Hallo Zusammen,
ich bin auf Igors Image umgezogen um das onboard Bluetooth für meine Anwesehnheitserkennung zu nutzen.
Leider bin ich nicht erfolgreich...
Wie mache ich den internen Bluetooth Adapter dem hcitool bekannt?
root@cubie:/etc/init.d# hcitool dev
Devices:
root@cubie:/etc/init.d# hcitool scan
Device is not available: No such device
root@cubie:/etc/init.d# uname -a
Linux cubie 3.4.104-sunxi #1 SMP PREEMPT Fri Sep 26 18:30:39 CEST 2014 armv7l GNU/Linux
Wenn schon hcitool dev keine Ausgabe liefert, brauchst Du hcitool scan gar nicht probieren ;)
Eigentlich sieht die Ausgabe so aus:
root@cubie-dev:/home/udo> hcitool dev
Devices:
hci0 43:29:B1:55:01:01
root@cubie-dev:/home/udo> hcitool scan
Scanning ...
70:56:81:AD:8E:8A MBA
root@cubie-dev:/home/udo> hciconfig
hci0: Type: BR/EDR Bus: UART
BD Address: 43:29:B1:55:01:01 ACL MTU: 1021:8 SCO MTU: 64:1
UP RUNNING PSCAN
RX bytes:1154 acl:0 sco:0 events:38 errors:0
TX bytes:927 acl:0 sco:0 commands:36 errors:0
Welche Version des Igor Images hast Du denn installiert? Bei mir funktioniert das auf zwei Cubietrucks problemlos.
Hast Du mal dmesg angeschaut, ob beim Systemstart irgendwas in Bezug auf bluetooth schiefgeht?
Ich habe mal uname -a, hcitoolconfig und dmesg abgesetzt...
root@cubie:/# uname -a
Linux cubie 3.4.104-sunxi #1 SMP PREEMPT Fri Sep 26 18:30:39 CEST 2014 armv7l GNU/Linux
root@cubie:/# hciconfig
root@cubie:/# dmesg
[ 0.000000] Booting Linux on physical CPU 0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.4.104-sunxi (root@cubie) (gcc version 4.8.2 (Ubuntu/Linaro 4.8.2-16ubuntu4) ) #1 SMP PREEMPT Fri Sep 26 18:30:39 CEST 2014
[ 0.000000] CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: sun7i
[ 0.000000] Memory Reserved:
[ 0.000000] SYS : 0x43000000 - 0x4300ffff ( 64 kB)
[ 0.000000] LCD : 0x44000000 - 0x44ffffff ( 16 MB)
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] sunxi: Allwinner A20 (AW1651/sun7i) detected.
[ 0.000000] On node 0 totalpages: 524288
[ 0.000000] free_area_init_node: node 0, pgdat c099b9c0, node_mem_map d0000000
[ 0.000000] DMA zone: 512 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 65024 pages, LIFO batch:15
[ 0.000000] Normal zone: 1008 pages used for memmap
[ 0.000000] Normal zone: 128016 pages, LIFO batch:31
[ 0.000000] HighMem zone: 2576 pages used for memmap
[ 0.000000] HighMem zone: 327152 pages, LIFO batch:31
[ 0.000000] PERCPU: Embedded 7 pages/cpu @d100e000 s8064 r8192 d12416 u32768
[ 0.000000] pcpu-alloc: s8064 r8192 d12416 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 520192
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootwait loglevel=8 rootfstype=ext4 sunxi_ve_mem_reserve=0 sunxi_g2d_mem_reserve=0 sunxi_no_mali_mem_reserve sunxi_fb_mem_reserve=16 hdmi.audio=EDID:0 disp.screen0_output_mode=EDID:1280x720p60 panic=10 consoleblank=0
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] allocated 4194304 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Memory: 2048MB = 2048MB total
[ 0.000000] Memory: 2047560k/2047560k available, 49592k reserved, 1318912K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc08f5a48 (9143 kB)
[ 0.000000] .init : 0xc08f6000 - 0xc092cf80 ( 220 kB)
[ 0.000000] .data : 0xc092e000 - 0xc09a3728 ( 470 kB)
[ 0.000000] .bss : 0xc09a374c - 0xc0b78138 (1875 kB)
[ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] Additional per-CPU info printed with stalls.
[ 0.000000] NR_IRQS:192
[ 0.000000] Architected local timer running at 24.00MHz.
[ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[ 0.000000] start_kernel(): bug: interrupts were enabled early
[ 0.000000] Console: colour dummy device 80x30
[ 0.010911] Calibrating delay loop... 1819.40 BogoMIPS (lpj=3031040)
[ 0.032646] pid_max: default: 32768 minimum: 301
[ 0.036349] Mount-cache hash table entries: 512
[ 0.040622] Initializing cgroup subsys cpuacct
[ 0.043977] Initializing cgroup subsys memory
[ 0.047418] Initializing cgroup subsys devices
[ 0.050830] Initializing cgroup subsys freezer
[ 0.054065] Initializing cgroup subsys blkio
[ 0.057752] Initializing cgroup subsys perf_event
[ 0.061330] CPU: Testing write buffer coherency: ok
[ 0.066544] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.073648] hw perfevents: enabled with ARMv7 Cortex-A7 PMU driver, 5 counters available
[ 0.079203] Setting up static identity map for 0x406564d0 - 0x40656528
[ 0.109895] CPU1: Booted secondary processor
[ 0.130856] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.132868] Brought up 2 CPUs
[ 0.138207] SMP: Total of 2 processors activated (3397.92 BogoMIPS).
[ 0.141380] devtmpfs: initialized
[ 0.147277] dummy:
[ 0.151002] NET: Registered protocol family 16
[ 0.157326] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.165099] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.169922] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.173090] [ccu-inf] aw clock manager init
[ 0.175374] [ccu-inf] aw_ccu_init
[ 0.179487] [ccu-inf] script config pll3 to 297MHz
[ 0.183254] [ccu-inf] script config pll4 to 300MHz
[ 0.187016] [ccu-inf] script config pll6 to 600MHz
[ 0.190775] [ccu-inf] script config pll7 to 297MHz
[ 0.194532] [ccu-inf] script config pll8 to 336MHz
[ 0.197287] Init eGon pin module V2.0
[ 0.206772] bio: create slab <bio-0> at 0
[ 0.210336] sunxi_gpio driver init ver 1.3
[ 0.215977] gpiochip_add: registered GPIOs 1 to 2 on device: A1X_GPIO
[ 0.219141] SCSI subsystem initialized
[ 0.222021] libata version 3.00 loaded.
[ 0.226689] usbcore: registered new interface driver usbfs
[ 0.231041] usbcore: registered new interface driver hub
[ 0.235214] usbcore: registered new device driver usb
[ 0.238337] Linux media interface: v0.10
[ 0.241963] Linux video capture interface: v2.00
[ 0.247557] Advanced Linux Sound Architecture Driver Version 1.0.25.
[ 0.253767] cfg80211: Calling CRDA to update world regulatory domain
[ 0.258426] Switching to clocksource arch_sys_counter
[ 0.260559] FS-Cache: Loaded
[ 0.262761] CacheFiles: Loaded
[ 0.274429] [usb_manager]: CONFIG_USB_SW_SUNXI_USB0_OTG
[ 0.278251] [sw_hcd0]: usb host driver initialize........
[ 0.282456] [sw_hcd0]: open_usb_clock
[ 0.304044] [sw_hcd0]: host_init_state = 1
[ 0.305015] [sw_hcd0]: platform is usb host
[ 0.307934] [sw_hcd0]: sw_hcd_host0: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx (X), HB-ISO Tx (X), SoftConn)
[ 0.319127] [sw_hcd0]: sw_hcd_init_controller: sw_hcd_host0: USB Host mode controller at f1c13000 using PIO, IRQ 70
[ 0.331667] sw_hcd_host0 sw_hcd_host0: sw_hcd host driver
[ 0.338380] sw_hcd_host0 sw_hcd_host0: new USB bus registered, assigned bus number 1
[ 0.341824] hub 1-0:1.0: USB hub found
[ 0.344758] hub 1-0:1.0: 1 port detected
[ 0.348633] wrn: hcd is not enable, need not start hcd
[ 0.350014] [sw_hcd0]: sw_usb_host0_disable start
[ 0.356052] -------sw_hcd0_soft_disconnect---------
[ 0.359036] is_on = 0, hcd0_set_vbus_cnt = 0
[ 0.362086] [sw_hcd_host0]: Set USB Power Off
[ 0.365831] wrn: hcd is not enable, need not stop hcd
[ 0.366868] [sw_hcd0]: close_usb_clock
[ 0.369343] [sw_hcd0]: sw_usb_host0_disable end
[ 0.372537] [sw_udc]: udc_init: version 20080411
[ 0.378900] NET: Registered protocol family 2
[ 0.395515] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.402487] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.410064] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[ 0.416763] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.418961] TCP: reno registered
[ 0.423849] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.429198] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.432854] NET: Registered protocol family 1
[ 0.438216] RPC: Registered named UNIX socket transport module.
[ 0.441914] RPC: Registered udp transport module.
[ 0.445585] RPC: Registered tcp transport module.
[ 0.450987] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.456724] audit: initializing netlink socket (disabled)
[ 0.460480] type=2000 audit(0.430:1): initialized
[ 0.464982] highmem bounce pool size: 64 pages
[ 0.476920] VFS: Disk quotas dquot_6.5.2
[ 0.482476] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.490268] NFS: Registering the id_resolver key type
[ 0.494911] NTFS driver 2.1.30 [Flags: R/W].
[ 0.498253] fuse init (API version 7.18)
[ 0.506594] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
[ 0.510868] msgmni has been set to 1423
[ 0.518877] alg: No test for stdrng (krng)
[ 0.525625] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.528554] io scheduler noop registered
[ 0.531797] io scheduler deadline registered
[ 0.535502] io scheduler cfq registered (default)
[ 0.540435] sunxi disp driver loaded (/dev/disp api 1.0)
[ 0.546066] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
[ 0.550736] [uart]: used uart info.: 0x05
[ 0.555440] [uart]: serial probe 0 irq 33 mapbase 0x01c28000
[ 0.579239] sunxi-uart.0: ttyS0 at MMIO 0x1c28000 (irq = 33) is a U6_16550A
[ 1.405232] console [ttyS0] enabled
[ 1.413630] [uart]: serial probe 2 irq 35 mapbase 0x01c28800
[ 1.442847] sunxi-uart.2: ttyS1 at MMIO 0x1c28800 (irq = 35) is a U6_16550A
[ 1.452403] G2D: drv_g2d_init
[ 1.458744] G2D: Module initialized.major:250
[ 1.466142] brd: module loaded
[ 1.475262] loop: module loaded
[ 1.481788] [NAND] nand driver version: 0x2 0x9
[ 1.544346] Dev Sunxi softw311 nand magic does not match for MBR 1: softw411
[ 1.557430] Dev Sunxi softw311 nand magic does not match for MBR 2:
[ 1.570479] Dev Sunxi softw311 nand magic does not match for MBR 3:
[ 1.583524] Dev Sunxi softw311 nand magic does not match for MBR 4:
[ 1.598300] Dev Sunxi softw311 nand header bad for all MBR copies, MBR corrupted or not present.
[ 1.616511] Dev Sunxi softw411 nand: part 1, start 32768, size 32768
[ 1.628449] Dev Sunxi softw411 nand: part 2, start 65536, size 14974976
[ 1.637074] nand: nand1 nand2
[ 1.643125] [NAND]nand driver, ok.
[ 1.652734] pwm-sunxi: pwm0 configured - period: 20, duty_percent: 50, duty: 10
[ 1.666417] sw_ahci sw_ahci.0: controller can't do PMP, turning off CAP_PMP
[ 1.677665] sw_ahci sw_ahci.0: forcing PORTS_IMPL to 0x1
[ 1.690414] sw_ahci sw_ahci.0: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[ 1.705290] sw_ahci sw_ahci.0: flags: ncq sntf pm led clo only pio slum part ccc
[ 1.716163] scsi0 : sw_ahci_platform
[ 1.726970] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88
[ 1.741209] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[ 1.754815] emac_init fetch emac using configuration failed
[ 1.762869] emac driver is disabled
[ 1.769918] gmac: use mac address from chipid
[ 1.778386] gmac: device MAC address 02:82:08:c0:db:82
[ 1.789183] [gmac]: sun6i_gmac platform driver registration completed
[ 1.798904] PPP generic driver version 2.4.2
[ 1.807093] PPP BSD Compression module registered
[ 1.815829] PPP Deflate Compression module registered
[ 1.825865] PPP MPPE Compression module registered
[ 1.834097] NET: Registered protocol family 24
[ 1.844591] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.856362] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.865012] [sw-ehci1]: open clock
[ 1.888438] [sw-ehci1]: Set USB Power ON
[ 1.898801] sw-ehci sw-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.912517] sw-ehci sw-ehci.1: new USB bus registered, assigned bus number 2
[ 1.923956] sw-ehci sw-ehci.1: irq 71, io mem 0x01c14000
[ 1.942043] sw-ehci sw-ehci.1: USB 2.0 started, EHCI 1.00
[ 1.950900] hub 2-0:1.0: USB hub found
[ 1.957559] hub 2-0:1.0: 1 port detected
[ 1.964164] [sw-ohci1]: open clock
[ 1.991050] sw-ohci sw-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver
[ 2.004434] sw-ohci sw-ohci.1: new USB bus registered, assigned bus number 3
[ 2.015800] sw-ohci sw-ohci.1: irq 96, io mem 0x01c14400
[ 2.081116] hub 3-0:1.0: USB hub found
[ 2.087775] hub 3-0:1.0: 1 port detected
[ 2.094308] [sw-ehci2]: open clock
[ 2.117725] [sw-ehci2]: Set USB Power ON
[ 2.128087] sw-ehci sw-ehci.2: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.141787] sw-ehci sw-ehci.2: new USB bus registered, assigned bus number 4
[ 2.153950] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 2.164509] sw-ehci sw-ehci.2: irq 72, io mem 0x01c1c000
[ 2.182043] sw-ehci sw-ehci.2: USB 2.0 started, EHCI 1.00
[ 2.190815] hub 4-0:1.0: USB hub found
[ 2.197546] hub 4-0:1.0: 1 port detected
[ 2.204111] [sw-ohci2]: open clock
[ 2.231006] sw-ohci sw-ohci.2: SW USB2.0 'Open' Host Controller (OHCI) Driver
[ 2.244358] sw-ohci sw-ohci.2: new USB bus registered, assigned bus number 5
[ 2.255719] sw-ohci sw-ohci.2: irq 97, io mem 0x01c1c400
[ 2.321165] hub 5-0:1.0: USB hub found
[ 2.327837] hub 5-0:1.0: 1 port detected
[ 2.335982] Initializing USB Mass Storage driver...
[ 2.346024] usbcore: registered new interface driver usb-storage
[ 2.355608] USB Mass Storage support registered.
[ 2.365173] usbcore: registered new interface driver ums-alauda
[ 2.376103] usbcore: registered new interface driver ums-cypress
[ 2.387147] usbcore: registered new interface driver ums-datafab
[ 2.398337] usbcore: registered new interface driver ums_eneub6250
[ 2.409522] usbcore: registered new interface driver ums-freecom
[ 2.420449] usbcore: registered new interface driver ums-isd200
[ 2.431458] usbcore: registered new interface driver ums-jumpshot
[ 2.442452] usbcore: registered new interface driver ums-karma
[ 2.453375] usbcore: registered new interface driver ums-onetouch
[ 2.464507] usbcore: registered new interface driver ums-realtek
[ 2.475433] usbcore: registered new interface driver ums-sddr09
[ 2.486265] usbcore: registered new interface driver ums-sddr55
[ 2.497010] usbcore: registered new interface driver ums-usbat
[ 2.507585] mousedev: PS/2 mouse device common for all mice
[ 2.518743] ===========================hv_keypad_init=====================
[ 2.529021] ========HV Inital ===================
[ 2.537649] tkey_fetch_sysconfig_para: tkey_unused.
[ 2.549825] hv_keypad_init: after fetch_sysconfig_para: normal_i2c: 0x0. normal_i2c[1]: 0x0
[ 2.564031] sunxi-rtc sunxi-rtc: rtc core: registered rtc as rtc0
[ 2.572640] i2c /dev entries driver
[ 2.579811] config i2c gpio with gpio_config api
[ 2.590183] axp_mfd 0-0034: AXP (CHIP ID: 0x41) detected
[ 2.601305] axp_mfd 0-0034: AXP internal temperature monitoring enabled
[ 2.613260] [AXP]axp driver uning configuration failed(342)
[ 2.620782] [AXP]power_start = 0
[ 2.627687] i2c i2c-0: Invalid probe address 0x00
[ 2.635448] I2C: i2c-0: AW16XX I2C adapter
[ 2.643588] [cedar dev]: not installed! ve_mem_reserve=0
[ 2.652301] [tt]----- avs_dev driver load... ----
[ 2.660578] [tt]----- register iomem ----
[ 2.668248] Cannot reserve region for ccmu
[ 2.676044] [tt]--- avs_dev driver load ok!! -----
[ 2.682597] [ace_drv] start!!!
[ 2.688065] [ace_drv] init end!!!
[ 2.693062] [pa_drv] start!!!
[ 2.698337] [pa_drv] init end!!!
[ 2.703951] axp20_ldo1: 1300 mV
[ 2.712367] axp20_ldo2: 1800 <--> 3300 mV at 3000 mV
[ 2.722473] axp20_ldo3: 700 <--> 3500 mV at 2800 mV
[ 2.732529] axp20_ldo4: 1250 <--> 3300 mV at 2800 mV
[ 2.742694] axp20_buck2: 700 <--> 2275 mV at 1450 mV
[ 2.752890] axp20_buck3: 700 <--> 3500 mV at 1300 mV
[ 2.762762] axp20_ldoio0: 1800 <--> 3300 mV at 2800 mV
[ 2.777512] input: axp20-supplyer as /devices/platform/sunxi-i2c.0/i2c-0/0-0034/axp20-supplyer.28/input/input0
[ 2.805312] axp20_ldo2: Failed to create debugfs directory
[ 2.815881] sunxi_wdt: sunxi WatchDog Timer Driver v1.0
[ 2.826168] sunxi_wdt: initialized (timeout=23s, nowayout=0)
[ 2.835851] device-mapper: uevent: version 1.0.3
[ 2.848273] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[ 2.861647] device-mapper: multipath: version 1.3.2 loaded
[ 2.872637] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 2.884732] device-mapper: multipath queue-length: version 0.1.0 loaded
[ 2.896901] device-mapper: multipath service-time: version 0.2.0 loaded
[ 2.906960] cpuidle: using governor ladder
[ 2.913949] cpuidle: using governor menu
[ 2.920193] [mmc-msg] sw_mci_init
[ 2.929271] [mmc-msg] MMC host used card: 0x9, boot card: 0x0, io_card 8
[ 2.941309] [mmc-msg] sdc0 set round clock 400000, src 24000000
[ 2.955498] [mmc-msg] sdc0 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 2.972586] [mmc-msg] sdc0 Probe: base:0xf0150000 irq:64 sg_cpu:f0152000(4fc00000) ret 0.
[ 2.985809] [mmc-msg] sdc3 set round clock 400000, src 24000000
[ 2.997273] ata1.00: ATA-8: SanDisk SDSSDHP256G, X2316RL, max UDMA/133
[ 3.005267] [mmc-msg] sdc3 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 3.027908] [mmc-msg] sdc3 Probe: base:0xf0154000 irq:67 sg_cpu:f0156000(4fc01000) ret 0.
[ 3.040578] [mmc_pm]: failed to fetch sdio card configuration!
[ 3.048741] sunxi_leds driver init
[ 3.055776] Registered led device: blue:ph21:led1
[ 3.064286] Registered led device: orange:ph20:led2
[ 3.072881] Registered led device: white:ph11:led3
[ 3.081391] Registered led device: green:ph07:led4
[ 3.091114] ledtrig-cpu: registered to indicate activity on CPUs
[ 3.101637] usbcore: registered new interface driver usbhid
[ 3.109977] usbhid: USB HID core driver
[ 3.115887] ashmem: initialized
[ 3.122492] logger: created 256K log 'log_main'
[ 3.130663] logger: created 256K log 'log_events'
[ 3.138905] logger: created 256K log 'log_radio'
[ 3.147154] logger: created 256K log 'log_system'
[ 3.157643] ata1.00: 500118192 sectors, multi 1: LBA48 NCQ (depth 31/32)
[ 3.168913] asoc: sndspdif <-> sunxi-spdif.0 mapping ok
[ 3.178003] ata1.00: configured for UDMA/133
[ 3.180541] [IIS]Entered sunxi_i2s_init
[ 3.192790] [I2S-0] sunxi_i2s_init I2S used in master mode
[ 3.201214] [IIS]Entered sunxi_i2s_dev_probe
[ 3.209905] [I2S-0] sndi2s_codec_init I2S used in master mode
[ 3.220158] [I2S-0] sndi2s_codec_probe I2S used in master mode
[ 3.228755] [IIS]Entered sunxi_sndi2s_init
[ 3.237263] [I2S-0] sunxi_sndi2s_init I2S used in master mode
[ 3.246832] asoc: sndi2s <-> sunxi-i2s.0 mapping ok
[ 3.254827] IPv4 over IPv4 tunneling driver
[ 3.261087] TCP: bic registered
[ 3.266485] TCP: cubic registered
[ 3.272307] TCP: westwood registered
[ 3.278474] TCP: highspeed registered
[ 3.284382] TCP: hybla registered
[ 3.289857] TCP: htcp registered
[ 3.295331] TCP: vegas registered
[ 3.300806] TCP: veno registered
[ 3.306540] TCP: scalable registered
[ 3.312101] TCP: lp registered
[ 3.317315] TCP: yeah registered
[ 3.323049] TCP: illinois registered
[ 3.329824] Initializing XFRM netlink socket
[ 3.337466] NET: Registered protocol family 10
[ 3.345292] NET: Registered protocol family 17
[ 3.353112] NET: Registered protocol family 15
[ 3.362141] [mmc_pm]: No sdio card, please check your config !!
[ 3.371692] Registering the dns_resolver key type
[ 3.378269] VFP support v0.3:
[ 3.388712] scsi 0:0:0:0: Direct-Access ATA SanDisk SDSSDHP2 X231 PQ: 0 ANSI: 5
[ 3.401813] implementor 41 architecture 2 part 30 variant 7 rev 4
[ 3.415059] sd 0:0:0:0: [sda] 500118192 512-byte logical blocks: (256 GB/238 GiB)
[ 3.426782] Registering SWP/SWPB emulation handler
[ 3.435723] sd 0:0:0:0: [sda] Write Protect is off
[ 3.443152] ehci_irq: port change detect
[ 3.451759] axp20_buck2: Failed to create debugfs directory
[ 3.461480] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.472564] [cpu_freq] INF:-------------------V-F Table-------------------
[ 3.487520] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.501619] [cpu_freq] INF: voltage = 1450mv frequency = 1008MHz
[ 3.513947] [cpu_freq] INF: voltage = 1425mv frequency = 912MHz
[ 3.521522] sda: sda1
[ 3.528786] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.538489] [cpu_freq] INF: voltage = 1350mv frequency = 864MHz
[ 3.549666] [cpu_freq] INF: voltage = 1250mv frequency = 720MHz
[ 3.560806] [cpu_freq] INF: voltage = 1150mv frequency = 528MHz
[ 3.571938] [cpu_freq] INF: voltage = 1100mv frequency = 312MHz
[ 3.583083] [cpu_freq] INF: voltage = 1050mv frequency = 144MHz
[ 3.594219] [cpu_freq] INF: voltage = 1000mv frequency = 0MHz
[ 3.606131] [cpu_freq] INF:-----------------------------------------------
[ 3.622739] [cpu_freq] INF:sunxi_cpufreq_initcall, get cpu frequency from sysconfig, max freq: 912MHz, min freq: 720MHz
[ 3.636132] ehci_irq: port change detect
[ 3.643890] registered taskstats version 1
[ 3.654315] [DISP] Invalid mode string: EDID:1280x720p60, ignoring
[ 3.673713] The port change to OHCI now!
[ 3.955912] [mmc-msg] mmc 0 detect change, present 1
[ 3.966242] usb 3-1: new full-speed USB device number 2 using sw-ohci
[ 4.184014] generic-usb 0003:1B1F:C00F.0001: hiddev0,hidraw0: USB HID v1.10 Device [eQ-3 HM-CFG-USB] on usb-sw-ohci-1/input0
[ 4.224244] Console: switching to colour frame buffer device 128x48
[ 4.297857] I2C: i2c-1: HDMI I2C adapter
[ 4.336222] axp20_buck3: incomplete constraints, leaving on
[ 4.346561] axp20_buck2: incomplete constraints, leaving on
[ 4.356807] axp20_ldo4: incomplete constraints, leaving on
[ 4.367016] axp20_ldo3: incomplete constraints, leaving on
[ 4.377184] axp20_ldo2: incomplete constraints, leaving on
[ 4.387365] axp20_ldo1: incomplete constraints, leaving on
[ 4.395739] console [netcon0] enabled
[ 4.402906] netconsole: network logging started
[ 4.411618] otg_wakelock_init: No USB transceiver found
[ 4.424363] sunxi-rtc sunxi-rtc: setting system clock to 2014-10-12 08:05:31 UTC (1413101131)
[ 4.434928] ALSA device list:
[ 4.440960] #0: sunxi-CODEC Audio Codec
[ 4.447246] #1: sunxi-sndspdif
[ 4.452484] #2: sunxi-sndi2s
[ 4.478980] [mmc-msg] sdc0 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 4.494225] [mmc-msg] sdc0 power on
[ 4.526040] [mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 4.555920] [mmc-msg] sdc0 set round clock 400000, src 24000000
[ 4.611703] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 4.624232] VFS: Mounted root (ext4 filesystem) on device 8:1.
[ 4.632895] devtmpfs: mounted
[ 4.638818] Freeing init memory: 216K
[ 4.648199] [mmc-err] smc 0 err, cmd 52, RTO
[ 4.656768] [mmc-err] smc 0 err, cmd 52, RTO
[ 4.669582] [mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 4.694183] [mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 4.711154] [mmc-err] smc 0 err, cmd 5, RTO
[ 4.719568] [mmc-err] smc 0 err, cmd 5, RTO
[ 4.727927] [mmc-err] smc 0 err, cmd 5, RTO
[ 4.736327] [mmc-err] smc 0 err, cmd 5, RTO
[ 4.749874] [mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 4.767790] [mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 4.791689] [mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 4.850702] [mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B
[ 4.870432] [mmc-msg] sdc0 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B
[ 4.889914] [mmc-msg] sdc0 set round clock 46153846, src 600000000
[ 4.959642] [mmc-msg] sdc0 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B
[ 4.973863] mmc0: new high speed SDHC card at address 8386
[ 4.994778] mmcblk0: mmc0:8386 SU04G 3.69 GiB
[ 5.004538] mmcblk0: p1
[ 5.444031] udevd[185]: starting version 175
[ 7.478506] EXT4-fs (sda1): Cannot change data mode on remount
[ 7.498957] EXT4-fs (sda1): Cannot change data mode on remount
[ 7.819535] Bluetooth: Core ver 2.16
[ 7.826667] NET: Registered protocol family 31
[ 7.836469] Bluetooth: HCI device and connection manager initialized
[ 7.846665] Bluetooth: HCI socket layer initialized
[ 7.855556] Bluetooth: L2CAP socket layer initialized
[ 7.864467] Bluetooth: SCO socket layer initialized
[ 7.888579] Bluetooth: HCI UART driver ver 2.2
[ 7.896820] Bluetooth: HCI H4 protocol initialized
[ 7.905553] Bluetooth: HCI BCSP protocol initialized
[ 7.914181] Bluetooth: HCILL protocol initialized
[ 7.927148] Bluetooth: HCIATH3K protocol initialized
[ 8.006816] pm: select wifi: ap6210
[ 8.013275] ap6xxx: config 32k clock
[ 8.020221] [wifi_pm]: wifi gpio init is OK !!
[ 8.030359] [rfkill]: rfkill set power 0
[ 8.122890] Bluetooth: RFCOMM TTY layer initialized
[ 8.132047] Bluetooth: RFCOMM socket layer initialized
[ 8.139914] Bluetooth: RFCOMM ver 1.11
[ 8.190234] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 8.246292] input: sunxi-ir as /devices/virtual/input/input1
[ 8.253710] IR Initial OK
[ 8.366240] [spi-err] Get spi devices number failed
[ 8.375888] [spi-err] register spi devices board info failed
[ 8.391176] spi: cannot find any using configuration for all 4 spi controllers, return directly!
[ 8.463350] bcmdhd: got gpio2, mapped to irqno170
[ 8.475062] dhd_customer_gpio_wlan_ctrl: call customer specific GPIO to turn on WL_REG_ON
[ 8.577116] sdio wifi power state: on
[ 8.588745] [mmc-msg] sdc3 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 8.613437] [mmc-msg] sdc3 power on
[ 8.646008] [mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 8.675902] [mmc-msg] sdc3 set round clock 400000, src 24000000
[ 8.724063] =========== WLAN placed in POWER ON ========
[ 8.763328] [mmc-err] smc 3 err, cmd 52, RTO
[ 8.771937] [mmc-err] smc 3 err, cmd 52, RTO
[ 8.784662] [mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 8.805494] [mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 8.819808] [mmc-err] smc 3 err, cmd 8, RTO
[ 8.832774] [mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 8.860146] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[ 8.871608] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 8.883069] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 8.895755] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[ 8.922943] [mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B
[ 8.940682] [mmc-msg] sdc3 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B
[ 8.955326] [mmc-msg] sdc3 set round clock 46153846, src 600000000
[ 9.025022] [mmc-msg] sdc3 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B
[ 9.040800] mmc1: new high speed SDIO card at address 0001
[ 9.049514] Linux Kernel SDIO/MMC Driver
[ 9.057377] bcmdhd: irq=170, flags=0x00000414
[ 9.066444] dhdsdio_probe : no mutex held. set lock
[ 9.075345] F1 signature read @0x18000000=0x1591a962
[ 9.083758] bcmsdh_config_hw_oob_intr: Enter
[ 9.096038] DHD: dongle ram size is set to 245760(orig 245760)
[ 9.104926] dhd_attach, firmware path
[ 9.113181] wl_create_event_handler thr:26e created
[ 9.121721] wl_create_event_handler thr:26e started
[ 9.133142] p2p0: P2P Interface Registered
[ 9.139157] bcm4330: exports duplicate symbol bcmsdh_probe (owned by bcmdhd)
[ 9.156264] bcm4330: exports duplicate symbol bcmsdh_probe (owned by bcmdhd)
[ 9.170296] dhd_attach thr:26f created
[ 9.176524] dhd_attach thr:26f started
[ 9.182778] dhd_attach thr:270 created
[ 9.188986] dhd_attach thr:270 started
[ 9.195233] dhd_attach thr:271 created
[ 9.202367] dhd_attach thr:271 started
[ 9.219431] Broadcom Dongle Host Driver: register interface [wlan0] MAC: 00:90:4c:11:22:33
[ 9.231787] dhdsdio_probe : the lock is released.
[ 9.249009]
[ 9.249027] Dongle Host Driver, version 1.28.23.3 (r)
[ 9.249034] Compiled in drivers/net/wireless/bcmdhd on Sep 26 2014 at 18:24:05
[ 9.276106] dhd_customer_gpio_wlan_ctrl: call customer specific GPIO to insert WLAN RESET
[ 9.383248] sdio wifi power state: off
[ 9.484947] =========== WLAN placed in RESET ========
[ 13.004214] sunxi_gmac: probed
[ 13.012748] eth0: PHY ID 001cc915 at 0 IRQ 0 (sunxi_gmac-0:00) active
[ 13.024007] eth0: PHY ID 001cc915 at 1 IRQ 0 (sunxi_gmac-0:01)
[ 15.037726] PHY: sunxi_gmac-0:00 - Link is Up - 1000/Full
[ 74.593580] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 74.603234] Bluetooth: BNEP filters: protocol multicast
root@cubie:/#
Das ganze in Code Tag verpackt damit es nicht ein meterlanger Post wird...
Ich habe die gleiche Image-Version und die Initialisierung von Bluetooth sieht bei mir in dmesg genau so aus wie bei Dir.
Das Einzige, was mir auffällt, ist die sehr lange Zeitspanne zwischen Sekunde 8 und Sekunde 74. Bei mir liegen da wenige Sekunden dazwischen. Irgendwas muss Deinen Systemstart massiv verzögern, wobei ich jetzt nicht sagen kann, ob das etwas mit Deinem nicht vorhandenen BT-Device zu tun hat.
[ 7.819535] Bluetooth: Core ver 2.16
[ 7.836469] Bluetooth: HCI device and connection manager initialized
[ 7.846665] Bluetooth: HCI socket layer initialized
[ 7.855556] Bluetooth: L2CAP socket layer initialized
[ 7.864467] Bluetooth: SCO socket layer initialized
[ 7.888579] Bluetooth: HCI UART driver ver 2.2
[ 7.896820] Bluetooth: HCI H4 protocol initialized
[ 7.905553] Bluetooth: HCI BCSP protocol initialized
[ 7.914181] Bluetooth: HCILL protocol initialized
[ 7.927148] Bluetooth: HCIATH3K protocol initialized
[ 8.122890] Bluetooth: RFCOMM TTY layer initialized
[ 8.132047] Bluetooth: RFCOMM socket layer initialized
[ 8.139914] Bluetooth: RFCOMM ver 1.11
[ 8.190234] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 74.593580] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 74.603234] Bluetooth: BNEP filters: protocol multicast
Was liefert denn die Ausgabe von lsmod?
Bei mir kommt:
Module Size Used by
cpufreq_userspace 3524 0
bnep 14462 2
bcmdhd 539724 0
spi_sun7i 19657 0
sunxi_ir 4037 0
hidp 17640 0
rfcomm 58686 10
bt_gpio 2741 0
wifi_gpio 6375 2 bcmdhd,bt_gpio
hci_uart 24876 1
bluetooth 264137 25 bnep,hidp,hci_uart,rfcomm
lsmod liefert
oot@cubie:/# lsmod
Module Size Used by
bnep 14462 2
cpufreq_userspace 3524 0
bcmdhd 539724 0
spi_sun7i 19657 0
sunxi_ir 4037 0
hidp 17640 0
rfcomm 58686 0
bt_gpio 2741 0
wifi_gpio 6375 2 bcmdhd,bt_gpio
hci_uart 24876 0
bluetooth 264137 12 bnep,hidp,hci_uart,rfcomm
schaut also auch ähnlich aus wie bei dir...
Vielleicht habe ich irgendein Paket übersehen welches ich installieren sollte, hast du für BT etwas spezielles installiert?
Nein, ich habe nichts zusätzliches installiert.
Hm, falls Du noch eine Idee hast - lass es mich wissen, ich bin ziemlich ratlos.
http://www.igorpecovnik.com/2013/12/24/cubietruck-debian-wheezy-sd-card-image/#new (http://www.igorpecovnik.com/2013/12/24/cubietruck-debian-wheezy-sd-card-image/#new)
Known bugs or limitations
On board Bluetooth firmware loading sometime fail. Reboot helps.
@fruit: hat mit dem hier beschriebenen Problem nichts zu tun. Wenn das Laden der Firmware fehlschlägt, gibt es eine Meldung im Log. Das ist hier aber nicht der Fall.
Heute morgen startete ich den Cube neu - und siehe da, ohne weiteres zu tun wurden unsere Mobiltelefone erkannt und gefunden... Also war der Reboot tip doch gut.
@Udo: Hast du eine Idee wie ich -
nach dem booten überwachen könnte ob Bluetooth verfügbar ist?
Falls nicht eine Warnung ins Fhemlog und oder gegebenenfalls neu starten könnte..?
Zitat von: der-Lolo am 24 Oktober 2014, 13:34:27
Heute morgen startete ich den Cube neu - und siehe da, ohne weiteres zu tun wurden unsere Mobiltelefone erkannt und gefunden... Also war der Reboot tip doch gut.
Sei Dir da mal nicht so sicher. Igor hat im aktuellen Image das Laden der Bluetooth-Firmware wieder komplett ausgebaut. Ich betrachte das integrierte Bluetooth im Cubietruck nach wie vor als "very experimental" und würde für eine tatsächliche Anwendung immer einen USB-BT-Stick verwenden.
Ja, ich habe die unzuverlässigkeit bemerkt - und bin derzeit per collectcord und dem altem beagle bone unterwegs. Ein zusätzlicher Stick ist bestellt.
Hat sich am aktuellem Image was geändert?
Keine entscheidenden Änderungen. Bluetooth Sticks habe ich hier noch irgendwo jede Menge rumliegen...
Hallo Udo,
der Stick ist nun da, es ist ein Inatek BTA-CSR4B5.
Kannst du mir kurz beschreiben was ich nun tun muss um den anstelle des onboard Bluetooth zu nutzen?
Einfach einstecken? Ist das Plug & Play oder brauche ich einen Treiber?
Wie teile ich dem hcitool mit welchen Schnittstelle es nutzen soll?
Onboard würde ich dann auch gerne ausschalten - wir sind zwar ja eh schon verstrahlt, aber notwendig ist es ja dann nicht mehr.
Wäre cool wenn Du kurz unterstützt.
reinstecken und geht - zumindest hier bei mir.
Eventuell musst Du das bt-Modul in der /etc/modules auskommentieren (vermutlich bt-gpio)
Bin gerade über eine google suche auf diesen Fred gestossen. Für dein cubietruck mit geleadenen Treibern, was bei Igor Images der Fall sein soll, veruch doch mal bitte "hciattach /dev/ttyS1 any"
Gibt es inzwischen eine zuverlässige Methode das integrierte Bluetooth Modul des Cubietrucks zu nutzen?
mit aktuellem image sollte es keine probleme geben, hatte zumindest keine und einige geräte (smartphone und handys) verbunden.
Zitat von: chris1284 am 30 März 2015, 15:09:52
mit aktuellem image sollte es keine probleme geben, hatte zumindest keine und einige geräte (smartphone und handys) verbunden.
Wie konntest du Bluetooth nutzen? Bei mir geht es trotz aktuellen Image leider nicht.
Das würde mich auch interessieren. Ich habe Bluez installiert und es funktioniert leider trotzdem nicht. -.-
Mein letzter stand war das es funktionierte, aber eben leider nicht zuverlässig - also investierte ich die 7€ für einen BT4.0 stick...
hcitool und bluetooth-agent meine ich habe ich damals die devices gekoppelt
ihr habt auch das auf igors seite gelsen ?
ZitatBluetooth ready (working with on-board device / disabled by default – insserv brcm40183-patch)
ihr müsst bt im aktuellen image wohl erst noch aktivieren und ansonsten läufts wohl weiter hin mit dem zusatz
ZitatOn board Bluetooth firmware loading sometime fail. Reboot helps. Better solution is under development
was bei mir aber immer klappte (bei den 3-4 reboots aufs halbe jahr gesehen....
Zitat von: chris1284 am 30 März 2015, 17:45:21
ihr habt auch das auf igors seite gelsen ?ihr müsst bt im aktuellen image wohl erst noch aktivieren und ansonsten läufts wohl weiter hin mit dem zusatzwas bei mir aber immer klappte (bei den 3-4 reboots aufs halbe jahr gesehen....
Kennst du eine Anleitung wie man diesen Patch einspielt und wo dieser zufinden ist?
ich meine
Zitatinsserv brcm40183-patch
ist der befehl das modul zu aktivieren... http://www.fibel.org/linux/lfo-0.6.0/node322.html
ich hatte als letzt verison eine davor, wo bt per default aktiv war. ich kann den cubi morgen mal booten und nochmal nachsehen
wie sind denn Eure Erfahrungen in Bezug auf Reichweite des eingebauten BT Modules im CT?
Im Vergleich zu einem USB BT Dongle ist die Reichweite deutlich schlechter.
Wie sind Eure Erfahrungen?