Moin zusammen
Ich möchte gerne den Taupunkt im Keller errechnen lassen. Als Hardware steht mit dazu ein HM-IP Wandthermostat HmIP-RF zur Verfügung, der auf dem Namen WandthermostatWaschkueche hört.
Ich habe nach Anleitung mit
define Taupunkt_Waschkueche dewpoint dewpoint WandthermostatWaschkueche measured-temp humidity Taupunkt
ein Device erzeugt. Das sieht so aus:
Internals:
CFGFN
CMD_TYPE dewpoint
DEF dewpoint WandthermostatWaschkueche measured-temp humidity Taupunkt
DEV_REGEXP WandthermostatWaschkueche
FUUID 62ab51bd-f33f-3708-6134-0e535be9bf4489b8
HUM_NAME humidity
NAME Taupunkt_Waschkueche
NEW_NAME Taupunkt
NOTIFYDEV WandthermostatWaschkueche
NR 719
NTFY_ORDER 10-Taupunkt_Waschkueche
STATE active
TEMP_NAME measured-temp
TYPE dewpoint
hmccu:
Attributes:
group Raumklima
room Waschküche
Wo steht denn jetzt der Wert für den Taupunkt? Was habe nicht verstanden?
Vielen Dank im Voraus!!
Gruß,
Frank
Hallo,
das Reading "Taupunkt" sollte in deinem angegebenen Device erscheinen! Also bei dir WandthermostatWaschkueche.
Gruß
Zitat von: kabanett am 16 Juni 2022, 21:36:21
Hallo,
das Reading "Taupunkt" sollte in deinem angegebenen Device erscheinen! Also bei dir WandthermostatWaschkueche.
Gruß
Vorausgesetzt im Device WandthermostatWaschkueche gibt es measured-temp und humidity Readings.
Weiß nicht wie das bei Homematic IP ist.
Poste doch mal ein list davon...
...und bitte in Code-Tags das '#' im "Menü".
list WandthermostatWaschkueche
Gruß, Joachim
Moin
Danke dafür. Es steht in der Tat in den Readings des Device.
Hier die Liste wie gewünscht:
Internals:
DEF 000A9D89B66F82:1
FUUID 62150f7c-f33f-3708-76c7-9153a9141da06ebf
IODev HMLanIP
NAME WandthermostatWaschkueche
NR 457
STATE 18.8
TYPE HMCCUCHN
ccuaddr 000A9D89B66F82:1
ccudevstate active
ccuif HmIP-RF
ccuname HmIP-WTH-2 000A9D89B66F82:1
ccurolectrl HEATING_CLIMATECONTROL_TRANSCEIVER
ccurolestate HEATING_CLIMATECONTROL_TRANSCEIVER
ccusubtype WTH-2
ccutype HmIP-WTH-2
firmware 2.6.0
readonly no
READINGS:
2022-06-19 13:02:47 ACTIVE_PROFILE 1
2022-06-19 13:02:47 ACTUAL_TEMPERATURE 18.8
2022-06-19 13:02:47 ACTUAL_TEMPERATURE_STATUS NORMAL
2022-06-19 13:02:47 BOOST_MODE false
2022-06-19 13:02:47 BOOST_TIME 0
2022-06-19 13:02:47 FROST_PROTECTION false
2022-06-19 13:02:47 HEATING_COOLING HEATING
2022-06-19 13:02:47 HUMIDITY 67
2022-06-19 13:02:47 HUMIDITY_STATUS NORMAL
2022-06-18 21:04:01 IODev HMLanIP
2022-06-19 13:02:47 PARTY_MODE false
2022-06-18 21:04:49 PARTY_SET_POINT_TEMPERATURE 0.0
2022-06-18 21:04:49 PARTY_TIME_END
2022-06-18 21:04:49 PARTY_TIME_START
2022-06-19 13:02:47 QUICK_VETO_TIME 0
2022-06-19 13:02:47 SET_POINT_MODE manual
2022-06-19 13:02:47 SET_POINT_TEMPERATURE 16.0
2022-06-19 13:02:47 SWITCH_POINT_OCCURED false
2022-06-19 13:02:47 Taupunkt 12.5
2022-06-19 13:02:47 WINDOW_STATE closed
2022-06-19 13:02:46 activity alive
2022-06-19 13:02:46 battery ok
2022-06-19 13:02:47 control 16.0
2022-06-19 13:02:47 desired-temp 16.0
2022-06-19 13:02:47 devstate ok
2022-06-19 13:02:47 hmstate 18.8
2022-06-19 13:02:47 humidity 67
2022-06-19 13:02:47 measured-temp 18.8
2022-06-19 13:02:46 rssidevice -90
2022-06-18 21:04:49 rssipeer -85
2022-06-19 13:02:47 state 18.8
2022-06-19 13:02:46 voltage 2.8
hmccu:
channels 1
detect 1
devspec 000A9D89B66F82:1
nodefaults 1
role 1:HEATING_CLIMATECONTROL_TRANSCEIVER
setDefaults 0
cmdlist:
get
set auto:noArg holiday:noArg desired-temp off:noArg on:noArg boost:noArg manu:noArg toggle:noArg
control:
chn 1
dpt SET_POINT_TEMPERATURE
dp:
0.CONFIG_PENDING:
VALUES:
NVAL 0
ONVAL 0
OSVAL false
OVAL 0
SVAL false
VAL 0
0.DUTY_CYCLE:
VALUES:
NVAL 0
ONVAL 0
OSVAL false
OVAL 0
SVAL false
VAL 0
0.INSTALL_TEST:
VALUES:
NVAL true
ONVAL true
OSVAL true
OVAL true
SVAL true
VAL true
0.LOW_BAT:
VALUES:
NVAL 0
ONVAL 0
OSVAL ok
OVAL 0
SVAL ok
VAL 0
0.OPERATING_VOLTAGE:
VALUES:
NVAL 2.8
ONVAL 2.8
OSVAL 2.8
OVAL 2.8
SVAL 2.8
VAL 2.8
0.OPERATING_VOLTAGE_STATUS:
VALUES:
NVAL 0
ONVAL 0
OSVAL NORMAL
OVAL 0
SVAL NORMAL
VAL 0
0.RSSI_DEVICE:
VALUES:
NVAL -90
ONVAL -91
OSVAL -91
OVAL -91
SVAL -90
VAL -90
0.RSSI_PEER:
VALUES:
NVAL -85
ONVAL -85
OSVAL -85
OVAL 171
SVAL -85
VAL 171
0.UNREACH:
VALUES:
NVAL 0
ONVAL 0
OSVAL alive
OVAL 0
SVAL alive
VAL 0
0.UPDATE_PENDING:
VALUES:
NVAL false
ONVAL false
OSVAL false
OVAL false
SVAL false
VAL false
1.ACTIVE_PROFILE:
VALUES:
NVAL 1
ONVAL 1
OSVAL 1
OVAL 1
SVAL 1
VAL 1
1.ACTUAL_TEMPERATURE:
VALUES:
NVAL 18.8
ONVAL 18.7
OSVAL 18.7
OVAL 18.7
SVAL 18.8
VAL 18.8
1.ACTUAL_TEMPERATURE_STATUS:
VALUES:
NVAL 0
ONVAL 0
OSVAL NORMAL
OVAL 0
SVAL NORMAL
VAL 0
1.BOOST_MODE:
VALUES:
NVAL 0
ONVAL 0
OSVAL false
OVAL 0
SVAL false
VAL 0
1.BOOST_TIME:
VALUES:
NVAL 0
ONVAL 0
OSVAL 0
OVAL 0
SVAL 0
VAL 0
1.FROST_PROTECTION:
VALUES:
NVAL 0
ONVAL 0
OSVAL false
OVAL 0
SVAL false
VAL 0
1.HEATING_COOLING:
VALUES:
NVAL 0
ONVAL 0
OSVAL HEATING
OVAL 0
SVAL HEATING
VAL 0
1.HUMIDITY:
VALUES:
NVAL 67
ONVAL 66
OSVAL 66
OVAL 66
SVAL 67
VAL 67
1.HUMIDITY_STATUS:
VALUES:
NVAL 0
ONVAL 0
OSVAL NORMAL
OVAL 0
SVAL NORMAL
VAL 0
1.PARTY_MODE:
VALUES:
NVAL 0
ONVAL 0
OSVAL false
OVAL 0
SVAL false
VAL 0
1.PARTY_SET_POINT_TEMPERATURE:
VALUES:
NVAL 0.000000
ONVAL 0.000000
OSVAL 0.0
OVAL 0.000000
SVAL 0.0
VAL 0.000000
1.PARTY_TIME_END:
VALUES:
NVAL
ONVAL
OSVAL
OVAL
SVAL
VAL
1.PARTY_TIME_START:
VALUES:
NVAL
ONVAL
OSVAL
OVAL
SVAL
VAL
1.QUICK_VETO_TIME:
VALUES:
NVAL 0
ONVAL 0
OSVAL 0
OVAL 0
SVAL 0
VAL 0
1.SET_POINT_MODE:
VALUES:
NVAL 1
ONVAL 1
OSVAL manual
OVAL 1
SVAL manual
VAL 1
1.SET_POINT_TEMPERATURE:
VALUES:
NVAL 16.0
ONVAL 16.0
OSVAL 16.0
OVAL 16.0
SVAL 16.0
VAL 16.0
1.SWITCH_POINT_OCCURED:
VALUES:
NVAL 0
ONVAL 0
OSVAL false
OVAL 0
SVAL false
VAL 0
1.WINDOW_STATE:
VALUES:
NVAL 0
ONVAL 0
OSVAL closed
OVAL 0
SVAL closed
VAL 0
roleCmds:
get:
set:
auto:
channel 1
role HEATING_CLIMATECONTROL_TRANSCEIVER
subcount 1
syntax V:CONTROL_MODE:0
usage auto
subcmd:
000:
args 0
dpt CONTROL_MODE
fnc
max 3
min 0
parname CONTROL_MODE
partype 3
ps VALUES
scn 000
unit
boost:
channel 1
role HEATING_CLIMATECONTROL_TRANSCEIVER
subcount 1
syntax V:BOOST_MODE:1
usage boost
subcmd:
000:
args 1
dpt BOOST_MODE
fnc
max 1
min 0
parname BOOST_MODE
partype 3
ps VALUES
scn 000
unit
desired-temp:
channel 1
role HEATING_CLIMATECONTROL_TRANSCEIVER
subcount 1
syntax V:SET_POINT_TEMPERATURE:?temperature
usage desired-temp temperature
subcmd:
000:
args
dpt SET_POINT_TEMPERATURE
fnc
max 30.5
min 4.5
parname temperature
partype 2
ps VALUES
scn 000
unit �C
holiday:
channel 1
role HEATING_CLIMATECONTROL_TRANSCEIVER
subcount 1
syntax V:CONTROL_MODE:2
usage holiday
subcmd:
000:
args 2
dpt CONTROL_MODE
fnc
max 3
min 0
parname CONTROL_MODE
partype 3
ps VALUES
scn 000
unit
manu:
channel 1
role HEATING_CLIMATECONTROL_TRANSCEIVER
subcount 1
syntax V:CONTROL_MODE:1
usage manu
subcmd:
000:
args 1
dpt CONTROL_MODE
fnc
max 3
min 0
parname CONTROL_MODE
partype 3
ps VALUES
scn 000
unit
off:
channel 1
role HEATING_CLIMATECONTROL_TRANSCEIVER
subcount 2
syntax V:CONTROL_MODE:1 V:SET_POINT_TEMPERATURE:4.5
usage off
subcmd:
000:
args 1
dpt CONTROL_MODE
fnc
max 3
min 0
parname CONTROL_MODE
partype 3
ps VALUES
scn 000
unit
001:
args 4.5
dpt SET_POINT_TEMPERATURE
fnc
max 30.5
min 4.5
parname SET_POINT_TEMPERATURE
partype 3
ps VALUES
scn 001
unit �C
on:
channel 1
role HEATING_CLIMATECONTROL_TRANSCEIVER
subcount 2
syntax V:CONTROL_MODE:1 V:SET_POINT_TEMPERATURE:30.5
usage on
subcmd:
000:
args 1
dpt CONTROL_MODE
fnc
max 3
min 0
parname CONTROL_MODE
partype 3
ps VALUES
scn 000
unit
001:
args 30.5
dpt SET_POINT_TEMPERATURE
fnc
max 30.5
min 4.5
parname SET_POINT_TEMPERATURE
partype 3
ps VALUES
scn 001
unit �C
state:
chn 1
dpt ACTUAL_TEMPERATURE
Attributes:
cmdIcon auto:sani_heating_automatic manu:sani_heating_manual boost:sani_heating_boost on:general_an off:general_aus
group Heizung_Waschkueche
icon max_wandthermostat
room Waschküche
webCmd boost