Autor Thema: CUL / Intertek frustration [solved]  (Gelesen 104 mal)

Offline Doddster

  • New Member
  • *
  • Beiträge: 4
CUL / Intertek frustration [solved]
« am: 19 März 2017, 10:20:09 »
Hi Guys,

I've been trying for a week now to get my CC1101-USB-Lite to talk to my Intertek radio sockets( Funksteckdosen) with no success.

I've flashed the stick and can read the config from the stick so I'm guessing it's ok (the green light is flashing),  but none of the devices react to the commands. I have SlowRF set and am addressing the devices using the hex codes as defined in the fhem wiki (Intertechno Code Berechnung), but nothing happens. If I use the remote that came with the set all devices work.

Is there a ways to switch the stick into receive mode so I can tell if it's seeing the remote commands, this might help me.

Any other ideas greatly appreciated.

Thanks,

Graham
« Letzte Änderung: 19 März 2017, 14:41:57 von Doddster »

Online KölnSolar

  • Hero Member
  • *****
  • Beiträge: 1294
Antw:CUL / Intertek frustration
« Antwort #1 am: 19 März 2017, 11:00:23 »
Hi Graham,

which version did you flash to the USB-stick ? Is FHEM up to date ? Did you find and able to understand the german Threads about Intertek ?

Best regards Markus
Edit: Do you have other devices working with the stick ?
RPi3/2 Jessie-RFXTRX-IT-RSL-NC5462-Oregon-CUL433-CUL868-FS20A4-EMGZ-1W(GPIO)-DS18B20-CO2-USBRS232-USBRS422

Offline Wichtel

  • Jr. Member
  • **
  • Beiträge: 69
Antw:CUL / Intertek frustration
« Antwort #2 am: 19 März 2017, 11:18:34 »
Do you get the right frequency setting when doing "get CUL ccconf" ?
For my setup of original Intertechno with rotating switches and cheap sockets from "Pollin" with DIP-Switches its "freq:433.920MHz bWidth:325KHz rAmpl:42dB sens:4dB".

You have autocreate enabled?

When opening event monitor and pressing the remote, nothing happens?
It should...

Offline Doddster

  • New Member
  • *
  • Beiträge: 4
Antw:CUL / Intertek frustration
« Antwort #3 am: 19 März 2017, 11:34:08 »
Hi Graham,

which version did you flash to the USB-stick ? Is FHEM up to date ? Did you find and able to understand the german Threads about Intertek ?

Best regards Markus
Edit: Do you have other devices working with the stick ?

Hi Marcus,

I used 1.66 _V3 which I believe is the correct one and yes FHEM is up to date.

I have read the german threads and understand how to setup the dip switches and which HEX codes to use. I also used the remote to verify the devices are working. I have no other devices working with the stick, I got the stick because it supports the Funksteckdosen

I am new to FHEM so I think it is more a configuration problem.

Thank you,

Graham
« Letzte Änderung: 19 März 2017, 11:51:55 von Doddster »

Offline Doddster

  • New Member
  • *
  • Beiträge: 4
Antw:CUL / Intertek frustration
« Antwort #4 am: 19 März 2017, 11:50:24 »
Do you get the right frequency setting when doing "get CUL ccconf" ?
For my setup of original Intertechno with rotating switches and cheap sockets from "Pollin" with DIP-Switches its "freq:433.920MHz bWidth:325KHz rAmpl:42dB sens:4dB".

You have autocreate enabled?

When opening event monitor and pressing the remote, nothing happens?
It should...

Hi,

yes when I do a get CUL cconf I get exactly the same as you and autocreate is enabled.

But I get nothing in the event monitor when I use the remote. Do I need to configure CUL to read the remote, or should it pick up the remote signal automatically?

Thank you,

Graham

Online KölnSolar

  • Hero Member
  • *****
  • Beiträge: 1294
Antw:CUL / Intertek frustration
« Antwort #5 am: 19 März 2017, 12:58:43 »
flash the newest version of aculfw. this should help  ;D
RPi3/2 Jessie-RFXTRX-IT-RSL-NC5462-Oregon-CUL433-CUL868-FS20A4-EMGZ-1W(GPIO)-DS18B20-CO2-USBRS232-USBRS422
Zustimmung Zustimmung x 1 Liste anzeigen

Offline Doddster

  • New Member
  • *
  • Beiträge: 4
Antw:CUL / Intertek frustration
« Antwort #6 am: 19 März 2017, 14:41:31 »
Hi Marcus,

flashed with the latest a-culfw and it works ;D

thanks for the help.

Graham

Online KölnSolar

  • Hero Member
  • *****
  • Beiträge: 1294
Antw:CUL / Intertek frustration [solved]
« Antwort #7 am: 19 März 2017, 14:53:42 »
great.
please add a [solved] to the topic.
RPi3/2 Jessie-RFXTRX-IT-RSL-NC5462-Oregon-CUL433-CUL868-FS20A4-EMGZ-1W(GPIO)-DS18B20-CO2-USBRS232-USBRS422