH_BINARY_63 mcCreateAll
--- Ende Code ---

liefert leider den Fehler

--- Code: ---Unknown argument mcCreateAll
--- Ende Code ---

Hat jemand eine Idee für mich?


--- Code: ---Internals:
   CFGFN     
   DEF        c9dee6e6 63
   FUUID      6166e1dd-f33f-dfb2-d130-a9f7793fe168b6e0
   IODev      ZWDongle_0
   LASTInputDev ZWDongle_0
   MSGCNT     40
   NAME       ZWave_SWITCH_BINARY_63
   NR         1037
   STATE      on
   TYPE       ZWave
   ZWDongle_0_MSGCNT 40
   ZWDongle_0_RAWMSG 0004003f032503ffca00
   ZWDongle_0_TIME 2021-10-13 16:42:47
   ZWaveSubDevice no
   cmdsPending 0
   homeId     c9dee6e6
   isWakeUp   
   lastMsgSent 1634136167.33171
   nodeIdHex  3f
   READINGS:
     2021-10-13 15:40:45   IODev           ZWDongle_0
     2021-10-13 15:55:53   configActivateDeactivateFunctionsALLON10 ALLONActiveALLOFFActive
     2021-10-13 15:55:54   configAutomaticTurningOffRelayAfterSet11 0
     2021-10-13 15:55:54   configAutomaticTurningOnOffSecondsOr15 seconds
     2021-10-13 15:55:54   configAutomaticTurningOnRelayAfterSet12 0
     2021-10-13 15:55:54   configDigitalTemperatureSensor120 5
     2021-10-13 15:55:54   configEnableDisableEndpointsI2OrSelect100 SensorBinary
     2021-10-13 15:55:54   configInput1SwitchType BiStableSwitchType
     2021-10-13 15:55:54   configInput2ContactType NONormalyOpenInputType
     2021-10-13 15:55:54   configOutputSwitchSelection WhenSystemIsTurnedOffTheOutput0
     2021-10-13 15:55:59   configSavingTheStateOfTheRelayAfterA30 Flush1RelayModuleSavesItsState0
     2021-10-13 15:55:59   configTemperatureSensorOffsetSettings 32536
     2021-10-13 15:54:33   mcaGroups       6
     2021-10-13 15:54:33   mca_1           Max 1 Nodes ZWDongle_0
     2021-10-13 15:54:33   mca_2           Max 16
     2021-10-13 15:54:33   mca_3           Max 16
     2021-10-13 15:54:33   mca_4           Max 16
     2021-10-13 15:54:33   mca_5           Max 16
     2021-10-13 15:54:33   mca_6           Max 16
     2021-10-13 15:41:50   model           Qubino (Goap) ZMNHND1 Flush 1D relay
     2021-10-13 15:41:50   modelConfig     qubino/ZMNHNDx.xml
     2021-10-13 15:41:50   modelId         0159-0002-0053
     2021-10-13 16:42:47   reportedState   on
     2021-10-13 16:42:47   routeInfo       timeToCb:0.02 repeaters:0 rssi0:-55 dBm ackCh:0 lastCh:0 scheme:LastWorkingRoute rep:at 100kbps routeTries:1 lastFailed:
     2021-10-13 16:42:47   state           on
     2021-10-13 16:42:47   timeToAck       0.192
     2021-10-13 16:42:47   transmit        OK
     2021-10-13 15:42:18   zwavePlusInfo    version:01 role:AlwaysOnSlave node:Z-Wave+Node installerIcon:0702 userIcon:0700
Attributes:
   classes    ZWAVEPLUS_INFO VERSION MANUFACTURER_SPECIFIC DEVICE_RESET_LOCALLY POWERLEVEL SWITCH_ALL SWITCH_BINARY ASSOCIATION MULTI_CHANNEL_ASSOCIATION ASSOCIATION_GRP_INFO CONFIGURATION MARK
   room       ZWave
   vclasses   ASSOCIATION:2 ASSOCIATION_GRP_INFO:2 CONFIGURATION:1 DEVICE_RESET_LOCALLY:1 MANUFACTURER_SPECIFIC:2 MULTI_CHANNEL_ASSOCIATION:3 POWERLEVEL:1 SWITCH_ALL:1 SWITCH_BINARY:1 VERSION:2 ZWAVEPLUS_INFO:2
--- Ende Code ---

rudolfkoenig:
Fuer mcCreateAll braucht man die Klasse MULTI_CHANNEL.
MULTI_CHANNEL_ASSOCIATION ist was anders.

Grob:
- MULTI_CHANNEL: das Geraet unterstuetzt mehrere Kanaele (vulgo Unter-Geraete)
- MULTI_CHANNEL_ASSOCIATION: man kann lokale Kanaele (wenn sie existieren, sonst das Hauptgeraet) mit entfernten Kanaelen verbinden, und nicht nur (wie per ASSOCIATION) jeweils das eine Hauptgeraet mit dem anderen.

Roderich:

--- Zitat von: rudolfkoenig am 13 Oktober 2021, 16:59:31 ---Fuer mcCreateAll braucht man die Klasse MULTI_CHANNEL.
MULTI_CHANNEL_ASSOCIATION ist was anders.

Grob:
- MULTI_CHANNEL: das Geraet unterstuetzt mehrere Kanaele (vulgo Unter-Geraete)
- MULTI_CHANNEL_ASSOCIATION: man kann lokale Kanaele (wenn sie existieren, sonst das Hauptgeraet) mit entfernten Kanaelen verbinden, und nicht nur (wie per ASSOCIATION) jeweils das eine Hauptgeraet mit dem anderen.

--- Ende Zitat ---

Mein letztes Flush 1D hatte das noch. Was kann die Ursache sein, dass diese Klasse nicht mehr vorhanden ist?


--- Code: ---17:39:22   IODev           ZWDongle_0
     2021-10-12 18:35:32   associatedWith  ZWave_SW_Garagentor_Taster,ZWave_KT_Garagentor,ZWave_Node_54.3
     2021-05-08 14:43:13   configActivateDeactivateFunctionsALLON10 ALLONActiveALLOFFActive
     2021-05-08 14:43:13   configAutomaticTurningOffRelayAfterSet11 0
     2021-05-08 14:43:13   configAutomaticTurningOnOffSecondsOr15 seconds
     2021-05-08 14:43:13   configAutomaticTurningOnRelayAfterSet12 0
     2021-05-08 14:43:13   configDigitalTemperatureSensor120 5
     2021-05-08 14:43:13   configEnableDisableEndpointsI2OrSelect100 SensorBinary
     2021-05-08 14:43:13   configInput1SwitchType BiStableSwitchType
     2021-05-08 14:43:13   configInput2ContactType NONormalyOpenInputType
     2021-05-08 14:43:13   configOutputSwitchSelection WhenSystemIsTurnedOffTheOutput0
     2021-05-08 14:43:18   configSavingTheStateOfTheRelayAfterA30 Flush1RelayModuleSavesItsState0
     2021-05-08 14:43:18   configTemperatureSensorOffsetSettings 32536
     2021-05-08 14:40:45   mcCapability_01 ZWAVEPLUS_INFO VERSION SWITCH_ALL SWITCH_BINARY ASSOCIATION MULTI_CHANNEL_ASSOCIATION ASSOCIATION_GRP_INFO MARK
     2021-05-08 14:40:45   mcCapability_02 ZWAVEPLUS_INFO VERSION SENSOR_MULTILEVEL ASSOCIATION MULTI_CHANNEL_ASSOCIATION ASSOCIATION_GRP_INFO
     2021-05-08 14:40:44   mcEndpoints     total 2, different
     2021-05-08 14:46:17   mcaGroups       6
     2021-05-08 14:46:17   mca_1           Max 1 Nodes ZWDongle_0:0
     2021-05-08 14:46:17   mca_2           Max 16
     2021-05-08 14:46:17   mca_3           Max 16
     2021-05-08 14:46:17   mca_4           Max 16
     2021-05-08 14:46:17   mca_5           Max 16
     2021-05-08 14:46:17   mca_6           Max 16
     2021-05-08 14:40:43   model           Qubino (Goap) ZMNHND1 Flush 1D relay
     2021-05-08 14:40:43   modelConfig     qubino/ZMNHNDx.xml
     2021-05-08 14:40:43   modelId         0159-0002-0053
     2021-10-12 17:57:50   reportedState   on
     2021-10-12 18:34:39   state           on
     2021-10-12 17:42:56   timeToAck       0.074
     2021-10-12 18:34:44   transmit        NO_ACK
     2021-05-08 14:41:30   version         Lib 3 Prot 4.05 App 4.1 HW 4 FWCounter 1 FW 4.1
     2021-05-08 14:41:19   zwavePlusInfo   version:01 role:AlwaysOnSlave node:Z-Wave+Node installerIcon:0702 userIcon:0700
Attributes:
   classes    ZWAVEPLUS_INFO VERSION MANUFACTURER_SPECIFIC DEVICE_RESET_LOCALLY POWERLEVEL SWITCH_ALL SWITCH_BINARY SENSOR_MULTILEVEL MULTI_CHANNEL ASSOCIATION MULTI_CHANNEL_ASSOCIATION ASSOCIATION_GRP_INFO CONFIGURATION MARK
   room       Garage
   vclasses   ASSOCIATION:2 ASSOCIATION_GRP_INFO:2 CONFIGURATION:1 DEVICE_RESET_LOCALLY:1 MANUFACTURER_SPECIFIC:2 MULTI_CHANNEL:4 MULTI_CHANNEL_ASSOCIATION:3 POWERLEVEL:1 SENSOR_MULTILEVEL:7 SWITCH_ALL:1 SWITCH_BINARY:1 VERSION:2 ZWAVEPLUS_INFO:2
--- Ende Code ---

rudolfkoenig:
Ich kenne dieses Geraet nicht.
Ich meine gehoert zu haben, dass ein Geraet mit optional anschliessbaren Temperaturfuehler diesen als Untergeraet anbietet, falls vorhanden. Womoeglich kann man die Klasse auch per Konfiguration aktivieren.

Roderich:

--- Zitat von: rudolfkoenig am 13 Oktober 2021, 17:25:03 ---Womoeglich kann man die Klasse auch per Konfiguration aktivieren.

--- Ende Zitat ---

Wie müsste ich da vorgehen?

Navigation

[0] Themen-Index

[#] Nächste Seite

Zur normalen Ansicht wechseln