Bei meinen beiden Winmatic zeigt sich seit einiger Zeit ein "state: unreachable".
Die Geräte funktionieren einwandfrei, führt man einen Befehl aus, erscheint dann auch ein "done".
Ursächlich erscheint mir der "statusrequest", dieser scheint kein Ergebnis zu liefern.
LOG
2015.08.30 14:47:40 5: CUL_HM AZ_Winmatic protEvent:CMDs_pending pending:1
2015.08.30 14:47:40 5: CUL_HM AZ_Winmatic protEvent:CMDs_pending pending:2
2015.08.30 14:47:40 3: CUL_HM set AZ_Winmatic statusRequest
2015.08.30 14:47:40 5: CUL_HM AZ_Winmatic protEvent:CMDs_processing... pending:1
2015.08.30 14:47:41 5: CUL_HM AZ_Winmatic protEvent:CMDs_processing... pending:1
2015.08.30 14:47:41 5: CUL_HM AZ_Winmatic sent ACK:2
2015.08.30 14:47:41 4: CUL_HM AZ_Winmatic dupe: dont process
2015.08.30 14:47:41 5: CUL_HM AZ_Winmatic protEvent:CMDs_processing... pending:0
2015.08.30 14:47:41 5: CUL_HM AZ_Winmatic protEvent:CMDs_done
2015.08.30 14:47:41 5: CUL_HM AZ_Winmatic sent ACK:2
2015.08.30 14:47:42 4: CUL_HM AZ_Winmatic dupe: dont process
Readings
D-firmware 1.6
D-serialNr KEQ0720996
PairedTo 0x1EA01F
R-intKeyVisib invisib
R-keypressSignal on
R-pairCentral 0x1EA01F
R-signal on
R-signalTone low
RegL_00: 02:01 03:19 0A:1E 0B:A0 0C:1F 00:00
aesCommToDev ok
aesKeyNbr 00
state unreachable
Der statusrequest wird, wie eingestellt, alle 30min durchgeführt und "belastet" das LOG-File.
Hat jemand eine Idee, danke.
kannst du es einmal loggen? Also einen statusrequest?
wenn wimatic das kommando nicht kann werde ich es entfernen und alles ist gut.
Welche Version des winmatic hast du ?
LOG statusrequest Winmatic
2015.08.30 17:15:59 5: CUL_HM AZ_Winmatic protEvent:CMDs_pending pending:1
2015.08.30 17:15:59 5: CUL_HM AZ_Winmatic protEvent:CMDs_pending pending:2
2015.08.30 17:15:59 3: CUL_HM set AZ_Winmatic statusRequest
2015.08.30 17:15:59 5: CUL_HM AZ_Winmatic protEvent:CMDs_processing... pending:1
2015.08.30 17:16:03 4: CUL_HM_Resend: AZ_Winmatic nr 2
2015.08.30 17:16:07 5: CUL_HM AZ_Winmatic protEvent:CMDs_done_Errors:1
Firmware ist 1.6
jetzt gibt es kein StatusRequest mehr. Die anderen Detail sollten folgeerscheinungen sein und somit verschwunden.
Hallo, auch mit der neuen Version macht die Winmatic beim Serverstart und dann alle 30min Ihren statusrequest.
das Kommando statusrequest sollte es nicht mehr geben.
mache ein get ... cmdList.
wenn noch ein statusRequest auftaucht stimmt deine Version nicht
Hallo,
mein Fehler, ich hatte nur die 10_CUL_HM.pm, nicht jedoch die HMConfig.pm aktualisiert.
Jetzt funktioniert es.
Danke