SIGNALDuino Empfänger Firm- und Hardware

Begonnen von Ralf9, 02 Oktober 2016, 22:59:51

Vorheriges Thema - Nächstes Thema

jogimaster

Sorry, etwas doof formuliert.

im eagle_pcb.jpg sind 2 Pins vorgesehen, die 2 Pins vom CC1101 Modul mit der Unterseite und dem Wemos D1 verbinden sollen. Diese sind nicht durchkontaktiert für eine doppelseitige LP.
D6 zu SO zum Beispiel. Nur Wemos, CC1101, SMA Buchse und SMD LED und R auflöten sollten nicht reichen!? Oder irre ich mich?

Denke ich zu kompliziert?

Gruß
Jogimaster

gloob

#976
Zitat von: jogimaster am 26 September 2018, 19:58:47
Sorry, etwas doof formuliert.

im eagle_pcb.jpg sind 2 Pins vorgesehen, die 2 Pins vom CC1101 Modul mit der Unterseite und dem Wemos D1 verbinden sollen. Diese sind nicht durchkontaktiert für eine doppelseitige LP.
D6 zu SO zum Beispiel. Nur Wemos, CC1101, SMA Buchse und SMD LED und R auflöten sollten nicht reichen!? Oder irre ich mich?

Denke ich zu kompliziert?

Gruß
Jogimaster

Sicher, dass diese nicht durchkontaktiert sind? Von welcher Platine sprechen wir eigentlich? Was sagt denn Locotus zu seinen Platinen, hast du ihn mal gefragt?

Wenn du von folgender Platine redest, wird D4 doch überhaupt nicht verwendet: https://forum.fhem.de/index.php/topic,58396.msg646685.html#msg646685
Raspberry Pi 3 | miniCUL 433MHz | nanoCUL 868 MHz | nanoCUL 433 MHz | MySensors WLAN Gateway | LaCrosse WLAN Gateway | SignalESP 433 MHz | SignalESP 868 MHz | HM-MOD-UART WLAN Gateway | IR - 360 Grad WLAN Gateway

jogimaster

Ja, es handelt sich um die Platine von locutus. Er nimmt aber keine PM's an, bittet hier im Forum zu fragen.
Es haben ja auch viele die Platine von ihm bekommen, daher hier die Nachfrage. Zur Verdeutlichung habe ich mal ein Foto gemacht.
Es geht um die rot markierten Stellen. Da muss doch eine Verbindung zwischen den beiden Seiten hergestellt werden!? Sonst fehlen doch 2 Verbindungen zwischen CC1101 und Wemos D1.

Jogimaster

pc1246

Hallo Jogimaster
Ich habe zwei SignalESP im Einsatz, mit der Platine von Locutus! Die laufen einwandfrei. Zudem sind die doch verbunden, wenn Du Dir den Schaltplan ansiehst! Das was du eingekringelt hast ist doch eine Verbindung von der einen zur anderen Seite der Platine!
Gruss Christoph
HP T610
Onkyo_AVR;3 Enigma2; SB_Server ; SB_Player; HM-USB mit 15 HM-CC-RT-DN, 3 HM_WDS10_TH_O, 6 HM-Sec-SCo, 4 HM-Sec-MDIR-2, 1 HM-Sen-MDIR-O-2, 8 Ferion 5000 OW ; PhilipsTV; 4 harmony hub; Jeelink mit 9 PCA301; Somfy; S7-300; 3 LGW; HUE; HM-IP auf Charly

PeMue

Zitat von: pc1246 am 27 September 2018, 13:13:39
Das was du eingekringelt hast ist doch eine Verbindung von der einen zur anderen Seite der Platine!
= Durchkontaktierung

Gruß PeMue
RPi3Bv1.2 rpiaddon 1.66 6.0 1xHM-CC-RT-DN 1.4 1xHM-TC-IT-WM 1.1 2xHB-UW-Sen-THPL-O 0.15 1x-I 0.14OTAU  1xCUNO2 1.67 2xEM1000WZ 2xUniroll 1xASH2200 3xHMS100T(F) 1xRFXtrx 90 1xWT440H 3xTFA30.3150 5xFA21
RPi1Bv2 LCDCSM 1.63 5.8 2xMAX HKT 1xMAX RT V200KW1 Heizung Wasser

jogimaster

#980
@all

Vielen Dank! Ich habe mir heute ein neues Multimeter besorgt und alle Bahnen nochmal durchgemessen. Es stimmt, die rot von mir markierten Punkte sind durchkontaktiert. Die Verbindung steht. Das alte Multimeter konnte scheinbar keine Widerstände/Durchgang mehr zu messen.

Bestücke gerade die Platine.

Gruß
Jogimaster

maddinthebrain

Bezugnehmend auf https://forum.fhem.de/index.php/topic,58396.msg824906.html#msg824906
So, hatte noch mit einem Defekt zu kämpfen und auch nur wenig Zeit. Nun läuft der 868MHz Signalduino wieder. Leider ist das Ergebnis trotz Umzugs und besserer Antenne ne absolute Katastrophe. Es werden in 24h vielleicht noch 1-2 Pakete des Außenteils der Wetterstation erfolgreich empfangen. Die Wetterstation selber funktioniert weiterhin einwandfrei. Das mit dem Störsender glaube daher nicht wirklich.
Hier mal ein Auszug aus dem Log mit verbose 4.
2018.10.09 06:21:24 4: sduino2/keepalive ok, retry = 0
2018.10.09 06:21:53 4: sduino2/msg READ: MU;P0=-1962;P1=-3394;P2=-4952;P4=-760;P5=-385;P6=1908;D=626060606164656164656564656564656465656465646565646565646564606;CP=6;R=24;
2018.10.09 06:21:53 4: sduino2: Fingerprint for MU Protocol id 44 -> BresserTemeo matches, trying to demodulate
2018.10.09 06:21:53 4: sduino2: Fingerprint for MU Protocol id 44.1 -> BresserTemeo matches, trying to demodulate
2018.10.09 06:21:53 4: sduino2/msg READ: MU;P0=-3318;P1=1723;P2=-1985;P3=-366;P4=-4716;P5=-704;P6=-6452;P7=2304;D=01213121213101313141212121015131015131315131313131513131313151315131315131513121615127313151;CP=1;R=3;
2018.10.09 06:21:53 4: sduino2: Fingerprint for MU Protocol id 44 -> BresserTemeo matches, trying to demodulate
2018.10.09 06:21:53 4: sduino2: Fingerprint for MU Protocol id 44.1 -> BresserTemeo matches, trying to demodulate
2018.10.09 06:22:27 4: sduino2/keepalive ok, retry = 0
2018.10.09 06:22:42 4: sduino2/msg READ: MU;P0=-372;P1=1733;P2=-3434;P3=-667;P4=-2271;P6=-6752;P7=-5076;D=01213101013101310101310131010131013101013101310141610141013131714121313131;CP=1;R=24;
2018.10.09 06:22:42 4: sduino2: Fingerprint for MU Protocol id 44 -> BresserTemeo matches, trying to demodulate
2018.10.09 06:22:42 4: sduino2: Fingerprint for MU Protocol id 44.1 -> BresserTemeo matches, trying to demodulate
2018.10.09 06:23:30 4: sduino2/keepalive ok, retry = 0
2018.10.09 06:23:30 4: sduino2/msg READ: MU;P0=-2167;P1=1889;P2=-772;P3=-3288;P4=-384;P5=-5341;P6=4660;D=012131412151010101314631214141214141214141414121414121414141412141410151210141465101314641;CP=1;R=24;
2018.10.09 06:23:30 4: sduino2: Fingerprint for MU Protocol id 44 -> BresserTemeo matches, trying to demodulate
2018.10.09 06:23:30 4: sduino2: Fingerprint for MU Protocol id 44.1 -> BresserTemeo matches, trying to demodulate
2018.10.09 06:23:30 4: sduino2/msg READ: MU;P0=-2190;P1=1702;P3=-384;P4=-3539;P5=-4680;P6=-688;P7=-6544;D=010131010131413131510101014131614131313131313161316131613131313161313161316161017;CP=1;R=3;
2018.10.09 06:23:30 4: sduino2: Fingerprint for MU Protocol id 44 -> BresserTemeo matches, trying to demodulate
2018.10.09 06:23:30 4: sduino2: Fingerprint for MU Protocol id 44.1 -> BresserTemeo matches, trying to demodulate
2018.10.09 06:24:17 4: sduino2/msg READ: MU;P0=1884;P1=-377;P3=-734;P4=-2065;P5=-6876;P7=-4972;D=10303030303030303030303030303030405010403010307040;CP=0;R=23;
2018.10.09 06:24:17 4: sduino2: Fingerprint for MU Protocol id 44 -> BresserTemeo matches, trying to demodulate
2018.10.09 06:24:17 4: sduino2: Fingerprint for MU Protocol id 44.1 -> BresserTemeo matches, trying to demodulate
2018.10.09 06:24:33 4: sduino2/keepalive ok, retry = 0
2018.10.09 06:25:06 4: sduino2/msg READ: MU;P0=1930;P1=-1956;P4=-761;P5=-3425;P6=-5312;P7=-384;D=010104010104050404060101010507070507070704070404040404040707070407040707040707010604010704070601050704070;CP=0;R=25;
2018.10.09 06:25:06 4: sduino2: Fingerprint for MU Protocol id 44 -> BresserTemeo matches, trying to demodulate
2018.10.09 06:25:06 4: sduino2: Fingerprint for MU Protocol id 44.1 -> BresserTemeo matches, trying to demodulate
2018.10.09 06:25:36 4: sduino2/keepalive ok, retry = 0
2018.10.09 06:26:39 4: sduino2/KeepAlive not ok, retry = 1 -> get ping
2018.10.09 06:26:40 4: sduino2/msg READ: OK
2018.10.09 06:26:40 4: sduino2/HandleWriteQueue: nothing to send, stopping timer
2018.10.09 06:26:41 4: sduino2/msg READ: MU;P0=-10220;P1=1823;P2=-2025;P3=-366;P4=-3509;P5=-756;P6=-4880;D=012131212131415131612121214131514151313151313131313151315131513131;CP=1;R=24;
2018.10.09 06:26:41 4: sduino2: Fingerprint for MU Protocol id 44 -> BresserTemeo matches, trying to demodulate
2018.10.09 06:26:41 4: sduino2: Fingerprint for MU Protocol id 44.1 -> BresserTemeo matches, trying to demodulate
2018.10.09 06:27:29 4: sduino2/msg READ: MU;P0=-3657;P1=1977;P2=-759;P3=-5904;P4=-2053;P5=-368;P7=4696;D=012121314141410151510151515121512151215151575151215151215151515141315141515121;CP=1;R=24;
2018.10.09 06:27:29 4: sduino2: Fingerprint for MU Protocol id 44 -> BresserTemeo matches, trying to demodulate
2018.10.09 06:27:29 4: sduino2: Fingerprint for MU Protocol id 44.1 -> BresserTemeo matches, trying to demodulate
2018.10.09 06:27:43 4: sduino2/keepalive ok, retry = 0
2018.10.09 06:28:18 4: sduino2/msg READ: MU;P0=-6864;P1=-687;P2=1698;P3=-2126;P4=7000;P5=-3354;P6=-356;D=123234526262526262621212121212621212126212121212121212121232026232121212;CP=2;R=25;
2018.10.09 06:28:18 4: sduino2: Fingerprint for MU Protocol id 44 -> BresserTemeo matches, trying to demodulate
2018.10.09 06:28:18 4: sduino2: Fingerprint for MU Protocol id 44.1 -> BresserTemeo matches, trying to demodulate
2018.10.09 06:28:18 4: sduino2/msg READ: MU;P0=1895;P2=-2102;P3=-746;P4=-3546;P6=-390;P7=-5748;D=020302020304030607020203060406060406060603060306030606030603030606030306030606020703020306030;CP=0;R=24;
2018.10.09 06:28:18 4: sduino2: Fingerprint for MU Protocol id 44 -> BresserTemeo matches, trying to demodulate
2018.10.09 06:28:18 4: sduino2: Fingerprint for MU Protocol id 44.1 -> BresserTemeo matches, trying to demodulate
2018.10.09 06:28:46 4: sduino2/keepalive ok, retry = 0
2018.10.09 06:29:06 4: sduino2/msg READ: MU;P0=-3772;P1=-385;P2=1703;P3=-691;P4=-2037;P5=-5770;P6=-984;D=1212321212321232121232123212425232423232625232420232;CP=2;R=24;
2018.10.09 06:29:06 4: sduino2: Fingerprint for MU Protocol id 44 -> BresserTemeo matches, trying to demodulate
2018.10.09 06:29:06 4: sduino2: Fingerprint for MU Protocol id 44.1 -> BresserTemeo matches, trying to demodulate


Vielleicht kann jemand was damit anfangen.

Hier noch das aktuelle List sduino2

Internals:
   Clients    :IT:CUL_TCM97001:SD_RSL:OREGON:CUL_TX:SD_AS:Hideki:SD_WS07:SD_WS09: :SD_WS:RFXX10REC:Dooya:SOMFY:SD_UT:SD_WS_Maverick:FLAMINGO:CUL_WS:Revolt: :FS10:CUL_FHTTK:Siro:FHT:FS20:SIGNALduino_un:
   DEF        /dev/serial/by-path/platform-3f980000.usb-usb-0:1.3:1.0-port0@57600
   DMSG       P9#FF4A63FAB4000002F20D94
   DevState   initialized
   DeviceName /dev/serial/by-path/platform-3f980000.usb-usb-0:1.3:1.0-port0@57600
   FD         19
   LASTDMSG   P9#FF4A63FAB4000002F20D94
   LASTInputDev sduino2
   MSGCNT     3844
   NAME       sduino2
   NR         60
   PARTIAL   
   RAWMSG     MU;P0=-5492;P1=471;P2=-986;P3=1457;P4=-31036;D=01212121212121212321232321232123232121232323212121212121212321232123212123212323232323232323232323232323232323232323232323232123212121212323212323232323212123212123232123212341212121212121212321232321232123232121232323212121212121212321232123212123212323;CP=1;R=28;O;
   RSSI       -60
   STATE      opened
   TIME       1539032034
   TYPE       SIGNALduino
   sduino2_DMSG P9#FF6A7544083230A0108B38
   sduino2_MSGCNT 41
   sduino2_RAWMSG MU;P0=-10456;P1=483;P2=-985;P3=1465;P4=-31036;D=01212121212121212321212321232123232121212321232123212323232123232323232321232323232321212323212323232121232323232123212323232323232323212323232321232323212321212323212121232341212121212121212321212321232123232121212321232123212323232123232323232321232323;CP=1;R=27;O;
   sduino2_RSSI -60.5
   sduino2_TIME 2018-10-08 22:04:18
   sendworking 0
   unknownmessages
   version    V 3.3.1-RC7 SIGNALduino cc1101  - compiled at May 11 2018 23:00:28
   DoubleMsgIDs:
   MatchList:
     10:SD_WS07 ^P7#[A-Fa-f0-9]{6}F[A-Fa-f0-9]{2}(#R[A-F0-9][A-F0-9]){0,1}$
     11:SD_WS09 ^P9#F[A-Fa-f0-9]+
     12:SD_WS   ^W\d+x{0,1}#.*
     13:RFXX10REC ^(20|29)[A-Fa-f0-9]+
     14:Dooya   ^P16#[A-Fa-f0-9]+
     15:SOMFY   ^Ys[0-9A-F]+
     16:SD_WS_Maverick ^P47#[A-Fa-f0-9]+
     17:SD_UT   ^u30#.*
     18:FLAMINGO ^P13#[A-Fa-f0-9]+
     19:CUL_WS  ^K[A-Fa-f0-9]{5,}
     1:IT       ^i......
     20:Revolt  ^r[A-Fa-f0-9]{22}
     21:FS10    ^P61#[A-F0-9]+
     22:Siro    ^P72#[A-Fa-f0-9]+
     23:FHT     ^81..(04|09|0d)..(0909a001|83098301|c409c401)..
     24:FS20    ^81..(04|0c)..0101a001
     2:CUL_TCM97001 ^s[A-Fa-f0-9]+
     3:SD_RSL   ^P1#[A-Fa-f0-9]{8}
     4:OREGON   ^(3[8-9A-F]|[4-6][0-9A-F]|7[0-8]).*
     5:CUL_TX   ^TX..........
     6:SD_AS    ^P2#[A-Fa-f0-9]{7,8}
     7:Hideki   ^P12#75[A-F0-9]+
     9:CUL_FHTTK ^T[A-F0-9]{8}
     X:SIGNALduino_un ^[u]\d+#.*
   QUEUE:
   READINGS:
     2018-10-08 23:04:23   ccconf          freq:868.300MHz bWidth:270KHz rAmpl:42dB sens:4dB  (DataRate:350.24Baud)
     2017-10-10 19:06:07   ccpatable       C3E = 00 84 00 00 00 00 00 00  => 5_dBm
     2017-10-08 11:38:43   config          MS=1;MU=1;MC=1
     2018-10-09 11:03:17   ping            OK
     2018-10-07 01:03:25   state           opened
     2018-10-07 01:03:25   version         V 3.3.1-RC7 SIGNALduino cc1101  - compiled at May 11 2018 23:00:28
   getcmd:
   keepalive:
     ok         1
     retry      0
   mcIdList:
     10
     11
     12
     18
     43
     47
     52
     57
     58
   msIdList:
     0
     1
     13
     14
     15
     17
     2
     22
     23
     25
     3
     3.1
     32
     33
     35
     38
     4
     41
     51
     55
     6
     68
     7
     72.1
   muIdList:
     13.1
     16
     20
     21
     24
     26
     27
     28
     29
     30
     31
     36
     37
     39
     40
     44
     44.1
     45
     46
     48
     49
     5
     50
     56
     59
     60
     61
     62
     64
     65
     66
     67
     69
     70
     71
     72
     75
     8
     9
Attributes:
   DbLogExclude .*
   WS09_CRCAUS 2
   event-on-change-reading state
   flashCommand avrdude -c arduino -b [BAUDRATE] -P [PORT] -p atmega328p -vv -U flash:w:[HEXFILE] 2>[LOGFILE]
   hardware   nanoCC1101
   icon       cul_868
   room       Funk & Kommunikation
   verbose    0


Viele Grüße

Martin
Viele Grüße
Martin

Futro mit Proxmox und Debian: FHEM, Signalduino 433MHz & 868MHz, MAX!, WeeWX, FHEM2FHEM,
Raspi 4 mit ConBee mit deCONZ und Phoscon für ZigBee Aktoren und Sensoren

gloob

Zitat von: maddinthebrain am 09 Oktober 2018, 11:17:38
Bezugnehmend auf https://forum.fhem.de/index.php/topic,58396.msg824906.html#msg824906
So, hatte noch mit einem Defekt zu kämpfen und auch nur wenig Zeit. Nun läuft der 868MHz Signalduino wieder. Leider ist das Ergebnis trotz Umzugs und besserer Antenne ne absolute Katastrophe. Es werden in 24h vielleicht noch 1-2 Pakete des Außenteils der Wetterstation erfolgreich empfangen. Die Wetterstation selber funktioniert weiterhin einwandfrei. Das mit dem Störsender glaube daher nicht wirklich.

Was für ein Funkmodul nutzt du denn? Ich hatte in letzter Zeit viele Probleme mit fehlerhaften CC1101 Modulen. Vielleicht kannst du mal ein Bild davon posten.
Raspberry Pi 3 | miniCUL 433MHz | nanoCUL 868 MHz | nanoCUL 433 MHz | MySensors WLAN Gateway | LaCrosse WLAN Gateway | SignalESP 433 MHz | SignalESP 868 MHz | HM-MOD-UART WLAN Gateway | IR - 360 Grad WLAN Gateway

pejonp

Was ist es für eine Wetterstation?
Mal beim der WE verbose=5 setzen.
Wenn es eine wh1080 ist bitte ins Forum für die wh1080.
https://forum.fhem.de/index.php/topic,39451.msg720247.html#msg720247
Pejonp
LaCrossGW 868MHz:WT470+TFA+TX37-IT+EMT7110+W136+WH25A HP1003+WH2621
SignalD(CC1101):Bresser+WS-0101(868MHz WH1080)+Velux KLF200+MAX!+HM-MOD-UART:Smoke HM-SEC-SD+VITOSOLIC 200 RESOL VBUS-LAN+SolarEdge SE5K(Modbus)+Sonnen!eco8(10kWh)+TD3511+DRT710M(Modbus)+ZigBee+Z-Wave+MQTT+vitoconnect

maddinthebrain

Viele Grüße
Martin

Futro mit Proxmox und Debian: FHEM, Signalduino 433MHz & 868MHz, MAX!, WeeWX, FHEM2FHEM,
Raspi 4 mit ConBee mit deCONZ und Phoscon für ZigBee Aktoren und Sensoren

Markus.

Hallo Zusammen,

wo finde ich denn die letzte Version der SignalESP-Firmware für Wemos D1 Mini und CC1101(433) ?
Verwende eigentlich nur IT.

Gruß

Markus

andies

Kann mir jemand helfen, ich habe massenweise Fehlermeldungen der Form
2018.10.23 08:53:07 2: sduino: CUL_TCM97001 Unknown device Unknown, please define it
2018.10.23 08:55:37 2: sduino: CUL_TCM97001 Unknown device Unknown, please define it
2018.10.23 08:55:38 2: sduino: CUL_TCM97001 Unknown device Unknown, please define it
2018.10.23 09:11:27 2: sduino: CUL_TCM97001 Unknown device Unknown, please define it
2018.10.23 09:20:38 2: sduino: CUL_TCM97001 Unknown device Unknown, please define it
2018.10.23 09:25:37 2: sduino: CUL_TCM97001 Unknown device CUL_TCM97001_172, please define it

obwohl ich doch eigentlich diese Meldungen unterdrückt habe (verbose 0!!):
Internals:
   Clients    :IT:CUL_TCM97001:SD_RSL:OREGON:CUL_TX:SD_AS:Hideki:SD_WS07:SD_WS09: :SD_WS:RFXX10REC:Dooya:SOMFY:SD_UT:SD_WS_Maverick:FLAMINGO:CUL_WS:Revolt: :FS10:CUL_FHTTK:Siro:FHT:FS20:CUL_EM:SIGNALduino_un:
   DEF        /dev/serial/by-id/usb-FTDI_FT232R_USB_UART_A104WS3F-if00-port0
   DMSG       W44x#0F2DA20AF0D25DF5D4
   DevState   initialized
   DeviceName /dev/serial/by-id/usb-FTDI_FT232R_USB_UART_A104WS3F-if00-port0@57600
   FD         11
   LASTDMSG   W44x#0F2DA20AF0D25DF5D4
   MSGCNT     4285
   NAME       sduino
   NR         21
   NR_CMD_LAST_H 2
   PARTIAL   
   RAWMSG     MU;P0=200;P1=-3893;P2=3868;P3=-5864;P4=1956;P5=-1951;D=0123454545454141414145454145414145414145414545454145454545454145414541414141454545454141454145454145454145414141454141414141454145414141454145414540;CP=4;R=21;
   RSSI       -63.5
   STATE      opened
   TIME       1540305197
   TYPE       SIGNALduino
   sendworking 0
   unknownmessages
   version    V 3.3.2-rc2 SIGNALduino cc1101 - compiled at Jun  1 2018 23:56:22
   versionmodul v3.3.3-dev_20.04.
   DoubleMsgIDs:
   MatchList:
     10:SD_WS07 ^P7#[A-Fa-f0-9]{6}F[A-Fa-f0-9]{2}(#R[A-F0-9][A-F0-9]){0,1}$
     11:SD_WS09 ^P9#F[A-Fa-f0-9]+
     12:SD_WS   ^W\d+x{0,1}#.*
     13:RFXX10REC ^(20|29)[A-Fa-f0-9]+
     14:Dooya   ^P16#[A-Fa-f0-9]+
     15:SOMFY   ^Ys[0-9A-F]+
     16:SD_WS_Maverick ^P47#[A-Fa-f0-9]+
     17:SD_UT   ^u30#.*
     18:FLAMINGO ^P13#[A-Fa-f0-9]+
     19:CUL_WS  ^K[A-Fa-f0-9]{5,}
     1:IT       ^i......
     20:Revolt  ^r[A-Fa-f0-9]{22}
     21:FS10    ^P61#[A-F0-9]+
     22:Siro    ^P72#[A-Fa-f0-9]+
     23:FHT     ^81..(04|09|0d)..(0909a001|83098301|c409c401)..
     24:FS20    ^81..(04|0c)..0101a001
     25:CUL_EM  ^E0.................
     2:CUL_TCM97001 ^s[A-Fa-f0-9]+
     3:SD_RSL   ^P1#[A-Fa-f0-9]{8}
     4:OREGON   ^(3[8-9A-F]|[4-6][0-9A-F]|7[0-8]).*
     5:CUL_TX   ^TX..........
     6:SD_AS    ^P2#[A-Fa-f0-9]{7,8}
     7:Hideki   ^P12#75[A-F0-9]+
     9:CUL_FHTTK ^T[A-F0-9]{8}
     X:SIGNALduino_un ^[u]\d+#.*
   QUEUE:
   READINGS:
     2017-06-26 16:33:12   ITParms         Unsupported command
     2018-08-25 13:08:06   ccconf          freq:433.920MHz bWidth:650KHz rAmpl:42dB sens:4dB  (DataRate:5603.79Baud)
     2018-07-31 11:37:24   ccpatable       C3E = 00 C0 00 00 00 00 00 00  => 10_dBm
     2017-06-26 16:53:00   ccreg           C3E = 00 84 00 00 00 00 00 00
     2018-05-27 15:09:18   config          MS=1;MU=1;MC=1;Mred=1;Mdebug=1_MScnt=4;MuSplitThresh=8000;MdebFifoLimit=80
     2018-05-27 15:09:14   freeram         450
     2018-05-08 21:22:16   logEntry        freq:433.920MHz bWidth:325KHz rAmpl:42dB sens:4dB  (DataRate:3173.83Baud)
     2018-10-06 08:42:00   ping            OK
     2018-05-06 22:06:13   raw             C0Dn03=10B071
     2018-10-21 16:12:05   state           opened
     2018-05-27 15:09:00   uptime          0 00:07:35
     2018-10-21 16:12:05   version         V 3.3.2-rc2 SIGNALduino cc1101 - compiled at Jun  1 2018 23:56:22
   XMIT_TIME:
     1540300413
     1540300623
   getcmd:
   keepalive:
     ok         1
     retry      0
   mcIdList:
     10
     11
     12
     18
     43
     47
     52
     57
     58
   msIdList:
     0
     1
     2
     3
     3.1
     4
     6
     7
     13
     13.2
     14
     15
     17
     22
     23
     25
     32
     33
     35
     38
     51
     55
     65
     68
     72.1
   muIdList:
     5
     8
     9
     13.1
     16
     17.1
     20
     21
     24
     26
     27
     28
     29
     30
     31
     36
     39
     44
     44.1
     45
     46
     48
     49
     50
     56
     59
     60
     61
     62
     64
     66
     67
     69
     70
     71
     72
     75
     79
Attributes:
   blacklist_IDs 41,40,37
   devStateIcon Initialized:cul_usb@green:Open Open:cul_usb@red:Initialized
   flashCommand avrdude -c arduino -b 57600 -P [PORT] -p atmega328p -vv -U flash:w:[HEXFILE] 2>[LOGFILE]
   group      intern
   hardware   nanoCC1101
   verbose    0
FHEM 6.1 auf RaspPi3 (Raspbian:  6.1.21-v8+; Perl: v5.32.1)
SIGNALduino (433 MHz) und HM-UART (868 MHz), Sonoff, Blitzwolf, Somfy RTS, CAME-Gartentor, Volkszähler, Keyence-Sensor, Homematic-Sensoren und -thermostat, Ferraris-Zähler für Wasseruhr, Openlink-Nachbau Viessmann

juergs

Hallo andies,

einfach mal die FHEM-Suche ind er Einstiegsseite bemühen "CUL_TCM97001" oder "CUL_TCM97001 Unknown device Unknown, please define it".

Jürgen

andies

ja, hatte ich - da wurde auf den CUL verwiesen (ein Eintrag). Ich habe aber den SIGNALduino und, was mich verwirrt, er meldet trotz verbose 0.
FHEM 6.1 auf RaspPi3 (Raspbian:  6.1.21-v8+; Perl: v5.32.1)
SIGNALduino (433 MHz) und HM-UART (868 MHz), Sonoff, Blitzwolf, Somfy RTS, CAME-Gartentor, Volkszähler, Keyence-Sensor, Homematic-Sensoren und -thermostat, Ferraris-Zähler für Wasseruhr, Openlink-Nachbau Viessmann

Ralf9

Eine Ursache kann ein TCM97001 sensor sein der schlecht empfangen wird oder bei dem die Batterie fast leer ist.

Mit get sduino protocolIDs kannst Du sehen, daß die IDs 0, 38 und 68 das CUL_TCM97001 Modul verwenden.

Wenn Du keine Sensoren vom CUL_TCM97001 Modul hast, dann kannst Du diese IDs in die Blacklist eintragen.

Gruß Ralf
FHEM auf Cubietruck mit Igor-Image, SSD und  hmland + HM-CFG-USB-2,  HMUARTLGW Lan,   HM-LC-Bl1PBU-FM, HM-CC-RT-DN, HM-SEC-SC-2, HM-MOD-Re-8, HM-MOD-Em-8
HM-Wired:  HMW_IO_12_FM, HMW_Sen_SC_12_DR, Selbstbau IO-Module HBW_IO_SW
Maple-SIGNALduino, WH3080,  Hideki, Id 7