Hallo zusammen,
ich habe eine aktuelle FHEM installation mit einer CCU3 und möchte gerne meine Fernbedienungen HmIP-RC8 auswerten, sprich eine State bekommen wenn die jeweilige Taste gedrückt wird.
Welche Attribute müssen genau gesetzt werden mit der aktuellen HMCCU ?
Habe das mit einer alten Fernbedienung mal hin bekommen, scheint aber für neue Fernbedienungen nicht mehr zu funktionieren so.
Kann mir jemand von euch helfen ?
Internals:
DEF 000B17098F60B2:1
FUUID 61216136-f11f-c1dd-84fc-b6d8bfac322e9928
IODev CCU_3
NAME HM_FB01Taste01
NR 237
STATE on
TYPE HMCCUCHN
ccuaddr 000B17098F60B2:1
ccudevstate active
ccuif HmIP-RF
ccuname HmIP-RC8 000B17098F60B2:1
ccutype HmIP-RC8
eventCount 1
readonly no
READINGS:
2021-10-31 11:24:57 0.UNREACH 0
2021-08-22 00:08:43 1.PRESS_SHORT on
2022-12-07 14:48:02 IODev CCU_3
2022-12-07 14:08:53 PRESS_SHORT on
2022-12-07 14:48:55 activity alive
2022-12-07 14:48:55 battery ok
2021-10-31 11:24:57 battery_._._UNREACH_ 0
2022-12-07 14:08:53 control 1
2022-12-07 14:48:55 devstate ok
2022-12-07 14:48:55 hmstate on
2022-12-07 14:08:53 pressed on
2022-12-07 14:48:55 rssidevice -79
2022-12-07 14:48:55 rssipeer N/A
2022-12-07 14:08:53 state on
2022-12-07 14:48:55 voltage 2.8
hmccu:
channels 1
detect 0
devspec 000B17098F59A2:1
nodefaults 1
setDefaults 0
cmdlist:
control:
chn 1
dpt PRESS_SHORT
dp:
0.CONFIG_PENDING:
VALUES:
NVAL false
ONVAL false
OSVAL false
OVAL false
SVAL false
VAL false
0.DUTY_CYCLE:
VALUES:
NVAL false
ONVAL false
OSVAL false
OVAL false
SVAL false
VAL false
0.INSTALL_TEST:
VALUES:
NVAL true
ONVAL true
OSVAL true
OVAL true
SVAL true
VAL true
0.LOW_BAT:
VALUES:
NVAL false
ONVAL false
OSVAL ok
OVAL false
SVAL ok
VAL false
0.OPERATING_VOLTAGE:
VALUES:
NVAL 2.800000
ONVAL 2.800000
OSVAL 2.8
OVAL 2.800000
SVAL 2.8
VAL 2.800000
0.OPERATING_VOLTAGE_STATUS:
VALUES:
NVAL 0
ONVAL 0
OSVAL 0
OVAL 0
SVAL 0
VAL 0
0.RSSI_DEVICE:
VALUES:
NVAL -79
ONVAL -79
OSVAL -79
OVAL 177
SVAL -79
VAL 177
0.RSSI_PEER:
VALUES:
NVAL N/A
ONVAL N/A
OSVAL N/A
OVAL 0
SVAL N/A
VAL 0
0.UNREACH:
VALUES:
NVAL false
ONVAL false
OSVAL alive
OVAL false
SVAL alive
VAL false
0.UPDATE_PENDING:
VALUES:
NVAL false
ONVAL false
OSVAL false
OVAL false
SVAL false
VAL false
roleCmds:
get:
set:
state:
chn 1
dpt PRESS_SHORT
Attributes:
IODev CCU_3
alias Fernbedienung 01 - Taste 1
ccureadingfilter ^PRESS_SHORT$
ccureadingformat datapoint
controldatapoint PRESS_SHORT
devStateIcon on:ios-set_on
event-on-update-reading .*
group Schlafzimmer
room Homematic
sortby 08
statedatapoint PRESS_SHORT
statevals on:1
stripnumber 1
substexcl control
substitute PRESS_SHORT!(1|true):on