Hallo,
Ich kan mein FSUD nicht gut einlernen in fhem
Ich habe jetst
define EnO_switch_0088XXXX EnOcean 0088XXXX
attr EnO_switch_0088XXXX alias Stalamp
attr EnO_switch_0088XXXX group Single Lights
attr EnO_switch_0088XXXX gwCmd dimming
attr EnO_switch_0088XXXX icon light_floor_lamp
attr EnO_switch_0088XXXX manufID 00D
attr EnO_switch_0088XXXX model other
attr EnO_switch_0088XXXX room WoonKamer
attr EnO_switch_0088XXXX stateFormat dimValue
attr EnO_switch_0088XXXX subDef FF83XXXX
attr EnO_switch_0088XXXX subType manufProfile
attr EnO_switch_0088XXXX webCmd on:off:dim
Aber fhem erkannt er als ein rollo.
Command ref "For Eltako devices attributes must be set manually. Use the sensor type "PC/FVS" for Eltako devices" Aber wie mache ich das in fhem.cfg
Danke
Henri
Hallo,
Detailansicht des Gerätes - Attribut auswählen, evtl. manuell ergänzen und mit <Enter> bzw. einem Klick auf <attr> bestätigen.
Oder aber in der FHEM-BEfehlszeile
attr <Name_des_Device> model <gewünschtes_vorhandes_Model_eintragen>Grüße
Zitat von: H3nr1 am 20 Februar 2014, 23:15:36
Hallo,
Ich kan mein FSUD nicht gut einlernen in fhem
Ich habe jetst
define EnO_switch_0088XXXX EnOcean 0088XXXX
attr EnO_switch_0088XXXX alias Stalamp
attr EnO_switch_0088XXXX group Single Lights
attr EnO_switch_0088XXXX gwCmd dimming
attr EnO_switch_0088XXXX icon light_floor_lamp
attr EnO_switch_0088XXXX manufID 00D
attr EnO_switch_0088XXXX model other
attr EnO_switch_0088XXXX room WoonKamer
attr EnO_switch_0088XXXX stateFormat dimValue
attr EnO_switch_0088XXXX subDef FF83XXXX
attr EnO_switch_0088XXXX subType manufProfile
attr EnO_switch_0088XXXX webCmd on:off:dim
Aber fhem erkannt er als ein rollo.
Command ref "For Eltako devices attributes must be set manually. Use the sensor type "PC/FVS" for Eltako devices" Aber wie mache ich das in fhem.cfg
Gerät nach Anleitung http://www.eltako.com/fileadmin/downloads/de/_bedienung/FSUD-230V_30100002-1_dt.pdf anlernen. Anlernen mit PC und GFVS am Dimmer aktivieren und dann bei Fhem teach senden.
This is how i learned my fsud-230
Lern the fsud with a enocean switch according to the manual. Turn on confirmation telegrams. turn on the light with the enocean switch. Now fhem learns the new device or watch the event monitor.
define EnO_switch_0088XXXX EnOcean 0088XXXX
attr EnO_switch_0088XXXX alias Stalamp
attr EnO_switch_0088XXXX group Single Lights
attr EnO_switch_0088XXXX gwCmd dimming
attr EnO_switch_0088XXXX icon light_floor_lamp
attr EnO_switch_0088XXXX manufID 00D
attr EnO_switch_0088XXXX model PC/FVS
attr EnO_switch_0088XXXX room WoonKamer
attr EnO_switch_0088XXXX subDef FF83XXXX
attr EnO_switch_0088XXXX subType gateway
attr EnO_switch_0088XXXX webCmd on:off:dim
Set model id manualy infhem.cfg or in the command box "attr EnO_switch_0088XXXX model PC/FVS"
Now learn the fsud. LRN/clr 0,5 sec and release and then on/off briefly once. Then in fhem "attr EnO_switch_008880BC teach"
It should work now ;D
Zitat von: H3nr1 am 26 Februar 2014, 20:50:32
This is how i learned my fsud-230
Lern the fsud with a enocean switch according to the manual. Turn on confirmation telegrams. turn on the light with the enocean switch. Now fhem learns the new device or watch the event monitor.
define EnO_switch_0088XXXX EnOcean 0088XXXX
attr EnO_switch_0088XXXX alias Stalamp
attr EnO_switch_0088XXXX group Single Lights
attr EnO_switch_0088XXXX gwCmd dimming
attr EnO_switch_0088XXXX icon light_floor_lamp
attr EnO_switch_0088XXXX manufID 00D
attr EnO_switch_0088XXXX model PC/FVS
attr EnO_switch_0088XXXX room WoonKamer
attr EnO_switch_0088XXXX subDef FF83XXXX
attr EnO_switch_0088XXXX subType gateway
attr EnO_switch_0088XXXX webCmd on:off:dim
Set model id manualy infhem.cfg or in the command box "attr EnO_switch_0088XXXX model PC/FVS"
Now learn the fsud. LRN/clr 0,5 sec and release and then on/off briefly once. Then in fhem "attr EnO_switch_008880BC teach"
It should work now ;D
"attr EnO_switch_0088XXXX model PC/FVS" is not needed.