Autor Thema: Problem beim Update ?  (Gelesen 310 mal)

Offline buec65

  • Jr. Member
  • **
  • Beiträge: 76
Problem beim Update ?
« am: 10 September 2018, 18:56:13 »
Beim Versuch mein fhem mit einem Update zu aktualisieren ist ein Fehler aufgetreten.

Update normal durchgelaufen und beim Neustart wird mein Floorplan nicht mehr aufgebaut und es gibt eine lange Liste mit Fehlern.

Messages collected while initializing FHEM:
configfile: OWX: Define failed, unable to identify interface type 12 for bus owxFRMPHZ
OWX: Define failed, unable to identify interface type 12 for bus owxFRM150
OWX: Define failed, unable to identify interface type 12 for bus owxFRM300
OWTHERM: Warning, no 1-Wire I/O device found for Temp_Aussen.
OWTHERM: Warning, no 1-Wire I/O device found for SP150.
OWTHERM: Warning, no 1-Wire I/O device found for SP150_Backup.
OWTHERM: Warning, no 1-Wire I/O device found for SP150_VL.
OWTHERM: Warning, no 1-Wire I/O device found for SP150_ZK.
OWTHERM: Warning, no 1-Wire I/O device found for SP150_RL.
OWTHERM: Warning, no 1-Wire I/O device found for VL_Therme.
OWTHERM: Warning, no 1-Wire I/O device found for HK_VL1.
OWTHERM: Warning, no 1-Wire I/O device found for FB_VL.
OWTHERM: Warning, no 1-Wire I/O device found for FB_RL.
OWTHERM: Warning, no 1-Wire I/O device found for HK_RL.
OWTHERM: Warning, no 1-Wire I/O device found for SP300_VL.
OWTHERM: Warning, no 1-Wire I/O device found for FB_RL1.
OWTHERM: Warning, no 1-Wire I/O device found for HK_VL.
OWTHERM: Warning, no 1-Wire I/O device found for FB_VL1.
OWTHERM: Warning, no 1-Wire I/O device found for SP300_RL.
OWTHERM: Warning, no 1-Wire I/O device found for RL_Therme.
OWTHERM: Warning, no 1-Wire I/O device found for SP300.
OWTHERM: Warning, no 1-Wire I/O device found for SP300_ZK.
./log/fhem.save: Please define FB_RL first
Please define FB_RL first
Please define FB_RL first
Please define FB_RL1 first
Please define FB_RL1 first
Please define FB_RL1 first
Please define FB_VL first
Please define FB_VL first
Please define FB_VL first
Please define FB_VL1 first
Please define FB_VL1 first
Please define FB_VL1 first
Please define HK_RL first
Please define HK_RL first
Please define HK_RL first
Please define HK_RL first
Please define HK_VL first
Please define HK_VL first
Please define HK_VL first
Please define HK_VL1 first
Please define HK_VL1 first
Please define HK_VL1 first
Please define RL_Therme first
Please define RL_Therme first
Please define RL_Therme first
Please define SP150 first
Please define SP150 first
Please define SP150 first
Please define SP150_Backup first
Please define SP150_Backup first
Please define SP150_Backup first
Please define SP150_RL first
Please define SP150_RL first
Please define SP150_RL first
Please define SP150_VL first
Please define SP150_VL first
Please define SP150_VL first
Please define SP150_ZK first
Please define SP150_ZK first
Please define SP150_ZK first
Please define SP300 first
Please define SP300 first
Please define SP300 first
Please define SP300_RL first
Please define SP300_RL first
Please define SP300_RL first
Please define SP300_VL first
Please define SP300_VL first
Please define SP300_VL first
Please define SP300_ZK first
Please define SP300_ZK first
Please define SP300_ZK first
Please define Temp_Aussen first
Please define Temp_Aussen first
Please define Temp_Aussen first
Please define VL_Therme first
Please define VL_Therme first
Please define VL_Therme first
Please define VL_Therme first
Please define VL_Therme first
Please define VL_Therme first
Please define owxFRM150 first
Please define owxFRM150 first
Please define owxFRM300 first
Please define owxFRM300 first
Please define owxFRMPHZ first
Please define owxFRMPHZ first

Autosave deactivated

es sind Arduinos die mit 1-Wire DS18b20 Temperaturen erfassen bisher so definiert

defmod PHZ FRM /dev/serial/by-id/usb-FTDI_FT232R_USB_UART_AL02VH1B-if00-port0@57600
attr PHZ room Firmata
attr PHZ sampling-interval 5000

define owxFRMPHZ OWX 12
# definiert Arduino Pin 12 als 1-Wire Eingang

define Temp_Aussen OWTHERM DS18B20 FF8A0C341604
attr Temp_Aussen IODev owxFRMPHZ
attr Temp_Aussen fp_System2017 70,215,1,Temp_Aussen
attr Temp_Aussen interval 120
attr Temp_Aussen model DS18B20
attr Temp_Aussen resolution 10
attr Temp_Aussen room OWX
attr Temp_Aussen tempHigh 75
attr Temp_Aussen tempLow -30

Device:
DEF                   /dev/serial/by-id/usb-FTDI_FT232R_USB_UART_AL02VH1B-if00-port0@57600
DeviceName   /dev/serial/by-id/usb-FTDI_FT232R_USB_UART_AL02VH1B-if00-port0@57600
FD                  32
NAME             PHZ
NOTIFYDEV    global
NR                 115
FRM
analog_pins             14,15,16,17,18,19,20,21
analog_resolutions  14:10,15:10,16:10,17:10,18:10,19:10,20:10,21:10
firmware                  _1Wire.ino
firmware_version    V_2_05
input_pins              2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19
onewire_pins         2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19
output_pins           2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19
pwm_pins              3,5,6,9,10,11
pwm_resolutions   3:8,5:8,6:8,9:8,10:8,11:8
stepper_pins         2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19
stepper_resolutions  2:21,3:21,4:21,5:21,6:21,7:21,8:21,9:21,10:21,11:21,12:21,13:21,14:21,15:21,16:21,17:21,18:21,19:21


Hat jemand eine Idee wo das Problem liegt?

Offline CoolTux

  • Developer
  • Hero Member
  • ****
  • Beiträge: 15690
Antw:Problem beim Update ?
« Antwort #1 am: 10 September 2018, 18:59:41 »
Verschieben den Beitrag mal ins 1-Wire Forum. Da gab es zu Deinem Problem glaube ein paar Einträge.
Du musst nicht wissen wie es geht! Du musst nur wissen wo es steht, wie es geht.
Support me to buy new test hardware for development: https://www.paypal.me/MOldenburg
Mein GitHub: https://github.com/LeonGaultier
kein Support für cfg Editierer

Offline dirigent

  • Full Member
  • ***
  • Beiträge: 485
Antw:Problem beim Update ?
« Antwort #2 am: 10 September 2018, 22:02:05 »
define owxFRMPHZ OWX PHZ:12Es gibt schon seit geraumer Zeit eine neue Definition.

Gruß Jens
Debian auf APU2C4, HM-CFG-USB2, SIGNALduino, HM-ES-PMSw1-Pl, AB440S, AB440R, TFA 30.3121, TFA 30.3125, ITS-150, PIR-5000, configurable Firmata USB & LAN, 1-wire: DS-18B20, DS-18S20, DS-2408, DS-2413, diverse I2C-Komponenten

Offline buec65

  • Jr. Member
  • **
  • Beiträge: 76
Antw:Problem beim Update ?
« Antwort #3 am: 20 September 2018, 15:08:48 »
Läuft bei 2 Arduino's und bei 2 nicht :-(

An den 2 fehlerhaften bekomme ich die ID aber keine Temperatur

Offline dirigent

  • Full Member
  • ***
  • Beiträge: 485
Antw:Problem beim Update ?
« Antwort #4 am: Gestern um 15:11:54 »
Eventuell handelt es sich um ein reopen-Problem. https://forum.fhem.de/index.php/topic,81815.msg749243.html#msg749243
Gruß Jens
« Letzte Änderung: Gestern um 16:19:38 von dirigent »
Debian auf APU2C4, HM-CFG-USB2, SIGNALduino, HM-ES-PMSw1-Pl, AB440S, AB440R, TFA 30.3121, TFA 30.3125, ITS-150, PIR-5000, configurable Firmata USB & LAN, 1-wire: DS-18B20, DS-18S20, DS-2408, DS-2413, diverse I2C-Komponenten

 

decade-submarginal