(erledigt) AMAD2 bekomme keine readings

Begonnen von Helmi55, 10 April 2016, 13:13:47

Vorheriges Thema - Nächstes Thema
Drucken
Nach unten Seiten1 2 Alle
Benutzer-Aktionen

Helmi55

10 April 2016, 13:13:47 Letzte Bearbeitung: 10 April 2016, 17:44:27 von Helmi55
Hallo
so ich habe jetzt AMAD2 nochmals gelöscht und neu aufgesetzt
192.168.0.116 ist die IP des Tablets - das hängt über WLAN im Haus am AP dlink.
FHEM steht in der Garage und ist über Powerlan mit der IP 192.168.0.117 im Netz.
Code Auswählen

2016.04.10 13:01:15 3: AMAD (TabletGarage) - defined with host 192.168.0.116 on port 8090 and AccessPoint-SSID dlink-D22C
2016.04.10 13:01:26 3: AMAD (TabletGarage) - defined with host 192.168.0.116 on port 8090 and AccessPoint-SSID dlink-D22C
2016.04.10 13:01:26 3: AMAD (AMADCommBridge) - defined Bridge with Socketport 8090
2016.04.10 13:01:26 3: AMAD (AMADCommBridge) - Attention!!! By the first run, dont forget to "set AMADCommBridge fhemServerIP <IP-FHEM>"
2016.04.10 13:01:26 3: AMADCommBridge: port 8090 opened


Komme mit der Meldung nicht zurecht: last StatusRequestState

Bin jetzt eigentlich genau wie im wikieintrag vorgegangen?????
System1 fhem 6.1 auf RPi 4B mit 4GB, HMUSBConfig, DS9490R-1Wire, Busware USB 868, Pool-Solarsteuerung mit FHEM. System2 fhem 6.1 auf RPi 4B mit 4GB (Bullseye) mit Busware USB 868 und 433 und HMUARTLGW für Haussteuerung

https://www.flickr.com/photos/canonhelmi/

Thomas X

#1
10 April 2016, 13:31:46
Habe auch gerade ein Problem damit festgestellt. Wenn ich das Gast-WLAN auf meiner Fritte aktiviere, dann bekommt man einen kurzen WLAN-Disconnect. Ab dem Moment muss ich den Flow im Automagic manuell neu starten. Ansonsten kommen keine Werte mehr und Automagic melden, "no route to host".

Ich habe mir da jetzt einen Flow geschrieben, der dann selbstständig den Information-Flow neu startet. Das kann man natürlich auch direkt in den Information-Flow einarbeiten. ;)

Ansonsten ist AMAD eine Super Sache! Vielen Dank dem Author!

CoolTux

#2
10 April 2016, 16:11:30
Zitat von: Helmi55 am 10 April 2016, 13:13:47
Hallo
so ich habe jetzt AMAD2 nochmals gelöscht und neu aufgesetzt
192.168.0.116 ist die IP des Tablets - das hängt über WLAN im Haus am AP dlink.
FHEM steht in der Garage und ist über Powerlan mit der IP 192.168.0.117 im Netz.
Code Auswählen

2016.04.10 13:01:15 3: AMAD (TabletGarage) - defined with host 192.168.0.116 on port 8090 and AccessPoint-SSID dlink-D22C
2016.04.10 13:01:26 3: AMAD (TabletGarage) - defined with host 192.168.0.116 on port 8090 and AccessPoint-SSID dlink-D22C
2016.04.10 13:01:26 3: AMAD (AMADCommBridge) - defined Bridge with Socketport 8090
2016.04.10 13:01:26 3: AMAD (AMADCommBridge) - Attention!!! By the first run, dont forget to "set AMADCommBridge fhemServerIP <IP-FHEM>"
2016.04.10 13:01:26 3: AMADCommBridge: port 8090 opened


Komme mit der Meldung nicht zurecht: last StatusRequestState

Bin jetzt eigentlich genau wie im wikieintrag vorgegangen?????
So sehe ich nur wie das Gerät definiert wurde. Ich brauche ein verbose 5 Log im Normalen Betrieb. Von Bridge und Device.
Am besten noch wärend eines manuellen statusRequest oder wenn das nicht geht einmal beim Device auf das Def drücken und dann gleich wieder auf modify.
Du musst nicht wissen wie es geht! Du musst nur wissen wo es steht, wie es geht.
Support me to buy new test hardware for development: https://www.paypal.com/paypalme/MOldenburg
My FHEM Git: https://git.cooltux.net/FHEM/
Das TuxNet Wiki:
https://www.cooltux.net

CoolTux

#3
10 April 2016, 16:19:03
Zitat von: Thomas X am 10 April 2016, 13:31:46
Habe auch gerade ein Problem damit festgestellt. Wenn ich das Gast-WLAN auf meiner Fritte aktiviere, dann bekommt man einen kurzen WLAN-Disconnect. Ab dem Moment muss ich den Flow im Automagic manuell neu starten. Ansonsten kommen keine Werte mehr und Automagic melden, "no route to host".

Ich habe mir da jetzt einen Flow geschrieben, der dann selbstständig den Information-Flow neu startet. Das kann man natürlich auch direkt in den Information-Flow einarbeiten. ;)

Ansonsten ist AMAD eine Super Sache! Vielen Dank dem Author!

Der Information Flow wird automatisch neu gestartet wenn sich der Batteriestatus oder der Screenstatus ändert. Aussersem bei einem statusRequest von FHEM aus.

Deine Logik die Überwachung in den Information Flow ein zu bauen macht kein Sinn, wenn er deaktiviert ist reagiert er auf keinen Trigger mehr. Daher muss der Flow Fremdüberwacht werden.
Genau das machen die beiden Flows Informations und SetCommands. Sie überwachen sich Gegenseitig.
Du musst nicht wissen wie es geht! Du musst nur wissen wo es steht, wie es geht.
Support me to buy new test hardware for development: https://www.paypal.com/paypalme/MOldenburg
My FHEM Git: https://git.cooltux.net/FHEM/
Das TuxNet Wiki:
https://www.cooltux.net

Helmi55

#4
10 April 2016, 17:10:27
Servus
hier nochmals hoffentlich mit mehr Info für dich
Code Auswählen


Save config
MAIN
Tablet-UI
Tablet-EVAL
Favoriten
Abstellraum
Brunnen
Garage
Garten
Poolsteuerung
AMAD
Energie
Logs
Plots
Statistik
System
Unsorted
Wetter
icoEverything Everything
Logfile
Commandref
Remote doc
Edit files
Select style
Event monitor
updatecheck
update
restart
reread

jump to the end

2016.04.10 17:05:33 3: [UtilsHourCounter] Init Done with Version 1.0.1.0 - 10.12.2014 (john)
Subroutine UtilsHourCounter_Initialize redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 45.
Subroutine appHC_OnYear redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 55.
Subroutine appHC_OnMonth redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 80.
Subroutine appHC_OnWeek redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 104.
Subroutine appHC_OnDay redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 128.
Subroutine appHC_OnHour redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 167.
Subroutine appHC_OnCount redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 184.
Subroutine appHCNotify redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 249.
2016.04.10 17:05:33 1: Including fhem.cfg
Subroutine UtilsHourCounter_Initialize redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 45, <$fh> line 8.
Subroutine appHC_OnYear redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 55, <$fh> line 8.
Subroutine appHC_OnMonth redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 80, <$fh> line 8.
Subroutine appHC_OnWeek redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 104, <$fh> line 8.
Subroutine appHC_OnDay redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 128, <$fh> line 8.
Subroutine appHC_OnHour redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 167, <$fh> line 8.
Subroutine appHC_OnCount redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 184, <$fh> line 8.
Subroutine appHC_OnValueChanged redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 219, <$fh> line 8.
Subroutine appHCNotify redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 249, <$fh> line 8.
2016.04.10 17:05:33 3: telnetPort: port 7072 opened
2016.04.10 17:05:34 3: WEB: port 8083 opened
2016.04.10 17:05:34 3: WEBphone: port 8084 opened
2016.04.10 17:05:34 3: WEBtablet: port 8085 opened
2016.04.10 17:05:34 2: eventTypes: loaded 958 events from ./log/eventTypes.txt
2016.04.10 17:05:34 3: Opening CUL_0 device /dev/ttyACM0
2016.04.10 17:05:34 3: Setting CUL_0 serial parameters to 9600,8,N,1
2016.04.10 17:05:34 3: CUL_0 device opened
2016.04.10 17:05:35 3: CUL_0: Possible commands: BbCFiAZEGMKUYRTVWXefmltux
2016.04.10 17:05:35 1: HMLAN_Parse: HMUSB new condition disconnected
2016.04.10 17:05:35 3: Opening HMUSB device 127.0.0.1:1234
2016.04.10 17:05:35 3: HMUSB device opened
2016.04.10 17:05:35 1: HMLAN_Parse: HMUSB new condition init
2016.04.10 17:05:35 3: TABLETUI: new ext defined infix:ftui/: dir:./www/tablet:
2016.04.10 17:05:35 3: Registering HTTPSRV TABLETUI for URL /ftui   and assigned link ftui/ ...
2016.04.10 17:05:35 3: TABLETUIEVAL: new ext defined infix:ftui_eval/: dir:./www/tablet_eval:
2016.04.10 17:05:35 3: Registering HTTPSRV TABLETUIEVAL for URL /ftui_eval   and assigned link ftui_eval/ ...
2016.04.10 17:05:37 3: HourCounter HourCounter Initialize.220 Init Done with Version 1.0.1.2 - 24.12.2014
2016.04.10 17:05:37 0: HourCounter CN.SolarPumpe Define.228 parameters: CN.SolarPumpe HourCounter SolarPumpe:on SolarPumpe:off
2016.04.10 17:05:37 0: HourCounter CN.PoolPumpe Define.228 parameters: CN.PoolPumpe HourCounter PoolPumpe:on PoolPumpe:off
2016.04.10 17:05:37 0: HourCounter CN.Roboter_sw4 Define.228 parameters: CN.Roboter_sw4 HourCounter Roboter_sw4:on Roboter_sw4:off
2016.04.10 17:05:37 0: HourCounter CN.AbstellraumHZ Define.228 parameters: CN.AbstellraumHZ HourCounter AbstellraumHZ:on AbstellraumHZ:off
2016.04.10 17:05:37 0: HourCounter CN.Gartenbeleuchtung Define.228 parameters: CN.Gartenbeleuchtung HourCounter Gartenbeleuchtung:on Gartenbeleuchtung:off
2016.04.10 17:05:37 0: HourCounter CN.Poolbeleuchtung Define.228 parameters: CN.Poolbeleuchtung HourCounter Poolbeleuchtung:on Poolbeleuchtung:off
Constant subroutine main::URL redefined at /usr/share/perl/5.14/constant.pm line 136, <$fh> line 709.
2016.04.10 17:05:37 3: [Daemmerung] 0 attempt(s) needed to get valid weather data from yahoo
2016.04.10 17:05:38 3: AMAD (TabletGarage) - defined with host 192.168.0.116 on port 8090 and AccessPoint-SSID dlink-D22C
2016.04.10 17:05:38 3: AMAD (AMADCommBridge) - defined Bridge with Socketport 8090
2016.04.10 17:05:38 3: AMAD (AMADCommBridge) - Attention!!! By the first run, dont forget to "set AMADCommBridge fhemServerIP <IP-FHEM>"
2016.04.10 17:05:38 3: AMADCommBridge: port 8090 opened
2016.04.10 17:05:38 1: Including ./log/fhem.save
2016.04.10 17:05:38 3: Device GaragenTor added to ActionDetector with 028:00 time
2016.04.10 17:05:38 3: EMONITOR_InitSingle: found new AbstellraumHZ with type CUL_HM
2016.04.10 17:05:38 2: EMONITOR_InitSingle: Warning device AbstellraumHZ rd energy energy 0 !
2016.04.10 17:05:38 3: EMONITOR_InitSingle: found new Gartenbeleuchtung with type FS20
2016.04.10 17:05:38 3: EMONITOR_InitSingle: found new PoolPumpe with type CUL_HM
2016.04.10 17:05:38 2: EMONITOR_InitSingle: Warning device PoolPumpe rd energy energy 0 !
2016.04.10 17:05:38 3: EMONITOR_InitSingle: found new Poolbeleuchtung with type FS20
2016.04.10 17:05:38 3: EMONITOR_InitSingle: found new Roboter_sw4 with type CUL_HM
2016.04.10 17:05:38 2: EMONITOR_InitSingle: Warning device Roboter_sw4 rd energy energy 0 !
2016.04.10 17:05:38 3: EMONITOR_InitSingle: found new SolarPumpe with type CUL_HM
2016.04.10 17:05:38 2: EMONITOR_InitSingle: Warning device SolarPumpe rd energy energy 0 !
2016.04.10 17:05:38 3: EMONITOR_Init2: found 6 devices
2016.04.10 17:05:39 1: usb create starting
2016.04.10 17:05:39 3: Probing CUL device /dev/ttyAMA0
2016.04.10 17:05:39 3: Probing TCM_ESP3 device /dev/ttyAMA0
2016.04.10 17:05:40 3: Probing FRM device /dev/ttyAMA0
2016.04.10 17:05:45 1: usb create end
2016.04.10 17:05:45 3: myOWServer: Opening connection to OWServer localhost:4304...
2016.04.10 17:05:45 3: myOWServer: Successfully connected to localhost:4304.
2016.04.10 17:05:47 2: SecurityCheck:  telnetPort has no associated allowed device with password/globalpassword.  Restart FHEM for a new check if the problem is fixed, or set the global attribute motd to none to supress this message.
2016.04.10 17:05:47 0: Featurelevel: 5.7
2016.04.10 17:05:47 0: Server started with 152 defined entities (fhem.pl:11191/2016-04-05 perl:5.014002 os:linux user:fhem pid:28041)
2016.04.10 17:05:47 3: CUL_HM set PoolPumpe statusRequest
2016.04.10 17:05:50 1: HMLAN_Parse: HMUSB new condition ok
2016.04.10 17:05:52 3: CUL_HM set SolarPumpe statusRequest
2016.04.10 17:05:53 0: HourCounter CN.AbstellraumHZ Run.598 first run done countsOverall:1
2016.04.10 17:05:53 0: HourCounter CN.SolarPumpe Run.598 first run done countsOverall:10
2016.04.10 17:05:53 0: HourCounter CN.Roboter_sw4 Run.598 first run done countsOverall:2
2016.04.10 17:05:53 0: HourCounter CN.Gartenbeleuchtung Run.598 first run done countsOverall:14
2016.04.10 17:05:53 0: HourCounter CN.Poolbeleuchtung Run.598 first run done countsOverall:2
2016.04.10 17:05:54 0: HourCounter CN.PoolPumpe Run.598 first run done countsOverall:18
2016.04.10 17:05:54 5: AMAD (TabletGarage) - Send statusRequest with URL: "http://192.168.0.116:8090/fhem-amad/deviceInfo/" and Header: "fhemIP: 192.168.0.117
fhemDevice: TabletGarage
activeTask: none
apSSID: dlink-D22C"
2016.04.10 17:05:54 3: CUL_HM set AbstellraumHZ statusRequest
2016.04.10 17:05:55 3: CUL_HM set Roboter_sw4 statusRequest
2016.04.10 17:06:07 3: EMONITOR_Init2: found 6 devices
2016.04.10 17:06:32 5: AMAD (TabletGarage) - set TabletGarage statusRequest
2016.04.10 17:06:32 5: AMAD (TabletGarage) - Send statusRequest with URL: "http://192.168.0.116:8090/fhem-amad/deviceInfo/" and Header: "fhemIP: 192.168.0.117
fhemDevice: TabletGarage
activeTask: none
apSSID: dlink-D22C"
2016.04.10 17:07:13 3: AMAD (TabletGarage) - defined with host 192.168.0.116 on port 8090 and AccessPoint-SSID dlink-D22C
2016.04.10 17:07:18 3: HourCounter CN.Poolbeleuchtung Undef.272 Done
2016.04.10 17:07:18 3: HourCounter CN.Gartenbeleuchtung Undef.272 Done
2016.04.10 17:07:18 3: HourCounter CN.AbstellraumHZ Undef.272 Done
2016.04.10 17:07:18 3: HourCounter CN.Roboter_sw4 Undef.272 Done
2016.04.10 17:07:18 3: HourCounter CN.PoolPumpe Undef.272 Done
2016.04.10 17:07:18 3: HourCounter CN.SolarPumpe Undef.272 Done
2016.04.10 17:07:18 3: Unregistering HTTPSRV TABLETUIEVAL for URL /ftui_eval...
2016.04.10 17:07:18 3: Unregistering HTTPSRV TABLETUI for URL /ftui...
2016.04.10 17:07:18 1: PERL WARNING: Subroutine UtilsHourCounter_Initialize redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 45.
2016.04.10 17:07:18 1: PERL WARNING: Subroutine appHC_OnYear redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 55.
2016.04.10 17:07:18 1: PERL WARNING: Subroutine appHC_OnMonth redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 80.
2016.04.10 17:07:18 1: PERL WARNING: Subroutine appHC_OnWeek redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 104.
2016.04.10 17:07:18 1: PERL WARNING: Subroutine appHC_OnDay redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 128.
2016.04.10 17:07:18 1: PERL WARNING: Subroutine appHC_OnHour redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 167.
2016.04.10 17:07:18 1: PERL WARNING: Subroutine appHC_OnCount redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 184.
2016.04.10 17:07:18 1: PERL WARNING: Subroutine appHC_OnValueChanged redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 219.
2016.04.10 17:07:18 1: PERL WARNING: Subroutine appHCNotify redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 249.
2016.04.10 17:07:18 1: Including fhem.cfg
2016.04.10 17:07:18 1: PERL WARNING: Subroutine UtilsHourCounter_Initialize redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 45, <$fh> line 8.
2016.04.10 17:07:18 1: PERL WARNING: Subroutine appHC_OnYear redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 55, <$fh> line 8.
2016.04.10 17:07:18 1: PERL WARNING: Subroutine appHC_OnMonth redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 80, <$fh> line 8.
2016.04.10 17:07:18 1: PERL WARNING: Subroutine appHC_OnWeek redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 104, <$fh> line 8.
2016.04.10 17:07:18 1: PERL WARNING: Subroutine appHC_OnDay redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 128, <$fh> line 8.
2016.04.10 17:07:18 1: PERL WARNING: Subroutine appHC_OnHour redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 167, <$fh> line 8.
2016.04.10 17:07:18 1: PERL WARNING: Subroutine appHC_OnCount redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 184, <$fh> line 8.
2016.04.10 17:07:18 1: PERL WARNING: Subroutine appHC_OnValueChanged redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 219, <$fh> line 8.
2016.04.10 17:07:18 1: PERL WARNING: Subroutine appHCNotify redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 249, <$fh> line 8.
2016.04.10 17:07:18 3: telnetPort: port 7072 opened
2016.04.10 17:07:18 3: WEB: port 8083 opened
2016.04.10 17:07:18 3: WEBphone: port 8084 opened
2016.04.10 17:07:18 3: WEBtablet: port 8085 opened
2016.04.10 17:07:18 2: eventTypes: loaded 958 events from ./log/eventTypes.txt
2016.04.10 17:07:18 3: Opening CUL_0 device /dev/ttyACM0
2016.04.10 17:07:18 3: Setting CUL_0 serial parameters to 9600,8,N,1
2016.04.10 17:07:18 3: CUL_0 device opened
2016.04.10 17:07:18 3: CUL_0: Possible commands: BbCFiAZEGMKUYRTVWXefmltux
2016.04.10 17:07:19 1: HMLAN_Parse: HMUSB new condition disconnected
2016.04.10 17:07:19 3: Opening HMUSB device 127.0.0.1:1234
2016.04.10 17:07:19 3: HMUSB device opened
2016.04.10 17:07:19 1: HMLAN_Parse: HMUSB new condition init
2016.04.10 17:07:19 3: TABLETUI: new ext defined infix:ftui/: dir:./www/tablet:
2016.04.10 17:07:19 3: Registering HTTPSRV TABLETUI for URL /ftui   and assigned link ftui/ ...
2016.04.10 17:07:19 3: TABLETUIEVAL: new ext defined infix:ftui_eval/: dir:./www/tablet_eval:
2016.04.10 17:07:19 3: Registering HTTPSRV TABLETUIEVAL for URL /ftui_eval   and assigned link ftui_eval/ ...
2016.04.10 17:07:19 0: HourCounter CN.SolarPumpe Define.228 parameters: CN.SolarPumpe HourCounter SolarPumpe:on SolarPumpe:off
2016.04.10 17:07:19 0: HourCounter CN.PoolPumpe Define.228 parameters: CN.PoolPumpe HourCounter PoolPumpe:on PoolPumpe:off
2016.04.10 17:07:19 0: HourCounter CN.Roboter_sw4 Define.228 parameters: CN.Roboter_sw4 HourCounter Roboter_sw4:on Roboter_sw4:off
2016.04.10 17:07:19 0: HourCounter CN.AbstellraumHZ Define.228 parameters: CN.AbstellraumHZ HourCounter AbstellraumHZ:on AbstellraumHZ:off
2016.04.10 17:07:19 0: HourCounter CN.Gartenbeleuchtung Define.228 parameters: CN.Gartenbeleuchtung HourCounter Gartenbeleuchtung:on Gartenbeleuchtung:off
2016.04.10 17:07:19 0: HourCounter CN.Poolbeleuchtung Define.228 parameters: CN.Poolbeleuchtung HourCounter Poolbeleuchtung:on Poolbeleuchtung:off
2016.04.10 17:07:19 3: [Daemmerung] 0 attempt(s) needed to get valid weather data from yahoo
2016.04.10 17:07:20 3: AMAD (TabletGarage) - defined with host 192.168.0.116 on port 8090 and AccessPoint-SSID dlink-D22C
2016.04.10 17:07:20 3: AMAD (AMADCommBridge) - defined Bridge with Socketport 8090
2016.04.10 17:07:20 3: AMAD (AMADCommBridge) - Attention!!! By the first run, dont forget to "set AMADCommBridge fhemServerIP <IP-FHEM>"
2016.04.10 17:07:20 3: AMADCommBridge: port 8090 opened
2016.04.10 17:07:20 1: Including ./log/fhem.save
2016.04.10 17:07:20 3: EMONITOR_InitSingle: found new AbstellraumHZ with type CUL_HM
2016.04.10 17:07:20 2: EMONITOR_InitSingle: Warning device AbstellraumHZ rd energy energy 0 !
2016.04.10 17:07:20 3: EMONITOR_InitSingle: found new Gartenbeleuchtung with type FS20
2016.04.10 17:07:20 3: EMONITOR_InitSingle: found new PoolPumpe with type CUL_HM
2016.04.10 17:07:20 2: EMONITOR_InitSingle: Warning device PoolPumpe rd energy energy 0 !
2016.04.10 17:07:20 3: EMONITOR_InitSingle: found new Poolbeleuchtung with type FS20
2016.04.10 17:07:20 3: EMONITOR_InitSingle: found new Roboter_sw4 with type CUL_HM
2016.04.10 17:07:20 2: EMONITOR_InitSingle: Warning device Roboter_sw4 rd energy energy 0 !
2016.04.10 17:07:20 3: EMONITOR_InitSingle: found new SolarPumpe with type CUL_HM
2016.04.10 17:07:20 2: EMONITOR_InitSingle: Warning device SolarPumpe rd energy energy 0 !
2016.04.10 17:07:20 3: EMONITOR_Init2: found 6 devices
2016.04.10 17:07:20 3: myOWServer: Opening connection to OWServer localhost:4304...
2016.04.10 17:07:20 3: myOWServer: Successfully connected to localhost:4304.
2016.04.10 17:07:22 1: HMLAN_Parse: HMUSB new condition ok
2016.04.10 17:07:25 3: Device GaragenTor added to ActionDetector with 028:00 time
2016.04.10 17:07:27 3: CUL_HM set PoolPumpe statusRequest
2016.04.10 17:07:28 3: CUL_HM set SolarPumpe statusRequest
2016.04.10 17:07:29 3: CUL_HM set AbstellraumHZ statusRequest
2016.04.10 17:07:30 3: CUL_HM set Roboter_sw4 statusRequest
2016.04.10 17:07:34 0: HourCounter CN.Roboter_sw4 Run.598 first run done countsOverall:2
2016.04.10 17:07:34 0: HourCounter CN.AbstellraumHZ Run.598 first run done countsOverall:1
2016.04.10 17:07:34 0: HourCounter CN.Poolbeleuchtung Run.598 first run done countsOverall:2
2016.04.10 17:07:34 0: HourCounter CN.SolarPumpe Run.598 first run done countsOverall:10
2016.04.10 17:07:34 0: HourCounter CN.Gartenbeleuchtung Run.598 first run done countsOverall:14
2016.04.10 17:07:34 0: HourCounter CN.PoolPumpe Run.598 first run done countsOverall:18
2016.04.10 17:07:35 5: AMAD (TabletGarage) - Send statusRequest with URL: "http://192.168.0.116:8090/fhem-amad/deviceInfo/" and Header: "fhemIP: 192.168.0.117
fhemDevice: TabletGarage
activeTask: none
apSSID: dlink-D22C"
2016.04.10 17:07:49 3: EMONITOR_Init2: found 6 devices
2016.04.10 17:08:27 5: AMAD (TabletGarage) - set TabletGarage statusRequest
2016.04.10 17:08:27 5: AMAD (TabletGarage) - Send statusRequest with URL: "http://192.168.0.116:8090/fhem-amad/deviceInfo/" and Header: "fhemIP: 192.168.0.117
fhemDevice: TabletGarage
activeTask: none
apSSID: dlink-D22C"

jump to the top


Habe nach einem StatusRequest jetzt am Tablet Modul 1.2
Informations and SetCommands  "ROT" gehabt!
System1 fhem 6.1 auf RPi 4B mit 4GB, HMUSBConfig, DS9490R-1Wire, Busware USB 868, Pool-Solarsteuerung mit FHEM. System2 fhem 6.1 auf RPi 4B mit 4GB (Bullseye) mit Busware USB 868 und 433 und HMUARTLGW für Haussteuerung

https://www.flickr.com/photos/canonhelmi/

CoolTux

#5
10 April 2016, 17:20:41
Zitat von: Helmi55 am 10 April 2016, 17:10:27
Servus
hier nochmals hoffentlich mit mehr Info für dich
Code Auswählen


Save config
MAIN
Tablet-UI
Tablet-EVAL
Favoriten
Abstellraum
Brunnen
Garage
Garten
Poolsteuerung
AMAD
Energie
Logs
Plots
Statistik
System
Unsorted
Wetter
icoEverything Everything
Logfile
Commandref
Remote doc
Edit files
Select style
Event monitor
updatecheck
update
restart
reread

jump to the end

2016.04.10 17:05:33 3: [UtilsHourCounter] Init Done with Version 1.0.1.0 - 10.12.2014 (john)
Subroutine UtilsHourCounter_Initialize redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 45.
Subroutine appHC_OnYear redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 55.
Subroutine appHC_OnMonth redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 80.
Subroutine appHC_OnWeek redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 104.
Subroutine appHC_OnDay redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 128.
Subroutine appHC_OnHour redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 167.
Subroutine appHC_OnCount redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 184.
Subroutine appHCNotify redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 249.
2016.04.10 17:05:33 1: Including fhem.cfg
Subroutine UtilsHourCounter_Initialize redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 45, <$fh> line 8.
Subroutine appHC_OnYear redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 55, <$fh> line 8.
Subroutine appHC_OnMonth redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 80, <$fh> line 8.
Subroutine appHC_OnWeek redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 104, <$fh> line 8.
Subroutine appHC_OnDay redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 128, <$fh> line 8.
Subroutine appHC_OnHour redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 167, <$fh> line 8.
Subroutine appHC_OnCount redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 184, <$fh> line 8.
Subroutine appHC_OnValueChanged redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 219, <$fh> line 8.
Subroutine appHCNotify redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 249, <$fh> line 8.
2016.04.10 17:05:33 3: telnetPort: port 7072 opened
2016.04.10 17:05:34 3: WEB: port 8083 opened
2016.04.10 17:05:34 3: WEBphone: port 8084 opened
2016.04.10 17:05:34 3: WEBtablet: port 8085 opened
2016.04.10 17:05:34 2: eventTypes: loaded 958 events from ./log/eventTypes.txt
2016.04.10 17:05:34 3: Opening CUL_0 device /dev/ttyACM0
2016.04.10 17:05:34 3: Setting CUL_0 serial parameters to 9600,8,N,1
2016.04.10 17:05:34 3: CUL_0 device opened
2016.04.10 17:05:35 3: CUL_0: Possible commands: BbCFiAZEGMKUYRTVWXefmltux
2016.04.10 17:05:35 1: HMLAN_Parse: HMUSB new condition disconnected
2016.04.10 17:05:35 3: Opening HMUSB device 127.0.0.1:1234
2016.04.10 17:05:35 3: HMUSB device opened
2016.04.10 17:05:35 1: HMLAN_Parse: HMUSB new condition init
2016.04.10 17:05:35 3: TABLETUI: new ext defined infix:ftui/: dir:./www/tablet:
2016.04.10 17:05:35 3: Registering HTTPSRV TABLETUI for URL /ftui   and assigned link ftui/ ...
2016.04.10 17:05:35 3: TABLETUIEVAL: new ext defined infix:ftui_eval/: dir:./www/tablet_eval:
2016.04.10 17:05:35 3: Registering HTTPSRV TABLETUIEVAL for URL /ftui_eval   and assigned link ftui_eval/ ...
2016.04.10 17:05:37 3: HourCounter HourCounter Initialize.220 Init Done with Version 1.0.1.2 - 24.12.2014
2016.04.10 17:05:37 0: HourCounter CN.SolarPumpe Define.228 parameters: CN.SolarPumpe HourCounter SolarPumpe:on SolarPumpe:off
2016.04.10 17:05:37 0: HourCounter CN.PoolPumpe Define.228 parameters: CN.PoolPumpe HourCounter PoolPumpe:on PoolPumpe:off
2016.04.10 17:05:37 0: HourCounter CN.Roboter_sw4 Define.228 parameters: CN.Roboter_sw4 HourCounter Roboter_sw4:on Roboter_sw4:off
2016.04.10 17:05:37 0: HourCounter CN.AbstellraumHZ Define.228 parameters: CN.AbstellraumHZ HourCounter AbstellraumHZ:on AbstellraumHZ:off
2016.04.10 17:05:37 0: HourCounter CN.Gartenbeleuchtung Define.228 parameters: CN.Gartenbeleuchtung HourCounter Gartenbeleuchtung:on Gartenbeleuchtung:off
2016.04.10 17:05:37 0: HourCounter CN.Poolbeleuchtung Define.228 parameters: CN.Poolbeleuchtung HourCounter Poolbeleuchtung:on Poolbeleuchtung:off
Constant subroutine main::URL redefined at /usr/share/perl/5.14/constant.pm line 136, <$fh> line 709.
2016.04.10 17:05:37 3: [Daemmerung] 0 attempt(s) needed to get valid weather data from yahoo
2016.04.10 17:05:38 3: AMAD (TabletGarage) - defined with host 192.168.0.116 on port 8090 and AccessPoint-SSID dlink-D22C
2016.04.10 17:05:38 3: AMAD (AMADCommBridge) - defined Bridge with Socketport 8090
2016.04.10 17:05:38 3: AMAD (AMADCommBridge) - Attention!!! By the first run, dont forget to "set AMADCommBridge fhemServerIP <IP-FHEM>"
2016.04.10 17:05:38 3: AMADCommBridge: port 8090 opened
2016.04.10 17:05:38 1: Including ./log/fhem.save
2016.04.10 17:05:38 3: Device GaragenTor added to ActionDetector with 028:00 time
2016.04.10 17:05:38 3: EMONITOR_InitSingle: found new AbstellraumHZ with type CUL_HM
2016.04.10 17:05:38 2: EMONITOR_InitSingle: Warning device AbstellraumHZ rd energy energy 0 !
2016.04.10 17:05:38 3: EMONITOR_InitSingle: found new Gartenbeleuchtung with type FS20
2016.04.10 17:05:38 3: EMONITOR_InitSingle: found new PoolPumpe with type CUL_HM
2016.04.10 17:05:38 2: EMONITOR_InitSingle: Warning device PoolPumpe rd energy energy 0 !
2016.04.10 17:05:38 3: EMONITOR_InitSingle: found new Poolbeleuchtung with type FS20
2016.04.10 17:05:38 3: EMONITOR_InitSingle: found new Roboter_sw4 with type CUL_HM
2016.04.10 17:05:38 2: EMONITOR_InitSingle: Warning device Roboter_sw4 rd energy energy 0 !
2016.04.10 17:05:38 3: EMONITOR_InitSingle: found new SolarPumpe with type CUL_HM
2016.04.10 17:05:38 2: EMONITOR_InitSingle: Warning device SolarPumpe rd energy energy 0 !
2016.04.10 17:05:38 3: EMONITOR_Init2: found 6 devices
2016.04.10 17:05:39 1: usb create starting
2016.04.10 17:05:39 3: Probing CUL device /dev/ttyAMA0
2016.04.10 17:05:39 3: Probing TCM_ESP3 device /dev/ttyAMA0
2016.04.10 17:05:40 3: Probing FRM device /dev/ttyAMA0
2016.04.10 17:05:45 1: usb create end
2016.04.10 17:05:45 3: myOWServer: Opening connection to OWServer localhost:4304...
2016.04.10 17:05:45 3: myOWServer: Successfully connected to localhost:4304.
2016.04.10 17:05:47 2: SecurityCheck:  telnetPort has no associated allowed device with password/globalpassword.  Restart FHEM for a new check if the problem is fixed, or set the global attribute motd to none to supress this message.
2016.04.10 17:05:47 0: Featurelevel: 5.7
2016.04.10 17:05:47 0: Server started with 152 defined entities (fhem.pl:11191/2016-04-05 perl:5.014002 os:linux user:fhem pid:28041)
2016.04.10 17:05:47 3: CUL_HM set PoolPumpe statusRequest
2016.04.10 17:05:50 1: HMLAN_Parse: HMUSB new condition ok
2016.04.10 17:05:52 3: CUL_HM set SolarPumpe statusRequest
2016.04.10 17:05:53 0: HourCounter CN.AbstellraumHZ Run.598 first run done countsOverall:1
2016.04.10 17:05:53 0: HourCounter CN.SolarPumpe Run.598 first run done countsOverall:10
2016.04.10 17:05:53 0: HourCounter CN.Roboter_sw4 Run.598 first run done countsOverall:2
2016.04.10 17:05:53 0: HourCounter CN.Gartenbeleuchtung Run.598 first run done countsOverall:14
2016.04.10 17:05:53 0: HourCounter CN.Poolbeleuchtung Run.598 first run done countsOverall:2
2016.04.10 17:05:54 0: HourCounter CN.PoolPumpe Run.598 first run done countsOverall:18
2016.04.10 17:05:54 5: AMAD (TabletGarage) - Send statusRequest with URL: "http://192.168.0.116:8090/fhem-amad/deviceInfo/" and Header: "fhemIP: 192.168.0.117
fhemDevice: TabletGarage
activeTask: none
apSSID: dlink-D22C"
2016.04.10 17:05:54 3: CUL_HM set AbstellraumHZ statusRequest
2016.04.10 17:05:55 3: CUL_HM set Roboter_sw4 statusRequest
2016.04.10 17:06:07 3: EMONITOR_Init2: found 6 devices
2016.04.10 17:06:32 5: AMAD (TabletGarage) - set TabletGarage statusRequest
2016.04.10 17:06:32 5: AMAD (TabletGarage) - Send statusRequest with URL: "http://192.168.0.116:8090/fhem-amad/deviceInfo/" and Header: "fhemIP: 192.168.0.117
fhemDevice: TabletGarage
activeTask: none
apSSID: dlink-D22C"
2016.04.10 17:07:13 3: AMAD (TabletGarage) - defined with host 192.168.0.116 on port 8090 and AccessPoint-SSID dlink-D22C
2016.04.10 17:07:18 3: HourCounter CN.Poolbeleuchtung Undef.272 Done
2016.04.10 17:07:18 3: HourCounter CN.Gartenbeleuchtung Undef.272 Done
2016.04.10 17:07:18 3: HourCounter CN.AbstellraumHZ Undef.272 Done
2016.04.10 17:07:18 3: HourCounter CN.Roboter_sw4 Undef.272 Done
2016.04.10 17:07:18 3: HourCounter CN.PoolPumpe Undef.272 Done
2016.04.10 17:07:18 3: HourCounter CN.SolarPumpe Undef.272 Done
2016.04.10 17:07:18 3: Unregistering HTTPSRV TABLETUIEVAL for URL /ftui_eval...
2016.04.10 17:07:18 3: Unregistering HTTPSRV TABLETUI for URL /ftui...
2016.04.10 17:07:18 1: PERL WARNING: Subroutine UtilsHourCounter_Initialize redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 45.
2016.04.10 17:07:18 1: PERL WARNING: Subroutine appHC_OnYear redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 55.
2016.04.10 17:07:18 1: PERL WARNING: Subroutine appHC_OnMonth redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 80.
2016.04.10 17:07:18 1: PERL WARNING: Subroutine appHC_OnWeek redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 104.
2016.04.10 17:07:18 1: PERL WARNING: Subroutine appHC_OnDay redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 128.
2016.04.10 17:07:18 1: PERL WARNING: Subroutine appHC_OnHour redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 167.
2016.04.10 17:07:18 1: PERL WARNING: Subroutine appHC_OnCount redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 184.
2016.04.10 17:07:18 1: PERL WARNING: Subroutine appHC_OnValueChanged redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 219.
2016.04.10 17:07:18 1: PERL WARNING: Subroutine appHCNotify redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 249.
2016.04.10 17:07:18 1: Including fhem.cfg
2016.04.10 17:07:18 1: PERL WARNING: Subroutine UtilsHourCounter_Initialize redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 45, <$fh> line 8.
2016.04.10 17:07:18 1: PERL WARNING: Subroutine appHC_OnYear redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 55, <$fh> line 8.
2016.04.10 17:07:18 1: PERL WARNING: Subroutine appHC_OnMonth redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 80, <$fh> line 8.
2016.04.10 17:07:18 1: PERL WARNING: Subroutine appHC_OnWeek redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 104, <$fh> line 8.
2016.04.10 17:07:18 1: PERL WARNING: Subroutine appHC_OnDay redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 128, <$fh> line 8.
2016.04.10 17:07:18 1: PERL WARNING: Subroutine appHC_OnHour redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 167, <$fh> line 8.
2016.04.10 17:07:18 1: PERL WARNING: Subroutine appHC_OnCount redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 184, <$fh> line 8.
2016.04.10 17:07:18 1: PERL WARNING: Subroutine appHC_OnValueChanged redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 219, <$fh> line 8.
2016.04.10 17:07:18 1: PERL WARNING: Subroutine appHCNotify redefined at ./FHEM/99_UtilsHourCounter_CE.pm line 249, <$fh> line 8.
2016.04.10 17:07:18 3: telnetPort: port 7072 opened
2016.04.10 17:07:18 3: WEB: port 8083 opened
2016.04.10 17:07:18 3: WEBphone: port 8084 opened
2016.04.10 17:07:18 3: WEBtablet: port 8085 opened
2016.04.10 17:07:18 2: eventTypes: loaded 958 events from ./log/eventTypes.txt
2016.04.10 17:07:18 3: Opening CUL_0 device /dev/ttyACM0
2016.04.10 17:07:18 3: Setting CUL_0 serial parameters to 9600,8,N,1
2016.04.10 17:07:18 3: CUL_0 device opened
2016.04.10 17:07:18 3: CUL_0: Possible commands: BbCFiAZEGMKUYRTVWXefmltux
2016.04.10 17:07:19 1: HMLAN_Parse: HMUSB new condition disconnected
2016.04.10 17:07:19 3: Opening HMUSB device 127.0.0.1:1234
2016.04.10 17:07:19 3: HMUSB device opened
2016.04.10 17:07:19 1: HMLAN_Parse: HMUSB new condition init
2016.04.10 17:07:19 3: TABLETUI: new ext defined infix:ftui/: dir:./www/tablet:
2016.04.10 17:07:19 3: Registering HTTPSRV TABLETUI for URL /ftui   and assigned link ftui/ ...
2016.04.10 17:07:19 3: TABLETUIEVAL: new ext defined infix:ftui_eval/: dir:./www/tablet_eval:
2016.04.10 17:07:19 3: Registering HTTPSRV TABLETUIEVAL for URL /ftui_eval   and assigned link ftui_eval/ ...
2016.04.10 17:07:19 0: HourCounter CN.SolarPumpe Define.228 parameters: CN.SolarPumpe HourCounter SolarPumpe:on SolarPumpe:off
2016.04.10 17:07:19 0: HourCounter CN.PoolPumpe Define.228 parameters: CN.PoolPumpe HourCounter PoolPumpe:on PoolPumpe:off
2016.04.10 17:07:19 0: HourCounter CN.Roboter_sw4 Define.228 parameters: CN.Roboter_sw4 HourCounter Roboter_sw4:on Roboter_sw4:off
2016.04.10 17:07:19 0: HourCounter CN.AbstellraumHZ Define.228 parameters: CN.AbstellraumHZ HourCounter AbstellraumHZ:on AbstellraumHZ:off
2016.04.10 17:07:19 0: HourCounter CN.Gartenbeleuchtung Define.228 parameters: CN.Gartenbeleuchtung HourCounter Gartenbeleuchtung:on Gartenbeleuchtung:off
2016.04.10 17:07:19 0: HourCounter CN.Poolbeleuchtung Define.228 parameters: CN.Poolbeleuchtung HourCounter Poolbeleuchtung:on Poolbeleuchtung:off
2016.04.10 17:07:19 3: [Daemmerung] 0 attempt(s) needed to get valid weather data from yahoo
2016.04.10 17:07:20 3: AMAD (TabletGarage) - defined with host 192.168.0.116 on port 8090 and AccessPoint-SSID dlink-D22C
2016.04.10 17:07:20 3: AMAD (AMADCommBridge) - defined Bridge with Socketport 8090
2016.04.10 17:07:20 3: AMAD (AMADCommBridge) - Attention!!! By the first run, dont forget to "set AMADCommBridge fhemServerIP <IP-FHEM>"
2016.04.10 17:07:20 3: AMADCommBridge: port 8090 opened
2016.04.10 17:07:20 1: Including ./log/fhem.save
2016.04.10 17:07:20 3: EMONITOR_InitSingle: found new AbstellraumHZ with type CUL_HM
2016.04.10 17:07:20 2: EMONITOR_InitSingle: Warning device AbstellraumHZ rd energy energy 0 !
2016.04.10 17:07:20 3: EMONITOR_InitSingle: found new Gartenbeleuchtung with type FS20
2016.04.10 17:07:20 3: EMONITOR_InitSingle: found new PoolPumpe with type CUL_HM
2016.04.10 17:07:20 2: EMONITOR_InitSingle: Warning device PoolPumpe rd energy energy 0 !
2016.04.10 17:07:20 3: EMONITOR_InitSingle: found new Poolbeleuchtung with type FS20
2016.04.10 17:07:20 3: EMONITOR_InitSingle: found new Roboter_sw4 with type CUL_HM
2016.04.10 17:07:20 2: EMONITOR_InitSingle: Warning device Roboter_sw4 rd energy energy 0 !
2016.04.10 17:07:20 3: EMONITOR_InitSingle: found new SolarPumpe with type CUL_HM
2016.04.10 17:07:20 2: EMONITOR_InitSingle: Warning device SolarPumpe rd energy energy 0 !
2016.04.10 17:07:20 3: EMONITOR_Init2: found 6 devices
2016.04.10 17:07:20 3: myOWServer: Opening connection to OWServer localhost:4304...
2016.04.10 17:07:20 3: myOWServer: Successfully connected to localhost:4304.
2016.04.10 17:07:22 1: HMLAN_Parse: HMUSB new condition ok
2016.04.10 17:07:25 3: Device GaragenTor added to ActionDetector with 028:00 time
2016.04.10 17:07:27 3: CUL_HM set PoolPumpe statusRequest
2016.04.10 17:07:28 3: CUL_HM set SolarPumpe statusRequest
2016.04.10 17:07:29 3: CUL_HM set AbstellraumHZ statusRequest
2016.04.10 17:07:30 3: CUL_HM set Roboter_sw4 statusRequest
2016.04.10 17:07:34 0: HourCounter CN.Roboter_sw4 Run.598 first run done countsOverall:2
2016.04.10 17:07:34 0: HourCounter CN.AbstellraumHZ Run.598 first run done countsOverall:1
2016.04.10 17:07:34 0: HourCounter CN.Poolbeleuchtung Run.598 first run done countsOverall:2
2016.04.10 17:07:34 0: HourCounter CN.SolarPumpe Run.598 first run done countsOverall:10
2016.04.10 17:07:34 0: HourCounter CN.Gartenbeleuchtung Run.598 first run done countsOverall:14
2016.04.10 17:07:34 0: HourCounter CN.PoolPumpe Run.598 first run done countsOverall:18
2016.04.10 17:07:35 5: AMAD (TabletGarage) - Send statusRequest with URL: "http://192.168.0.116:8090/fhem-amad/deviceInfo/" and Header: "fhemIP: 192.168.0.117
fhemDevice: TabletGarage
activeTask: none
apSSID: dlink-D22C"
2016.04.10 17:07:49 3: EMONITOR_Init2: found 6 devices
2016.04.10 17:08:27 5: AMAD (TabletGarage) - set TabletGarage statusRequest
2016.04.10 17:08:27 5: AMAD (TabletGarage) - Send statusRequest with URL: "http://192.168.0.116:8090/fhem-amad/deviceInfo/" and Header: "fhemIP: 192.168.0.117
fhemDevice: TabletGarage
activeTask: none
apSSID: dlink-D22C"

jump to the top


Habe nach einem StatusRequest jetzt am Tablet Modul 1.2
Informations and SetCommands  "ROT" gehabt!

Äh was bedeutet für Dich Tablet Modul 1.2?
Ich hoffe doch nicht das Du das alte Flowset gelassen hast?
Du musst nicht wissen wie es geht! Du musst nur wissen wo es steht, wie es geht.
Support me to buy new test hardware for development: https://www.paypal.com/paypalme/MOldenburg
My FHEM Git: https://git.cooltux.net/FHEM/
Das TuxNet Wiki:
https://www.cooltux.net

Helmi55

#6
10 April 2016, 17:43:34
Sorry ich bin ein Depp - stehe tief in deiner Schuld.
Ich habe die Version 1.2 in die Dropbox zum Syncen geladen statt der 2.0
DAs war insgesamt gesehen nicht mein Wochenende - hoffe ich kann jetzt noch die Kaffeemaschine bedienen.

Nochmals sorry und einen schönen Sonntag noch
Gruß
Helmut
System1 fhem 6.1 auf RPi 4B mit 4GB, HMUSBConfig, DS9490R-1Wire, Busware USB 868, Pool-Solarsteuerung mit FHEM. System2 fhem 6.1 auf RPi 4B mit 4GB (Bullseye) mit Busware USB 868 und 433 und HMUARTLGW für Haussteuerung

https://www.flickr.com/photos/canonhelmi/

Tommy82

#7
10 April 2016, 18:05:47 Letzte Bearbeitung: 10 April 2016, 18:12:22 von Tommy82
Hi,
ich hab auch das Problem das die readings nicht aktualisiert werden, obwohl ich das Flowset 2.0 aktiv habe, trotzdem werden seit gestern abend (manueller statusRequest) keine readings aktualisiert, hab das ganze jetzt mal auf verbose 5 geloggt, und einen manuellen statusRequest durchgeführt.
Code Auswählen
2016.04.10 18:01:56.037 5: AMAD (Android_Tablett_Wohnzimmer) - set Android_Tablett_Wohnzimmer statusRequest
2016.04.10 18:01:56.042 5: AMAD (Android_Tablett_Wohnzimmer) - Send statusRequest with URL: "http://192.168.188.23:8090/fhem-amad/deviceInfo/" and Header: "fhemIP: 192.168.188.47
fhemDevice: Android_Tablett_Wohnzimmer
activeTask: none
apSSID: T&T,T&T5GHZ"
2016.04.10 18:01:59.837 5: AMAD (AMADCommBridge) - Receive RAW Message in Debugging Mode: POST / HTTP/1.1
Content-Type: text/plain
User-Agent: Mozilla/5.0 (compatible; Automagic)
FHEMDEVICE: Android_Tablett_Wohnzimmer
FHEMCMD: setreading
Host: 192.168.188.47:8090
Connection: Keep-Alive
Accept-Encoding: gzip
Content-Length: 25

volumeNotification@@0@@@@
2016.04.10 18:01:59.838 4: AMAD (AMADCommBridge) - AMAD_CommBridge: processing receive reading values - Device: Android_Tablett_Wohnzimmer Data: volumeNotification@@0@@@@
2016.04.10 18:01:59.839 5: AMAD (Android_Tablett_Wohnzimmer) - Processing data: volumeNotification@@0@@@@
2016.04.10 18:01:59.915 5: AMAD (AMADCommBridge) - Receive RAW Message in Debugging Mode: POST / HTTP/1.1
Content-Type: text/plain
User-Agent: Mozilla/5.0 (compatible; Automagic)
FHEMDEVICE: Android_Tablett_Wohnzimmer
FHEMCMD: setreading
Host: 192.168.188.47:8090
Connection: Keep-Alive
Accept-Encoding: gzip
Content-Length: 46

androidVersion@@4.2 - 4.2.2 Jelly Bean MR1@@@@
2016.04.10 18:01:59.916 4: AMAD (AMADCommBridge) - AMAD_CommBridge: processing receive reading values - Device: Android_Tablett_Wohnzimmer Data: androidVersion@@4.2 - 4.2.2 Jelly Bean MR1@@@@
2016.04.10 18:01:59.916 5: AMAD (Android_Tablett_Wohnzimmer) - Processing data: androidVersion@@4.2 - 4.2.2 Jelly Bean MR1@@@@
2016.04.10 18:01:59.978 5: AMAD (AMADCommBridge) - Receive RAW Message in Debugging Mode: POST / HTTP/1.1
Content-Type: text/plain
User-Agent: Mozilla/5.0 (compatible; Automagic)
FHEMDEVICE: Android_Tablett_Wohnzimmer
FHEMCMD: setreading
Host: 192.168.188.47:8090
Connection: Keep-Alive
Accept-Encoding: gzip
Content-Length: 25

screenBrightness@@157@@@@
2016.04.10 18:01:59.979 4: AMAD (AMADCommBridge) - AMAD_CommBridge: processing receive reading values - Device: Android_Tablett_Wohnzimmer Data: screenBrightness@@157@@@@
2016.04.10 18:01:59.980 5: AMAD (Android_Tablett_Wohnzimmer) - Processing data: screenBrightness@@157@@@@
2016.04.10 18:02:00.048 5: AMAD (AMADCommBridge) - Receive RAW Message in Debugging Mode: POST / HTTP/1.1
Content-Type: text/plain
User-Agent: Mozilla/5.0 (compatible; Automagic)
FHEMDEVICE: Android_Tablett_Wohnzimmer
FHEMCMD: setreading
Host: 192.168.188.47:8090
Connection: Keep-Alive
Accept-Encoding: gzip
Content-Length: 40

powerLevel@@100.0@@@@powerPlugged@@1@@@@
2016.04.10 18:02:00.049 4: AMAD (AMADCommBridge) - AMAD_CommBridge: processing receive reading values - Device: Android_Tablett_Wohnzimmer Data: powerLevel@@100.0@@@@powerPlugged@@1@@@@
2016.04.10 18:02:00.049 5: AMAD (Android_Tablett_Wohnzimmer) - Processing data: powerLevel@@100.0@@@@powerPlugged@@1@@@@
2016.04.10 18:02:00.092 2: IT set Steckdose_Tablet off
2016.04.10 18:02:00.893 5: AMAD (AMADCommBridge) - Receive RAW Message in Debugging Mode: POST / HTTP/1.1
Content-Type: text/plain
User-Agent: Mozilla/5.0 (compatible; Automagic)
FHEMDEVICE: Android_Tablett_Wohnzimmer
FHEMCMD: setreading
Host: 192.168.188.47:8090
Connection: Keep-Alive
Accept-Encoding: gzip
Content-Length: 45

nextAlarmTime@@null@@@@nextAlarmDay@@null@@@@
2016.04.10 18:02:00.894 4: AMAD (AMADCommBridge) - AMAD_CommBridge: processing receive reading values - Device: Android_Tablett_Wohnzimmer Data: nextAlarmTime@@null@@@@nextAlarmDay@@null@@@@
2016.04.10 18:02:00.895 5: AMAD (Android_Tablett_Wohnzimmer) - Processing data: nextAlarmTime@@null@@@@nextAlarmDay@@null@@@@
2016.04.10 18:02:00.978 5: AMAD (AMADCommBridge) - Receive RAW Message in Debugging Mode: POST / HTTP/1.1
Content-Type: text/plain
User-Agent: Mozilla/5.0 (compatible; Automagic)
FHEMDEVICE: Android_Tablett_Wohnzimmer
FHEMCMD: setreading
Host: 192.168.188.47:8090
Connection: Keep-Alive
Accept-Encoding: gzip
Content-Length: 17

bluetooth@@on@@@@
2016.04.10 18:02:00.979 4: AMAD (AMADCommBridge) - AMAD_CommBridge: processing receive reading values - Device: Android_Tablett_Wohnzimmer Data: bluetooth@@on@@@@
2016.04.10 18:02:00.980 5: AMAD (Android_Tablett_Wohnzimmer) - Processing data: bluetooth@@on@@@@
2016.04.10 18:02:01.041 5: AMAD (AMADCommBridge) - Receive RAW Message in Debugging Mode: POST / HTTP/1.1
Content-Type: text/plain
User-Agent: Mozilla/5.0 (compatible; Automagic)
FHEMDEVICE: Android_Tablett_Wohnzimmer
FHEMCMD: setreading
Host: 192.168.188.47:8090
Connection: Keep-Alive
Accept-Encoding: gzip
Content-Length: 45

nextAlarmTime@@null@@@@nextAlarmDay@@null@@@@
2016.04.10 18:02:01.042 4: AMAD (AMADCommBridge) - AMAD_CommBridge: processing receive reading values - Device: Android_Tablett_Wohnzimmer Data: nextAlarmTime@@null@@@@nextAlarmDay@@null@@@@
2016.04.10 18:02:01.042 5: AMAD (Android_Tablett_Wohnzimmer) - Processing data: nextAlarmTime@@null@@@@nextAlarmDay@@null@@@@
2016.04.10 18:02:01.109 5: AMAD (AMADCommBridge) - Receive RAW Message in Debugging Mode: POST / HTTP/1.1
Content-Type: text/plain
User-Agent: Mozilla/5.0 (compatible; Automagic)
FHEMDEVICE: Android_Tablett_Wohnzimmer
FHEMCMD: setreading
Host: 192.168.188.47:8090
Connection: Keep-Alive
Accept-Encoding: gzip
Content-Length: 26

dockingState@@undocked@@@@
2016.04.10 18:02:01.110 4: AMAD (AMADCommBridge) - AMAD_CommBridge: processing receive reading values - Device: Android_Tablett_Wohnzimmer Data: dockingState@@undocked@@@@
2016.04.10 18:02:01.111 5: AMAD (Android_Tablett_Wohnzimmer) - Processing data: dockingState@@undocked@@@@
2016.04.10 18:02:01.173 4: Connection accepted from AMADCommBridge_192.168.188.23_59983
2016.04.10 18:02:01.176 5: AMAD (AMADCommBridge) - Receive RAW Message in Debugging Mode: POST / HTTP/1.1
Content-Type: text/plain
User-Agent: Mozilla/5.0 (compatible; Automagic)
FHEMDEVICE: Android_Tablett_Wohnzimmer
FHEMCMD: setreading
Host: 192.168.188.47:8090
Connection: Keep-Alive
Accept-Encoding: gzip
Content-Length: 130

currentMusicTrack@@no soundplayer activ@@@@currentMusicAlbum@@no soundplayer activ@@@@currentMusicArtist@@no soundplayer activ@@@@
2016.04.10 18:02:01.177 4: AMAD (AMADCommBridge) - AMAD_CommBridge: processing receive reading values - Device: Android_Tablett_Wohnzimmer Data: currentMusicTrack@@no soundplayer activ@@@@currentMusicAlbum@@no soundplayer activ@@@@currentMusicArtist@@no soundplayer activ@@@@
2016.04.10 18:02:01.177 5: AMAD (Android_Tablett_Wohnzimmer) - Processing data: currentMusicTrack@@no soundplayer activ@@@@currentMusicAlbum@@no soundplayer activ@@@@currentMusicArtist@@no soundplayer activ@@@@
2016.04.10 18:02:01.258 4: Connection accepted from AMADCommBridge_192.168.188.23_53506
2016.04.10 18:02:01.259 5: AMAD (AMADCommBridge) - Receive RAW Message in Debugging Mode: POST / HTTP/1.1
Content-Type: text/plain
User-Agent: Mozilla/5.0 (compatible; Automagic)
FHEMDEVICE: Android_Tablett_Wohnzimmer
FHEMCMD: setreading
Host: 192.168.188.47:8090
Connection: Keep-Alive
Accept-Encoding: gzip
Content-Length: 18

keyguardSet@@0@@@@
2016.04.10 18:02:01.260 4: AMAD (AMADCommBridge) - AMAD_CommBridge: processing receive reading values - Device: Android_Tablett_Wohnzimmer Data: keyguardSet@@0@@@@
2016.04.10 18:02:01.260 5: AMAD (Android_Tablett_Wohnzimmer) - Processing data: keyguardSet@@0@@@@
2016.04.10 18:02:01.324 5: AMAD (AMADCommBridge) - Receive RAW Message in Debugging Mode: POST / HTTP/1.1
Content-Type: text/plain
User-Agent: Mozilla/5.0 (compatible; Automagic)
FHEMDEVICE: Android_Tablett_Wohnzimmer
FHEMCMD: setreading
Host: 192.168.188.47:8090
Connection: Keep-Alive
Accept-Encoding: gzip
Content-Length: 50

automagicState@@not supported from your device@@@@
2016.04.10 18:02:01.325 4: AMAD (AMADCommBridge) - AMAD_CommBridge: processing receive reading values - Device: Android_Tablett_Wohnzimmer Data: automagicState@@not supported from your device@@@@
2016.04.10 18:02:01.325 5: AMAD (Android_Tablett_Wohnzimmer) - Processing data: automagicState@@not supported from your device@@@@
2016.04.10 18:02:01.389 4: Connection accepted from AMADCommBridge_192.168.188.23_47384
2016.04.10 18:02:01.394 5: AMAD (AMADCommBridge) - Receive RAW Message in Debugging Mode: POST / HTTP/1.1
Content-Type: text/plain
User-Agent: Mozilla/5.0 (compatible; Automagic)
FHEMDEVICE: Android_Tablett_Wohnzimmer
FHEMCMD: setreading
Host: 192.168.188.47:8090
Connection: Keep-Alive
Accept-Encoding: gzip
Content-Length: 59

connectedBTdevices@@null@@@@connectedBTdevicesMAC@@null@@@@
2016.04.10 18:02:01.395 4: AMAD (AMADCommBridge) - AMAD_CommBridge: processing receive reading values - Device: Android_Tablett_Wohnzimmer Data: connectedBTdevices@@null@@@@connectedBTdevicesMAC@@null@@@@
2016.04.10 18:02:01.395 5: AMAD (Android_Tablett_Wohnzimmer) - Processing data: connectedBTdevices@@null@@@@connectedBTdevicesMAC@@null@@@@
2016.04.10 18:02:01.504 5: AMAD (AMADCommBridge) - Receive RAW Message in Debugging Mode: POST / HTTP/1.1
Content-Type: text/plain
User-Agent: Mozilla/5.0 (compatible; Automagic)
FHEMDEVICE: Android_Tablett_Wohnzimmer
FHEMCMD: setreading
Host: 192.168.188.47:8090
Connection: Keep-Alive
Accept-Encoding: gzip
Content-Length: 13

volume@@0@@@@
2016.04.10 18:02:01.507 4: AMAD (AMADCommBridge) - AMAD_CommBridge: processing receive reading values - Device: Android_Tablett_Wohnzimmer Data: volume@@0@@@@
2016.04.10 18:02:01.508 5: AMAD (Android_Tablett_Wohnzimmer) - Processing data: volume@@0@@@@
2016.04.10 18:02:01.728 5: AMAD (AMADCommBridge) - Receive RAW Message in Debugging Mode: POST / HTTP/1.1
Content-Type: text/plain
User-Agent: Mozilla/5.0 (compatible; Automagic)
FHEMDEVICE: Android_Tablett_Wohnzimmer
FHEMCMD: setreading
Host: 192.168.188.47:8090
Connection: Keep-Alive
Accept-Encoding: gzip
Content-Length: 13

volume@@0@@@@
2016.04.10 18:02:01.730 4: AMAD (AMADCommBridge) - AMAD_CommBridge: processing receive reading values - Device: Android_Tablett_Wohnzimmer Data: volume@@0@@@@
2016.04.10 18:02:01.730 5: AMAD (Android_Tablett_Wohnzimmer) - Processing data: volume@@0@@@@
2016.04.10 18:02:02.028 5: AMAD (AMADCommBridge) - Receive RAW Message in Debugging Mode: POST / HTTP/1.1
Content-Type: text/plain
User-Agent: Mozilla/5.0 (compatible; Automagic)
FHEMDEVICE: Android_Tablett_Wohnzimmer
FHEMCMD: setreading
Host: 192.168.188.47:8090
Connection: Keep-Alive
Accept-Encoding: gzip
Content-Length: 63

screenOrientation@@landscape@@@@screenOrientationMode@@auto@@@@
2016.04.10 18:02:02.030 4: AMAD (AMADCommBridge) - AMAD_CommBridge: processing receive reading values - Device: Android_Tablett_Wohnzimmer Data: screenOrientation@@landscape@@@@screenOrientationMode@@auto@@@@
2016.04.10 18:02:02.031 5: AMAD (Android_Tablett_Wohnzimmer) - Processing data: screenOrientation@@landscape@@@@screenOrientationMode@@auto@@@@
Fhem Cubitruck  Armbian Buster with Linux 5.3.9-sunxi
HM-CC_RT-DN, HM-Sec-RHS,HM-Sec-SD, HM-Sec-SCo,IT1500,1xIT GRR-3500 Fritz!Dect200,Powerline546E,Enigma2 Modul mit 3 Vu+,Wol Modul für WinServer2016 und WinServer 2019,FB6590
Allnetl Wandtablett mit FTUI

Helmi55

#8
10 April 2016, 18:14:14
Vielleicht hilft was - ich habe das Automagic und das FlowSet am Tablet gelöscht und neu installiert
Das hat bei mir geholfen (vor allem aber das FlowSet2.0)
System1 fhem 6.1 auf RPi 4B mit 4GB, HMUSBConfig, DS9490R-1Wire, Busware USB 868, Pool-Solarsteuerung mit FHEM. System2 fhem 6.1 auf RPi 4B mit 4GB (Bullseye) mit Busware USB 868 und 433 und HMUARTLGW für Haussteuerung

https://www.flickr.com/photos/canonhelmi/

Tommy82

#9
10 April 2016, 18:22:29
Hi,
danke für den Tip,
hab jetzt mal Automagic und alle Flowsets gelöscht und dann neuinstalliert und die 2.0 Flows und einen eigenen importiert und aktiviert, mal sehen was dann passiert.

Hab aber dann gesehen das Automagic einen Fehler meldet, daher der Automagic Log mal im Anhang der nach dem neuinstallieren kommt.
Fhem Cubitruck  Armbian Buster with Linux 5.3.9-sunxi
HM-CC_RT-DN, HM-Sec-RHS,HM-Sec-SD, HM-Sec-SCo,IT1500,1xIT GRR-3500 Fritz!Dect200,Powerline546E,Enigma2 Modul mit 3 Vu+,Wol Modul für WinServer2016 und WinServer 2019,FB6590
Allnetl Wandtablett mit FTUI

Tommy82

#10
10 April 2016, 19:59:29 Letzte Bearbeitung: 10 April 2016, 20:01:21 von Tommy82
Zum Beispiel das powerLevel reading hat sich seit 18:22 nicht geändert, und steht immer noch auf 100%, also da passt irgendwas noch nicht

EDIT
Hab gerade das hier
https://forum.fhem.de/index.php/topic,52002.0.html noch gefunden, muss ich nachher mal testen, ob es vieelicht daran liegt
Fhem Cubitruck  Armbian Buster with Linux 5.3.9-sunxi
HM-CC_RT-DN, HM-Sec-RHS,HM-Sec-SD, HM-Sec-SCo,IT1500,1xIT GRR-3500 Fritz!Dect200,Powerline546E,Enigma2 Modul mit 3 Vu+,Wol Modul für WinServer2016 und WinServer 2019,FB6590
Allnetl Wandtablett mit FTUI

CoolTux

#11
10 April 2016, 20:00:48
Was zeigt den das Tablet an. Auch 100 oder viel weniger?
Du musst nicht wissen wie es geht! Du musst nur wissen wo es steht, wie es geht.
Support me to buy new test hardware for development: https://www.paypal.com/paypalme/MOldenburg
My FHEM Git: https://git.cooltux.net/FHEM/
Das TuxNet Wiki:
https://www.cooltux.net

Tommy82

#12
10 April 2016, 20:03:24
viel ist relativ :-)  Das Tablett zeigt 97 an.

Hab meinen Beitrag oben aber gerade noch aktualisiert, muss ich nachher nochmal testen
Fhem Cubitruck  Armbian Buster with Linux 5.3.9-sunxi
HM-CC_RT-DN, HM-Sec-RHS,HM-Sec-SD, HM-Sec-SCo,IT1500,1xIT GRR-3500 Fritz!Dect200,Powerline546E,Enigma2 Modul mit 3 Vu+,Wol Modul für WinServer2016 und WinServer 2019,FB6590
Allnetl Wandtablett mit FTUI

CoolTux

#13
10 April 2016, 20:16:59
Dann sollte das Reading auch 97 an zeigen.
Melde Dich dann bitte noch mal.
Du musst nicht wissen wie es geht! Du musst nur wissen wo es steht, wie es geht.
Support me to buy new test hardware for development: https://www.paypal.com/paypalme/MOldenburg
My FHEM Git: https://git.cooltux.net/FHEM/
Das TuxNet Wiki:
https://www.cooltux.net

Tommy82

#14
11 April 2016, 20:20:12
Hi,
im Moment würde ich sagen, das es bei mir das gleiche Problem war.

Sieht so aus als ob alle readings nun bei änderungen aktualisiert würden.

Danke für den Tip und die unterstützung hier.
Fhem Cubitruck  Armbian Buster with Linux 5.3.9-sunxi
HM-CC_RT-DN, HM-Sec-RHS,HM-Sec-SD, HM-Sec-SCo,IT1500,1xIT GRR-3500 Fritz!Dect200,Powerline546E,Enigma2 Modul mit 3 Vu+,Wol Modul für WinServer2016 und WinServer 2019,FB6590
Allnetl Wandtablett mit FTUI
Drucken
Nach oben Seiten1 2 Alle
Benutzer-Aktionen