Hallo, ich betreibe seit Jahren ein SDUINO (nanocul) auf meinem RPi 3 zur Steuerung meiner Somfy Rollladen ohne Probleme. Leider musste ich letzten feststellen, dass das Device nicht mehr funktioniert und im Status disconnected bleibt.
Ein, zweimal war das Gerät nach einem Neustart (mit kurzem Trennen des RPi von der Stromversorgung) für ein paar Stunden aktiv, ging dann aber wieder auf disconnected.
Ich habe weder softwareseitig noch hardwareseitig irgendwelche Änderungen oder Updates am System durchgeführt.
Nachdem dieser Teil über Jahre weg ohne irgendwelche Probleme funktioniert hat bin ich in der SDuino Materie nicht mehr besonders gut bewandert.
Hat jemand einen Tip wo ich mit der Fehlersuche beginnen kann, das Logfile gibt nicht viel her:
2024.06.21 15:35:33 3: sduino: getAttrDevelopment, IdList ### Attribute development is in this version ignored ###
2024.06.21 15:35:33 3: sduino: IdList, attr whitelist disabled or not defined (all IDs are enabled, except blacklisted and instable IDs):
2024.06.21 15:35:33 3: sduino: IdList, MS 0 0.1 0.2 0.3 0.4 0.5 1 3 3.1 4 6 7 7.1 13 13.2 14 15 17 20 23 25 33 33.1 33.2 35 41 49 51 53 54.1 55 65 68 74.1 87 88 90 91.1 93 106 113 118.1
2024.06.21 15:35:33 3: sduino: IdList, MU 8 9 13.1 16 17.1 19 20.1 21 22 24 26 27 28 29 30 31 32 34 36 37 38 39 40 42 44 44.1 45 46 48 49.1 49.2 50 54 56 59 60 61 62 64 66 67 69 70 71 72 73 74 76 78 79 80 81 83 84 85 86 89 91 92 94 95 97 98 99 104 105 110 111 114 118 120 121 122
2024.06.21 15:35:33 3: sduino: IdList, MC 10 11 12 18 43 47 52 57 58 96 119
2024.06.21 15:35:33 3: sduino: IdList, MN 100 101 102 103 107 107.1 108 109 112 115 116 116.1 117
2024.06.21 15:35:33 3: sduino: IdList, development protocol is active (to activate dispatch to not finshed logical module, enable desired protocol via whitelistIDs) = 2 72.1 82
...und noch das List device:
Internals:
Clients :CUL_EM:CUL_FHTTK:CUL_TCM97001:CUL_TX:CUL_WS:Dooya:FHT:FLAMINGO:FS10:FS20: :Fernotron:Hideki:IT:KOPP_FC:LaCrosse:OREGON:PCA301:RFXX10REC:Revolt:SD_AS:SD_Rojaflex: :SD_BELL:SD_GT:SD_Keeloq:SD_RSL:SD_UT:SD_WS07:SD_WS09:SD_WS:SD_WS_Maverick:SOMFY: :Siro:SIGNALduino_un:
DEF /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0@57600
DMSG nothing
DevState disconnected
DeviceName /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0@57600
FUUID 5e9f00a6-f33f-1f8d-e7e7-4c08d699ecd6ca30
IDsNoDispatch 2,72.1,82
LASTDMSG nothing
LASTDMSGID nothing
NAME sduino
NR 158
PARTIAL
STATE disconnected
TIME 1718976926.40508
TYPE SIGNALduino
versionProtocols 1.48
versionmodul 3.5.4
MatchList:
10:SD_WS07 ^P7#[A-Fa-f0-9]{6}[AFaf][A-Fa-f0-9]{2,3}
11:SD_WS09 ^P9#F[A-Fa-f0-9]+
12:SD_WS ^W\d+x{0,1}#.*
13:RFXX10REC ^(20|29)[A-Fa-f0-9]+
14:Dooya ^P16#[A-Fa-f0-9]+
15:SOMFY ^Ys[0-9A-F]+
16:SD_WS_Maverick ^P47#[A-Fa-f0-9]+
17:SD_UT ^P(?:14|20|24|26|29|30|34|46|56|68|69|76|78|81|83|86|90|91|91.1|92|93|95|97|99|104|105|114|118|121)#.*
18:FLAMINGO ^P13\.?1?#[A-Fa-f0-9]+
19:CUL_WS ^K[A-Fa-f0-9]{5,}
1:IT ^i......
20:Revolt ^r[A-Fa-f0-9]{22}
21:FS10 ^P61#[A-F0-9]+
22:Siro ^P72#[A-Fa-f0-9]+
23:FHT ^81..(04|09|0d)..(0909a001|83098301|c409c401)..
24:FS20 ^81..(04|0c)..0101a001
25:CUL_EM ^E0.................
26:Fernotron ^P82#.*
27:SD_BELL ^P(?:15|32|41|42|57|79|96|98|112)#.*
28:SD_Keeloq ^P(?:87|88)#.*
29:SD_GT ^P49#[A-Fa-f0-9]+
2:CUL_TCM97001 ^s[A-Fa-f0-9]+
30:LaCrosse ^(\S+\s+9 |OK\sWS\s)
31:KOPP_FC ^kr\w{18,}
32:PCA301 ^\S+\s+24
33:SD_Rojaflex ^P109#[A-Fa-f0-9]+
3:SD_RSL ^P1#[A-Fa-f0-9]{8}
4:OREGON ^(3[8-9A-F]|[4-6][0-9A-F]|7[0-8]).*
5:CUL_TX ^TX..........
6:SD_AS ^P2#[A-Fa-f0-9]{7,8}
7:Hideki ^P12#75[A-F0-9]+
9:CUL_FHTTK ^T[A-F0-9]{8}
X:SIGNALduino_un ^[u]\d+#.*
READINGS:
2024-06-16 08:44:30 cc1101_config Freq: 433.920 MHz, Bandwidth: 325 kHz, rAmpl: 42 dB, sens: 4 dB, DataRate: 5.60 kBaud
2024-06-16 08:44:30 cc1101_config_ext Modulation: ASK/OOK
2024-06-16 08:44:31 cc1101_patable C3E = 00 84 00 00 00 00 00 00 => 5_dBm
2024-06-17 13:45:29 ping OK
2024-06-21 15:35:26 state disconnected
2020-09-11 20:19:31 version V 3.3.1-RC7 SIGNALduino cc1101 - compiled at May 11 2018 23:00:28
additionalSets:
mcIdList:
10
11
12
18
43
47
52
57
58
96
119
mnIdList:
100
101
102
103
107
107.1
108
109
112
115
116
116.1
117
msIdList:
0
0.1
0.2
0.3
0.4
0.5
1
3
3.1
4
6
7
7.1
13
13.2
14
15
17
20
23
25
33
33.1
33.2
35
41
49
51
53
54.1
55
65
68
74.1
87
88
90
91.1
93
106
113
118.1
muIdList:
8
9
13.1
16
17.1
19
20.1
21
22
24
26
27
28
29
30
31
32
34
36
37
38
39
40
42
44
44.1
45
46
48
49.1
49.2
50
54
56
59
60
61
62
64
66
67
69
70
71
72
73
74
76
78
79
80
81
83
84
85
86
89
91
92
94
95
97
98
99
104
105
110
111
114
118
120
121
122
Attributes:
cc1101_frequency 433
hardware nanoCC1101
room Somfy
updateChannelFW testing
Mir ist folgendes aufgefallen:
Irgendwie hat sich ein Hideki Temperatursenor von einem Nachbarn von mir (Vermutlich durch autocreate) in meine Konfiguration geschlichen. Dieses Device habe ich gelöscht, jedoch scheint es noch bei den Clients im sduino device auf und ich habe keine Ahnung ob das mit dem Problem zusammenhängen kann bzw. wie ich das bereinigen kann.
Vielen Dank für eure Hilfe
ähnliche Symptomatik (https://forum.fhem.de/index.php?topic=138577.0)
Zitat von: tyrolean am 21 Juni 2024, 17:07:46Hallo, ich betreibe seit Jahren ein SDUINO (nanocul) auf meinem RPi 3 zur Steuerung meiner Somfy Rollladen ohne Probleme. Leider musste ich letzten feststellen, dass das Device nicht mehr funktioniert und im Status disconnected bleibt.
Ein, zweimal war das Gerät nach einem Neustart (mit kurzem Trennen des RPi von der Stromversorgung) für ein paar Stunden aktiv, ging dann aber wieder auf disconnected.
Ich habe weder softwareseitig noch hardwareseitig irgendwelche Änderungen oder Updates am System durchgeführt.
Nachdem dieser Teil über Jahre weg ohne irgendwelche Probleme funktioniert hat bin ich in der SDuino Materie nicht mehr besonders gut bewandert.
Hat jemand einen Tip wo ich mit der Fehlersuche beginnen kann, das Logfile gibt nicht viel her:
2024.06.21 15:35:33 3: sduino: getAttrDevelopment, IdList ### Attribute development is in this version ignored ###
2024.06.21 15:35:33 3: sduino: IdList, attr whitelist disabled or not defined (all IDs are enabled, except blacklisted and instable IDs):
2024.06.21 15:35:33 3: sduino: IdList, MS 0 0.1 0.2 0.3 0.4 0.5 1 3 3.1 4 6 7 7.1 13 13.2 14 15 17 20 23 25 33 33.1 33.2 35 41 49 51 53 54.1 55 65 68 74.1 87 88 90 91.1 93 106 113 118.1
2024.06.21 15:35:33 3: sduino: IdList, MU 8 9 13.1 16 17.1 19 20.1 21 22 24 26 27 28 29 30 31 32 34 36 37 38 39 40 42 44 44.1 45 46 48 49.1 49.2 50 54 56 59 60 61 62 64 66 67 69 70 71 72 73 74 76 78 79 80 81 83 84 85 86 89 91 92 94 95 97 98 99 104 105 110 111 114 118 120 121 122
2024.06.21 15:35:33 3: sduino: IdList, MC 10 11 12 18 43 47 52 57 58 96 119
2024.06.21 15:35:33 3: sduino: IdList, MN 100 101 102 103 107 107.1 108 109 112 115 116 116.1 117
2024.06.21 15:35:33 3: sduino: IdList, development protocol is active (to activate dispatch to not finshed logical module, enable desired protocol via whitelistIDs) = 2 72.1 82
...und noch das List device:
happy wheels (https://happy-wheels.co/)
Internals:
Clients :CUL_EM:CUL_FHTTK:CUL_TCM97001:CUL_TX:CUL_WS:Dooya:FHT:FLAMINGO:FS10:FS20: :Fernotron:Hideki:IT:KOPP_FC:LaCrosse:OREGON:PCA301:RFXX10REC:Revolt:SD_AS:SD_Rojaflex: :SD_BELL:SD_GT:SD_Keeloq:SD_RSL:SD_UT:SD_WS07:SD_WS09:SD_WS:SD_WS_Maverick:SOMFY: :Siro:SIGNALduino_un:
DEF /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0@57600
DMSG nothing
DevState disconnected
DeviceName /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0@57600
FUUID 5e9f00a6-f33f-1f8d-e7e7-4c08d699ecd6ca30
IDsNoDispatch 2,72.1,82
LASTDMSG nothing
LASTDMSGID nothing
NAME sduino
NR 158
PARTIAL
STATE disconnected
TIME 1718976926.40508
TYPE SIGNALduino
versionProtocols 1.48
versionmodul 3.5.4
MatchList:
10:SD_WS07 ^P7#[A-Fa-f0-9]{6}[AFaf][A-Fa-f0-9]{2,3}
11:SD_WS09 ^P9#F[A-Fa-f0-9]+
12:SD_WS ^W\d+x{0,1}#.*
13:RFXX10REC ^(20|29)[A-Fa-f0-9]+
14:Dooya ^P16#[A-Fa-f0-9]+
15:SOMFY ^Ys[0-9A-F]+
16:SD_WS_Maverick ^P47#[A-Fa-f0-9]+
17:SD_UT ^P(?:14|20|24|26|29|30|34|46|56|68|69|76|78|81|83|86|90|91|91.1|92|93|95|97|99|104|105|114|118|121)#.*
18:FLAMINGO ^P13\.?1?#[A-Fa-f0-9]+
19:CUL_WS ^K[A-Fa-f0-9]{5,}
1:IT ^i......
20:Revolt ^r[A-Fa-f0-9]{22}
21:FS10 ^P61#[A-F0-9]+
22:Siro ^P72#[A-Fa-f0-9]+
23:FHT ^81..(04|09|0d)..(0909a001|83098301|c409c401)..
24:FS20 ^81..(04|0c)..0101a001
25:CUL_EM ^E0.................
26:Fernotron ^P82#.*
27:SD_BELL ^P(?:15|32|41|42|57|79|96|98|112)#.*
28:SD_Keeloq ^P(?:87|88)#.*
29:SD_GT ^P49#[A-Fa-f0-9]+
2:CUL_TCM97001 ^s[A-Fa-f0-9]+
30:LaCrosse ^(\S+\s+9 |OK\sWS\s)
31:KOPP_FC ^kr\w{18,}
32:PCA301 ^\S+\s+24
33:SD_Rojaflex ^P109#[A-Fa-f0-9]+
3:SD_RSL ^P1#[A-Fa-f0-9]{8}
4:OREGON ^(3[8-9A-F]|[4-6][0-9A-F]|7[0-8]).*
5:CUL_TX ^TX..........
6:SD_AS ^P2#[A-Fa-f0-9]{7,8}
7:Hideki ^P12#75[A-F0-9]+
9:CUL_FHTTK ^T[A-F0-9]{8}
X:SIGNALduino_un ^[u]\d+#.*
READINGS:
2024-06-16 08:44:30 cc1101_config Freq: 433.920 MHz, Bandwidth: 325 kHz, rAmpl: 42 dB, sens: 4 dB, DataRate: 5.60 kBaud
2024-06-16 08:44:30 cc1101_config_ext Modulation: ASK/OOK
2024-06-16 08:44:31 cc1101_patable C3E = 00 84 00 00 00 00 00 00 => 5_dBm
2024-06-17 13:45:29 ping OK
2024-06-21 15:35:26 state disconnected
2020-09-11 20:19:31 version V 3.3.1-RC7 SIGNALduino cc1101 - compiled at May 11 2018 23:00:28
additionalSets:
mcIdList:
10
11
12
18
43
47
52
57
58
96
119
mnIdList:
100
101
102
103
107
107.1
108
109
112
115
116
116.1
117
msIdList:
0
0.1
0.2
0.3
0.4
0.5
1
3
3.1
4
6
7
7.1
13
13.2
14
15
17
20
23
25
33
33.1
33.2
35
41
49
51
53
54.1
55
65
68
74.1
87
88
90
91.1
93
106
113
118.1
muIdList:
8
9
13.1
16
17.1
19
20.1
21
22
24
26
27
28
29
30
31
32
34
36
37
38
39
40
42
44
44.1
45
46
48
49.1
49.2
50
54
56
59
60
61
62
64
66
67
69
70
71
72
73
74
76
78
79
80
81
83
84
85
86
89
91
92
94
95
97
98
99
104
105
110
111
114
118
120
121
122
Attributes:
cc1101_frequency 433
hardware nanoCC1101
room Somfy
updateChannelFW testing
Mir ist folgendes aufgefallen:
Irgendwie hat sich ein Hideki Temperatursenor von einem Nachbarn von mir (Vermutlich durch autocreate) in meine Konfiguration geschlichen. Dieses Device habe ich gelöscht, jedoch scheint es noch bei den Clients im sduino device auf und ich habe keine Ahnung ob das mit dem Problem zusammenhängen kann bzw. wie ich das bereinigen kann.
Vielen Dank für eure Hilfe
I also fixed the same error when checking if the system operation of RPi3 is stable, however nanocul connection is stable again when stopping the daemon.