Hauptmenü

Neueste Beiträge

#1
Homematic / Aw: Unpairing nicht mehr mögli...
Letzter Beitrag von MadMax-FHEM - 28 März 2024, 10:39:54
Naja, erst mal (wie geschrieben) die cmds_pending "weg bekommen": "Knöpfchen drücken" (wie beim Anlernen / Achtung: ab und an sind Anlernen und Reset nicht weit auseinander ;)  )

Evtl. kommt noch ein Pairing (denke aber eher nicht), wenn die restlichen Infos zurückgelesen sind (cmds_pending), aktuell sind sie nicht gepaired (und waren es verm. auch nie).
Damit geht dann auch kein unpair!

Und (erneut) nein, nur weil du die Daten in fhem siehst heißt das noch nicht, dass auch (zu Ende) gepaired ist/wurde 8)
Siehe: https://wiki.fhem.de/wiki/HomeMatic_Devices_pairen bzw. https://wiki.fhem.de/wiki/HomeMatic_Devices_pairen#Pairing_verifizieren


D.h. eigentlich sollte es dann/jetzt reichen die Devices aus fhem zu löschen und die Geräte an der CCU anzulernen.
Falls doch nicht: reset laut Bedienungsanleitung...

Alternativ: rumtun und cmds_pending weg. "Drüber pairen" (also nix löschen! und nix resetten! sondern einfach noch mal set pair und dann Anlernvorgang beim Gerät starten) und dann unpair ;)
Etwas "überflüssig", wenn du sie in fhem nicht mehr haben willst, sondern an der CCU ;)

Gruß, Joachim
#2
Homematic / Aw: [erledigt] hmusb - neuer v...
Letzter Beitrag von the ratman - 28 März 2024, 10:28:09
Zitat von: frank am 27 März 2024, 20:23:14a) zb mit der eq3 konfigurationssoftware
b) oder mit dem eq3 update tool
ich weiß. die konfigurationssoftware findet ihn nicht, wie oben 2 mal beschrieben.
ich denke, ich muss otto leider recht geben ... der stick hat wohl schon lange nicht mehr funktioniert. gut, war immer nur als backup gedacht.
und ich hab auch noch ein RPI-RF-MOD, wenn mir auch davor graust, wieder einen raspi für ernsthafte sachen zu verwenden. aber gut, ist ja wirklich nur ein backup.
wäre halt schön gewesen, wenn der stick funktioniert hätte. aber jetzt solls gut sein, bevor sinnlos gehirnschmalz verwendet wird.
#3
Homematic / Aw: Unpairing nicht mehr mögli...
Letzter Beitrag von pointde - 28 März 2024, 10:19:57
@MadMax-Fhem. Danke für die freundliche Info  ;D
Hier ein Listing:
Internals:
   CFGFN     
   DEF        52B2B7
   FUUID      660466d5-f33f-a4e0-634a-767e140198747921
   HMLAN1_MSGCNT 36
   HMLAN1_RAWMSG E52B2B7,0000,0024D46F,FF,FFC4,33A24052B2B7263D33013F
   HMLAN1_RSSI -60
   HMLAN1_TIME 2024-03-27 19:56:54
   IODev      HMLAN1
   LASTInputDev HMLAN1
   MSGCNT     36
   NAME       HM_52B2B7
   NR         249
   NTFY_ORDER 48-HM_52B2B7
   STATE      HM_52B2B7_Btn_01 Short
   TYPE       CUL_HM
   channel_01 HM_52B2B7_Btn_01
   channel_02 HM_52B2B7_Btn_02
   disableNotifyFn 1
   eventCount 49
   lastMsg    No:33 - t:40 s:52B2B7 d:263D33 013F
   protCmdDel 7
   protCmdPend 1 CMDs_pending
   protLastRcv 2024-03-27 19:56:54
   protRcv    23 last_at:2024-03-27 19:56:54
   protResnd  5 last_at:2024-03-27 19:56:18
   protResndFail 1 last_at:2024-03-27 19:54:52
   protSnd    6 last_at:2024-03-27 19:56:13
   protState  CMDs_pending
   rssi_at_HMLAN1 cnt:37 min:-64 max:-52 avg:-58.45 lst:-60
   READINGS:
     2024-03-27 19:56:13   D-firmware      1.4
     2024-03-27 19:56:13   D-serialNr      LEQ0064981
     2024-03-27 19:56:13   IODev           HMLAN1
     2024-03-27 19:56:54   battery         ok
     2024-03-27 19:42:27   cfgState        updating
     2024-03-27 19:56:18   commState       CMDs_pending
     2024-03-27 19:56:54   state           HM_52B2B7_Btn_01 Short
   cmdStack:
     ++A01119090152B2B70400
   helper:
     HM_CMDNR   51
     cSnd       1119090152B2B70400,1119090152B2B70400
     lastMsgTm  1711565814.03821
     mId        00C2
     peerFriend peerAct,peerVirt
     peerOpt    4:pushButton
     regLst     0,1,4p
     rxType     28
     supp_Pair_Rep 0
     ack:
       263D33     HM_52B2B7_Btn_01:33
     cmds:
       TmplKey    :no:1711565284.9435
       TmplTs     1711565284.9435
       cmdKey     0:1:0::HM_52B2B7:00C2:01:
       cmdLst:
         assignHmKey noArg
         clear      [({msgErrors}|msgEvents|rssi|attack|trigger|register|oldRegs|readings|all)]
         deviceRename -newName-
         fwUpdate   -filename- [-bootTime-]
         getConfig  noArg
         getDevInfo noArg
         getRegRaw  (List0|List1|List2|List3|List4|List5|List6|List7) [-peerChn-]
         peerSmart  -peerOpt-
         raw        -data- [...]
         regBulk    -list-.-peerChn- -addr1:data1- [-addr2:data2-]...
         regSet     [(prep|{exec})] -regName- -value- [-peerChn-]
         reset      noArg
         sign       [(on|{off})]
         tplDel     -tplDel-
         tplSet_0   -tplChan-
         trgEventL  -peer- -condition-
         trgEventS  -peer- -condition-
         trgPressL  [(-peer-|{all})]
         trgPressS  [(-peer-|{all})]
         unpair     noArg
       lst:
         condition  slider,0,1,255
         peer       
         peerOpt    MWSchalter11,MWSchalter12,TeamDev
         tplChan   
         tplDel     
         tplPeer   
       rtrvLst:
         cmdList    [({short}|long)]
         deviceInfo [({short}|long)]
         list       [({normal}|full)]
         param      -param-
         reg        -addr- -list- [-peerChn-]
         regList    noArg
         regTable   noArg
         regVal     -addr- -list- [-peerChn-]
         saveConfig [-filename-]
         tplInfo    noArg
     expert:
       def        0
       det        0
       raw        1
       tpl        0
     io:
       flgs       2
       newChn     +52B2B7,02,00,00
       nextSend   1711565814.12816
       rxt        2
       vccu       VCCU
       p:
         52B2B7
         00
         00
         00
       prefIO:
     mRssi:
       mNo        33
       io:
         HMLAN1:
           -56
           -56
     peerIDsH:
     prt:
       bErr       0
       sProc      2
       sleeping   0
       wuReSent   3
     q:
       qReqConf   00
       qReqStat   
     role:
       dev        1
     rssi:
       at_HMLAN1:
         avg        -58.4594594594595
         cnt        37
         lst        -60
         max        -52
         min        -64
     tmpl:
   hmccu:
Attributes:
   IOgrp      VCCU
   autoReadReg 4_reqStatus
   expert     rawReg
   firmware   1.4
   model      HM-PB-2-WM55-2
   room       01.1_Dachboden
   serialNr   LEQ0064981
   subType    pushButton
   webCmd     getConfig:clear msgEvents

... und noch eins:

Internals:
   CFGFN     
   DEF        21E415
   FUUID      660469df-f33f-a4e0-f290-e7a2022be98d23e6
   HMLAN1_MSGCNT 6
   HMLAN1_RAWMSG E21E415,0000,00226102,FF,FFC0,64840021E4150000002100304B45513035353234343480910101
   HMLAN1_RSSI -64
   HMLAN1_TIME 2024-03-27 19:54:13
   IODev      HMLAN1
   LASTInputDev HMLAN1
   MSGCNT     6
   NAME       HM_21E415
   NR         253
   NTFY_ORDER 48-HM_21E415
   STATE      Nack
   TYPE       CUL_HM
   chanNo     01
   disableNotifyFn 1
   eventCount 14
   lastMsg    No:64 - t:00 s:21E415 d:000000 2100304B45513035353234343480910101
   protCmdDel 3
   protCmdPend 3 CMDs_pending
   protLastRcv 2024-03-27 19:54:13
   protNack   1 last_at:2024-03-27 19:50:38
   protRcv    6 last_at:2024-03-27 19:54:13
   protSnd    1 last_at:2024-03-27 19:50:38
   protState  CMDs_pending
   rssi_at_HMLAN1 cnt:6 min:-72 max:-63 avg:-66.16 lst:-64
   READINGS:
     2024-03-27 19:50:38   CommandAccepted no
     2024-03-27 19:53:40   D-firmware      2.1
     2024-03-27 19:53:40   D-serialNr      KEQ0552444
     2024-03-27 19:50:38   IODev           HMLAN1
     2024-03-27 19:53:46   cfgState        updating
     2024-03-27 19:53:46   commState       CMDs_pending
     2024-03-27 19:50:38   state           Nack
   cmdStack:
     ++A00119090121E41500040000000000
     ##A00119090121E41501040000000001
     ##A00119090121E4150103
   helper:
     HM_CMDNR   100
     cSnd       ,0119090121E41500040000000000
     getCfgList all
     getCfgListNo ,4
     lastMsgTm  1711565653.44368
     mId        0030
     peerFriend peerAct,peerVirt
     peerOpt    4:threeStateSensor
     regLst     0,1,4p
     rxType     20
     supp_Pair_Rep 0
     cmds:
       TmplKey    :no:1711565284.94295
       TmplTs     1711565284.94295
       cmdKey     1:1:0::HM_21E415:0030:01:
       cmdLst:
         assignHmKey noArg
         clear      [({msgErrors}|msgEvents|rssi|attack|trigger|register|oldRegs|readings|all)]
         deviceRename -newName-
         fwUpdate   -filename- [-bootTime-]
         getConfig  noArg
         getDevInfo noArg
         getRegRaw  (List0|List1|List2|List3|List4|List5|List6|List7) [-peerChn-]
         peerBulk   -peer1,peer2,...- [({set}|unset)]
         peerChan   -btnNumber- -actChn- [({single})] [({set}|unset)] [actor|remote|both]
         peerSmart  -peerOpt-
         raw        -data- [...]
         regBulk    -list-.-peerChn- -addr1:data1- [-addr2:data2-]...
         regSet     [(prep|{exec})] -regName- -value- [-peerChn-]
         reset      noArg
         sign       [(on|{off})]
         tplDel     -tplDel-
         tplSet_0   -tplChan-
         trgEventL  -peer- -condition-
         trgEventS  -peer- -condition-
         trgPressL  [(-peer-|{all})]
         trgPressS  [(-peer-|{all})]
         unpair     noArg
       lst:
         condition  closed,open,tilted
         peer       
         peerOpt    MWSchalter11,MWSchalter12,TeamDev
         tplChan   
         tplDel     
         tplPeer   
       rtrvLst:
         cmdList    [({short}|long)]
         deviceInfo [({short}|long)]
         list       [({normal}|full)]
         param      -param-
         reg        -addr- -list- [-peerChn-]
         regList    noArg
         regTable   noArg
         regVal     -addr- -list- [-peerChn-]
         saveConfig [-filename-]
         tplInfo    noArg
     expert:
       def        0
       det        0
       raw        1
       tpl        0
     io:
       flgs       2
       newChn     +21E415,02,00,00
       nextSend   1711565653.53563
       rxt        2
       vccu       VCCU
       p:
         21E415
         00
         00
         00
       prefIO:
     mRssi:
       mNo        64
       io:
         HMLAN1:
           -60
           -60
     peerIDsH:
     prt:
       bErr       0
       sProc      2
       tryMsg:
     q:
       qReqConf   
       qReqStat   
     role:
       chn        1
       dev        1
     rssi:
       at_HMLAN1:
         avg        -66.1666666666667
         cnt        6
         lst        -64
         max        -63
         min        -72
     tmpl:
   hmccu:
Attributes:
   IOgrp      VCCU
   autoReadReg 4_reqStatus
   expert     rawReg
   firmware   2.1
   model      HM-SEC-RHS
   room       01.1_Dachboden
   serialNr   KEQ0552444
   subType    threeStateSensor
#4
DOIF / Aw: Indirekter Zeittrigger mit...
Letzter Beitrag von Damian - 28 März 2024, 10:09:56
Zitat von: xenos1984 am 28 März 2024, 08:47:44Folgende Aufgabenstellung: Ich habe ein Device, das zwei Readings liefert, start und end. Beide sind UNIX Timestamps. Dazu habe ich noch ein weiteres Reading offset, das eine Anzahl von Sekunden enthält. Dabei kann offset auch Werte von über 24 Stunden annehmen. Gibt es eine Triggerbedingung, die innerhalb des Zeitintervalls von start - offset bis end wahr ist, und außerhalb nicht, d.h. die zu diesen beiden Zeitpunkten triggert und damit z.B. ein Gerät zu Beginn einschaltet und am Ende wieder ausschaltet?

Das sollte mit einem Zeitintervall realisierbar sein:

DOIF ([([start]-[offset])-[end]] and ["Trigger"]) (set bla..)
Beim Zeitintervall gibt es immer einen internen Trigger zum Start und zum Ende, wie von dir gewünscht.

Start- bzw. end-Reading musst du allerdings am besten über ein DOIF_Reading in HH:MM wandeln.

Das Ergebnis von start-offset wird immer als Zeitpunkt in der Zukunft interpretieret.
#5
Solaranlagen / Aw: 76_SolarForecast - Informa...
Letzter Beitrag von 300P - 28 März 2024, 10:09:16
Hab erst spät am Abend das letzte Update von deinem Contrib gezogen... vielleicht dann daher.
Ich mache erst mal "nix" und warte ab was morgen früh los ist.
Gruß
300P
#6
Solaranlagen / Aw: 76_SolarForecast - Informa...
Letzter Beitrag von DS_Starter - 28 März 2024, 10:02:45
@300P,

nein, gibt keine Hänger. Bei mir gecheckt und auch keine sonstigen Abnormitäten feststellbar.

Der train Error kann! ok sein wenn es keine Instanzen für die KI gab.
Kannst du aber nachstellen:

1. ctrlDebug=aiProcess einstellen
2. get ... valDecTree aiRawData -> es sollten (jetzt) Daten vorhanden sein
3. set ... aiDecTree addRawData
4. set ... aiDecTree addInstances
5. set ... aiDecTree train

Im Log sollte dann etwa folgendes erscheinen:

2024.03.28 09:46:50.021 1: openMeteo DEBUG> AI raw add - 41 entities added to raw data pool (set verbose 4 for output more detail)
2024.03.28 09:46:50.083 1: openMeteo DEBUG> AI raw data saved into file: ./FHEM/FhemUtils/AIraw_SolarForecast_openMeteo
2024.03.28 09:46:57.580 1: openMeteo DEBUG> AI Instance add - 41 entities added for training (set verbose 4 for output more detail)
2024.03.28 09:47:20.536 1: openMeteo DEBUG> AI Training is started in main process
2024.03.28 09:47:20.581 1: openMeteo DEBUG> AI trained number of entities: 41
2024.03.28 09:47:20.582 1: openMeteo DEBUG> AI trained and saved data into file: ./FHEM/FhemUtils/AItra_SolarForecast_openMeteo
2024.03.28 09:47:20.582 1: openMeteo DEBUG> Training instances and their associated information where purged from the AI object

LG
#7
Server - Linux / Aw: Synology Container zusamme...
Letzter Beitrag von roemi - 28 März 2024, 09:59:46
Hallo,
ich habe heute ein wenig erfolglos experimentiert  :-\
Nun haben sich kurzfristig meine Prioritäten verschoben ... meine Frau hat mich erinnert das nun Ostern ist ...  :o
Und ich habe meine USV in Betrieb genommen und will diese schnellstmöglich in Fhem einbinden.
Dank der USV hoffe ich, das mein IP Problem nicht mehr ganz oben auf der Liste steht.

Ich melde mich aber zeitnahe mit neuen Fragen zum Thema

Danke Dir

Römi
#8
InterTechno / Aw: SIGNALduino UNKNOWNCODE i1...
Letzter Beitrag von Stefan6183 - 28 März 2024, 09:49:05
Hier die FHEM log Einträge mit attr sduino1 verbose 4 mit den raw Nachrichten bei erkannter Bewegung :

2024.03.28 09:44:07 4: sduino1/msg READredu: MS;P1=307;P2=-981;P3=990;P4=-298;P5=-9519;D=15121212343434343434341212343412341212121234121234;CP=1;SP=5;R=239;O;b=69;s=1;m0;
2024.03.28 09:44:07 4: sduino1: Matched MS Protocol id 3 -> itv1, bitLen=24
2024.03.28 09:44:07 4: sduino1: Decoded MS Protocol id 3 dmsg i1FCD09 length 24 RSSI = -82.5
2024.03.28 09:44:07 4: sduino1 Dispatch: i1FCD09, -82.5 dB, dispatch
2024.03.28 09:44:07 4: sduino1 IT: message "i1FCD09" (7)
2024.03.28 09:44:07 4: sduino1 IT: msgcode "0F11101F00DF" (12) bin = 000111111100110100001001
2024.03.28 09:44:07 3: sduino1 IT: Code DF not supported by IT_0F11101F00.
2024-03-28 09:44:07 SIGNALduino sduino1 UNKNOWNCODE i1FCD09
2024.03.28 09:44:07 3: sduino1: Unknown code i1FCD09, help me!
2024.03.28 09:44:07 4: sduino1/msg READredu: MS;P1=305;P2=-990;P3=988;P4=-300;P5=-9514;D=15121212343434343434341212343412341212121234121234;CP=1;SP=5;R=239;O;m1;
2024.03.28 09:44:07 4: sduino1: Matched MS Protocol id 3 -> itv1, bitLen=24
2024.03.28 09:44:07 4: sduino1: Decoded MS Protocol id 3 dmsg i1FCD09 length 24 RSSI = -82.5
2024.03.28 09:44:07 4: sduino1 Dispatch: i1FCD09, Dropped (1) due to short time and equal msg
2024.03.28 09:44:07 4: sduino1/msg READredu: MS;P1=302;P2=-991;P3=977;P4=-305;P5=-9525;D=15121212343434343434341212343412341212121234121234;CP=1;SP=5;R=239;O;m2;
2024.03.28 09:44:07 4: sduino1: Matched MS Protocol id 3 -> itv1, bitLen=24
2024.03.28 09:44:07 4: sduino1: Decoded MS Protocol id 3 dmsg i1FCD09 length 24 RSSI = -82.5
2024.03.28 09:44:07 4: sduino1 Dispatch: i1FCD09, Dropped (2) due to short time and equal msg
2024.03.28 09:44:07 4: sduino1/msg READredu: MS;P1=308;P2=-973;P3=963;P4=-326;P5=-9532;D=15121212343434343434341212343412341212121234121234;CP=1;SP=5;R=239;O;m3;
2024.03.28 09:44:07 4: sduino1: Matched MS Protocol id 3 -> itv1, bitLen=24
2024.03.28 09:44:07 4: sduino1: Decoded MS Protocol id 3 dmsg i1FCD09 length 24 RSSI = -82.5
2024.03.28 09:44:07 4: sduino1 Dispatch: i1FCD09, Dropped (3) due to short time and equal msg

Und nochmal eine erkannte Bewegung einige Minuten später:
2024.03.28 09:53:13 4: sduino1/msg READredu: MS;P0=-9945;P1=325;P2=-970;P3=978;P4=-315;D=10121212343434343434341212343412341212121234121234;CP=1;SP=0;R=231;O;b=73;s=1;m0;
2024.03.28 09:53:13 4: sduino1: Matched MS Protocol id 3 -> itv1, bitLen=24
2024.03.28 09:53:13 4: sduino1: Decoded MS Protocol id 3 dmsg i1FCD09 length 24 RSSI = -86.5
2024.03.28 09:53:13 4: sduino1 Dispatch: i1FCD09, -86.5 dB, dispatch
2024.03.28 09:53:13 4: sduino1 IT: message "i1FCD09" (7)
2024.03.28 09:53:13 4: sduino1 IT: msgcode "0F11101F00DF" (12) bin = 000111111100110100001001
2024.03.28 09:53:13 3: sduino1 IT: Code DF not supported by IT_0F11101F00.
2024-03-28 09:53:13 SIGNALduino sduino1 UNKNOWNCODE i1FCD09
2024.03.28 09:53:13 3: sduino1: Unknown code i1FCD09, help me!
2024.03.28 09:53:13 4: sduino1/msg READredu: MS;P0=-9606;P1=338;P2=-967;P3=992;P4=-289;D=10121212343434343434341212343412341212121234121234;CP=1;SP=0;R=231;O;m1;
2024.03.28 09:53:13 4: sduino1: Matched MS Protocol id 3 -> itv1, bitLen=24
2024.03.28 09:53:13 4: sduino1: Decoded MS Protocol id 3 dmsg i1FCD09 length 24 RSSI = -86.5
2024.03.28 09:53:13 4: sduino1 Dispatch: i1FCD09, Dropped (1) due to short time and equal msg
2024.03.28 09:53:13 4: sduino1/msg READredu: MS;P0=-9606;P1=365;P2=-916;P3=1009;P4=-282;D=10121212343434343434341212343412341212121234121234;CP=1;SP=0;R=231;e;m2;
2024.03.28 09:53:13 4: sduino1: Matched MS Protocol id 3 -> itv1, bitLen=24
2024.03.28 09:53:13 4: sduino1: Decoded MS Protocol id 3 dmsg i1FCD09 length 24 RSSI = -86.5
2024.03.28 09:53:13 4: sduino1 Dispatch: i1FCD09, Dropped (2) due to short time and equal msg
2024.03.28 09:53:13 4: sduino1/msg READredu: MS;P0=-9606;P1=365;P2=-916;P3=1009;P4=-282;D=10121212343434343434341212343412341212121234121234;CP=1;SP=0;R=231;e;m3;
2024.03.28 09:53:13 4: sduino1: Matched MS Protocol id 3 -> itv1, bitLen=24
2024.03.28 09:53:13 4: sduino1: Decoded MS Protocol id 3 dmsg i1FCD09 length 24 RSSI = -86.5
2024.03.28 09:53:13 4: sduino1 Dispatch: i1FCD09, Dropped (3) due to short time and equal msg
2024.03.28 09:53:13 4: sduino1/msg READredu: MU;P0=-5888;P1=324;P2=-952;P3=992;P4=-304;P5=-7912;CP=1;R=230;D=012121234343434343434121234341234121212123412123415;e;
2024.03.28 09:53:13 4: sduino1: Fingerprint for MU Protocol id 19 -> minify matches, trying to demodulate
2024.03.28 09:53:13 4: sduino1: Fingerprint for MU Protocol id 34 -> QUIGG | LIBRA | Mandolyn | Pollin ISOTRONIC matches, trying to demodulate
2024.03.28 09:53:13 4: sduino1: Fingerprint for MU Protocol id 42 -> wireless doorbell matches, trying to demodulate
2024.03.28 09:53:13 4: sduino1: Fingerprint for MU Protocol id 60 -> WS2000 matches, trying to demodulate
2024.03.28 09:53:13 4: sduino1: Fingerprint for MU Protocol id 79 -> wireless doorbell matches, trying to demodulate
2024.03.28 09:53:13 4: sduino1: Fingerprint for MU Protocol id 95 -> Techmar matches, trying to demodulate
2024.03.28 09:53:13 4: sduino1/msg READredu: MS;P1=298;P2=-967;P4=985;P5=-309;P6=-9520;D=16121212454545454545451212454512451212121245121245;CP=1;SP=6;R=231;O;b=73;s=1;m0;
2024.03.28 09:53:13 4: sduino1: Matched MS Protocol id 3 -> itv1, bitLen=24
2024.03.28 09:53:13 4: sduino1: Decoded MS Protocol id 3 dmsg i1FCD09 length 24 RSSI = -86.5
2024.03.28 09:53:13 4: sduino1 Dispatch: i1FCD09, Dropped (4) due to short time and equal msg
2024.03.28 09:53:13 4: sduino1/msg READredu: MS;P1=300;P2=-992;P4=973;P5=-326;P6=-9526;D=16121212454545454545451212454512451212121245121245;CP=1;SP=6;R=231;O;m1;
2024.03.28 09:53:13 4: sduino1: Matched MS Protocol id 3 -> itv1, bitLen=24
2024.03.28 09:53:13 4: sduino1: Decoded MS Protocol id 3 dmsg i1FCD09 length 24 RSSI = -86.5
2024.03.28 09:53:13 4: sduino1 Dispatch: i1FCD09, Dropped (5) due to short time and equal msg
2024.03.28 09:53:14 4: sduino1/msg READredu: MS;P1=308;P2=-980;P4=973;P5=-315;P6=-9527;D=16121212454545454545451212454512451212121245121245;CP=1;SP=6;R=231;O;m2;
2024.03.28 09:53:14 4: sduino1: Matched MS Protocol id 3 -> itv1, bitLen=24
2024.03.28 09:53:14 4: sduino1: Decoded MS Protocol id 3 dmsg i1FCD09 length 24 RSSI = -86.5
2024.03.28 09:53:14 4: sduino1 Dispatch: i1FCD09, Dropped (6) due to short time and equal msg
2024.03.28 09:53:14 4: sduino1/msg READredu: MS;P1=301;P2=-985;P4=959;P5=-312;P6=-9531;D=16121212454545454545451212454512451212121245121245;CP=1;SP=6;R=231;O;m3;
2024.03.28 09:53:14 4: sduino1: Matched MS Protocol id 3 -> itv1, bitLen=24
2024.03.28 09:53:14 4: sduino1: Decoded MS Protocol id 3 dmsg i1FCD09 length 24 RSSI = -86.5
2024.03.28 09:53:14 4: sduino1 Dispatch: i1FCD09, Dropped (7) due to short time and equal msg
#9
Solaranlagen / Aw: 76_SolarForecast - Informa...
Letzter Beitrag von erwin - 28 März 2024, 09:36:45
Guten Morgen,
Danke für den Fix, läuft !!! Forcast war gestern nahe perfekt, trotz komplexer Wetterbedingungen: Sonne, Wolken, Regen abwechselnd - eher April-Wetter!
mein Kommentar zu  ...liefert OpenMeteo die Global Tilted Irradiance (GTI) vs: Gloabal Irridiance:
Die GTI ist für den Solar-Ertrag die entscheidende! Die Umrechnung ist nicht trivial, weil GI (m.Meinung nach) bereits eine Berechnung aus Solarstrahlung auf eine Fläche (Erdboden) ist.
l.g. erwin
#10
DOIF / Aw: Indirekter Zeittrigger mit...
Letzter Beitrag von betateilchen - 28 März 2024, 09:25:00
Zitat von: xenos1984 am 28 März 2024, 08:47:44Beide sind UNIX Timestamps.
...
die zu diesen beiden Zeitpunkten triggert und damit z.B. ein Gerät zu Beginn einschaltet und am Ende wieder ausschaltet?

Warum legst Du nicht einfach zwei at devices an, eines zum Einschalten und eines zum Ausschalten?
Ein at kann out-of-the-box mit einem Unix Timestamp als timespec umgehen.