Moin zusammen,
seit einem crash meines Raspis reagiert mein JeeLink nicht mehr. Beide LED's, Blau und Rot, blinken nur noch hektisch. Neu flashen hat keine Besserung gebracht :(
Im Log kommen ständig Einträge wie dieser:
2021.02.06 18:31:50 3: Jeelink_PCA: Unknown code , help me!
Bei verbose=5 sieht das dann so aus:
2021.02.06 18:31:54 5: JeeLink/RAW: <n>/ e - turn on device <n>
0x<hhhh> h - set center frequency (Example 0xA6FE == Frequency - 868.9500MHz
<n> p - poll device <n>
<n> r - list recordings
<n> q - quiet mode (1=suppress TX and bad packets)
<n> v
2021.02.06 18:31:54 5: JeeLink/RAW: <n> v/ - version and configuration report
2021.02.06 18:31:54 5: JeeLink/RAW: /
[pcaSerial.10.1]
Available commands:
..,.. s - send data packet
l - list devices
<n> a - turn activity LED on PB1 on or off
<n> c - config (0=fill, 1=load, 2=save, 3=erase)
<n> d - turn off devi
2021.02.06 18:31:54 5: JeeLink/RAW: <n> d - turn off devi/ce <n>
<n> e - turn on device <n>
0x<hhhh> h - set center frequency (Example 0xA6FE == Frequency - 868.9500MHz
<n> p - poll device <n>
<n> r - list recordings
<n> q - quiet mode (1=suppress TX and bad pack
2021.02.06 18:31:54 5: JeeLink/RAW: <n> q - quiet mode (1=suppress TX and bad pack/ets)
<n> v - version and configuration report
List vom JeeLink:
Internals:
Clients :PCA301:EC3000:RoomNode:LaCrosse:ETH200comfort:CUL_IR:HX2272:FS20:AliRF:Level:EMT7110:KeyValueProtocol
DEF /dev/serial/by-path/platform-fd500000.pcie-pci-0000:01:00.0-usb-0:1.1.1.3:1.0-port0@57600
DeviceName /dev/serial/by-path/platform-fd500000.pcie-pci-0000:01:00.0-usb-0:1.1.1.3:1.0-port0@57600
FD 128
FUUID 601eed3e-f33f-052b-9ed6-1b793ab9405d33e7
FVERSION 36_JeeLink.pm:0.147070/2017-07-13
Jeelink_PCA_MSGCNT 2256
Jeelink_PCA_TIME 2021-02-07 11:48:23
NAME Jeelink_PCA
NR 951
NR_CMD_LAST_H 15
PARTIAL 0x<hhhh> h - set center frequency (Example 0xA6FE == Frequency -
RAWMSG
STATE initialized
TYPE JeeLink
initMessages
model [pcaSerial.10.1]
Helper:
DBLOG:
state:
fhemlogDB:
TIME 1612694903.87968
VALUE UNKNOWNCODE
MatchList:
1:PCA301 ^\S+\s+24
2:EC3000 ^\S+\s+22
3:RoomNode ^\S+\s+11
4:LaCrosse ^(\S+\s+9 |OK\sWS\s)
5:AliRF ^\S+\s+5
6:EMT7110 ^OK\sEMT7110\s
7:KeyValueProtocol ^OK\sVALUES\s
READINGS:
2021-02-07 11:48:23 state initialized
XMIT_TIME:
1612691487.76907
1612691488.7817
1612691489.79419
1612691492.66391
1612691493.67625
1612691565.90879
1612691567.11715
1612691568.145
1612691569.15868
1612691570.17215
1612691570.89849
1612691571.93084
1612691573.00467
1612691574.07601
1612691575.1441
Attributes:
devStateIcon initialized:rc_GREEN disconnected:rc_RED opened:rc_YELLOW
flashCommand avrdude -p atmega328P -c arduino -P [PORT] -D -U flash:w:[HEXFILE] 2>[LOGFILE]
initCommands 868950f v
room Radios
Jemand eine Idee wie ich den wieder zum Leben erwecken kann?
Danke & Gruß
Arthur