Hallo Forum,
Ich habe letztes Jahr info von @alpha1974 (danke nochmals) erhalten, womit ich über BM2 den Heizkreis zwischen die verschiedene Programme schalten konnte.
In meiner HW Konfiguration ist aber anstatt Heizkreis einer Mischerkreis drin.
Ich probierte mit ebusctl grab während ich mit BM2 das Mischerkreisprogramm geändert habe den ebus Verkehr mitzufolgen, leider finde ich aber kein Pattern, welches ich mit ebusctl hex erneut schicken könnte.
z.B.
ebusctl hex 355023054423000000
ebusctl hex 3550230944230000005D010010
soviel ich weiss "5D010010" ist eine wolf speziefische Code
Kann jemand von Euch ev. helfen? Was mache ich falsch? Danke im Voraus EH
ebus Traffic (während manuelles Schalten):
30fe03010e8700d90000000001000000000000 = 1
30fe5023054423000000 = 1
30fe502305844e2a0000 = 1
30fe502305b4000a0000 = 1
3003502203cc0100 = 1
3008502203cc0200 / 027c01 = 2
3008502203cc0e00 / 029701 = 1
3008502203cc1627 / 0240fe = 2
3008502203cc1727 / 02fb00 = 2
3008502203cc192f / 020080 = 1
3008502203cc2702 / 020000 = 1
3008502203cc2902 / 020000 = 1
3008502203cc2d00 / 029600 = 1
3008502203cc362a / 02c800 = 1
3008502203cc3727 / 020100 = 1
3008502203cc372a / 02c800 = 1
3008502203cc512a / 020080 = 1
3008502203cc5904 / 020080 = 2
3008502203cc6327 / 020000 = 1
3008502203cc6a27 / 020080 = 1
3008502203cc6c01 / 020000 = 11
3008502203cc7301 / 020600 = 1
3008502203cc762a / 020080 = 1
3008502203cc7c2a / 020080 = 6
3051502203cc210a / 020000 = 1
705150140702000500194014 / 09002166150080146400 = 1
705150140702001600194014 / 09002166150080146400 = 1
705150140720000500194014 / 09002166150080146400 = 1
03f10800080080800d80020005 = 2
ebusctl i
ersion: ebusd 21.2.v21.2-48-g24a6525
update check: revision v21.2 available, broadcast.csv: different version available
access: *
signal: acquired
symbol rate: 73
max symbol rate: 125
min arbitration micros: 10
max arbitration micros: 232
min symbol latency: 0
max symbol latency: 15
reconnects: 0
masters: 6
messages: 39
conditional: 0
poll: 0
update: 6
address 03: master #11
address 08: slave #11, scanned "MF=Wolf;ID= !;SW=8000;HW=0000", loaded "wolf/08.csv"
address 10: master #2
address 15: slave #2, scanned "MF=Kromschroeder;ID= ;SW=0171;HW=0150"
address 30: master #3
address 31: master #8, ebusd
address 35: slave #3, scanned "MF=Wolf;ID=;SW=0204;HW=0100", loaded "wolf/35.csv"
address 36: slave #8, ebusd
address 51: slave, scanned "MF=Kromschroeder;ID= ;SW=0171;HW=0150"
address 70: master #4
address 75: slave #4, scanned "MF=Kromschroeder;ID= ;SW=0204;HW=8080"
address f1: master #10
address f6: slave #10, scanned "MF=Kromschroeder;ID= ;SW=0171;HW=0150"