Hallo Zusammen,
nachdem es nun doch Nachts wieder kühl ist, wollte ich die Heizung anschmeißen.
Leider schaltet das HCS Modul nun nicht mehr das definierte Device.
Weder an noch aus.
Eigentlich wurde daran nichts verändert??
Hier das List vom HCS:
Internals:
DEF Vaillant
NAME HCS_System
NEXTCHECK 00:40:26
NR 299
STATE idle
TYPE HCS
Readings:
2016-10-05 00:35:20 FHT_0a54 ignored
2016-10-01 15:48:07 FHT_4eb1 ignored
2016-10-01 15:48:07 FHT_5e75 ignored
2016-10-05 00:35:20 FHT_Hobbyraum idle
2016-10-05 00:35:20 FHT_Kellerflur idle
2016-10-05 00:35:20 FHT_Waschkeller idle
2016-10-05 00:35:20 HZ_Bad idle
2016-10-05 00:35:20 HZ_Buero idle
2016-10-05 00:35:20 HZ_Carlotta idle
2016-10-05 00:35:20 HZ_Couch idle
2016-10-05 00:35:20 HZ_Dachboden idle
2016-10-05 00:35:20 HZ_Esstisch idle
2016-10-05 00:35:20 HZ_Flur_oben idle
2016-10-05 00:35:20 HZ_Flur_unten idle
2016-10-05 00:35:20 HZ_Klo idle
2016-10-05 00:35:20 HZ_Kueche idle
2016-10-05 00:35:20 HZ_Leoni idle
2016-10-05 00:35:20 HZ_Schlafzimmer idle
2016-10-05 00:28:19 device Vaillant
2016-10-05 00:35:20 eco off
2016-10-05 00:35:20 locked 00:00:00
2016-10-05 00:35:20 overdrive off
2016-10-05 00:35:20 state idle
Helper:
Device:
Fht_0a54:
actuator 0
demand 0
excluded 1
ignored 1
tempDesired n/a
tempMeasured n/a
type FHT
Fht_hobbyraum:
actuator 0
demand 0
excluded 0
ignored 0
tempDesired 14.0
tempMeasured 18.1
type FHT
Fht_kellerflur:
actuator 60
demand 0
excluded 0
ignored 0
tempDesired 14.0
tempMeasured 17.7
type FHT
Fht_waschkeller:
actuator 0
demand 0
excluded 0
ignored 0
tempDesired 14.0
tempMeasured 18.4
type FHT
Hz_bad:
actuator 0
demand 0
excluded 0
ignored 0
tempDesired 16.0
tempMeasured 20.8
type CUL_HM
Hz_buero:
actuator 98
demand 0
excluded 0
ignored 0
tempDesired 14.0
tempMeasured 19.7
type CUL_HM
Hz_carlotta:
actuator 0
demand 0
excluded 0
ignored 0
tempDesired 8.0
tempMeasured 18.6
type CUL_HM
Hz_couch:
actuator 0
demand 0
excluded 0
ignored 0
tempDesired 16.0
tempMeasured 20.9
type CUL_HM
Hz_dachboden:
actuator 0
demand 0
excluded 0
ignored 0
tempDesired 16.0
tempMeasured 19.8
type CUL_HM
Hz_esstisch:
actuator 0
demand 0
excluded 0
ignored 0
tempDesired 16.0
tempMeasured 20.9
type CUL_HM
Hz_flur_oben:
actuator 0
demand 0
excluded 0
ignored 0
tempDesired 16.0
tempMeasured 20.8
type CUL_HM
Hz_flur_unten:
actuator 0
demand 0
excluded 0
ignored 0
tempDesired 16.0
tempMeasured 20.8
type CUL_HM
Hz_klo:
actuator 0
demand 0
excluded 0
ignored 0
tempDesired 16.0
tempMeasured 20.3
type CUL_HM
Hz_kueche:
actuator 0
demand 0
excluded 0
ignored 0
tempDesired 16.0
tempMeasured 20.9
type CUL_HM
Hz_leoni:
actuator 0
demand 0
excluded 0
ignored 0
tempDesired 8.0
tempMeasured 19.4
type CUL_HM
Hz_schlafzimmer:
actuator 0
demand 0
excluded 0
ignored 0
tempDesired 8.0
tempMeasured 18.0
type CUL_HM
Attributes:
alias Vaillant Steuerung
devStateIcon demand:sani_heating_temp idle:sani_heating_manual off:general_aus
deviceCmdOff off
deviceCmdOn on
event-on-change-reading .*
exclude FHT_0a54,FHT_4eb1,FHT_5e75
icon sani_heating_manual
idleperiod 5
interval 5
mode thermostat
room Heizung
thermostatThresholdOff 0.1
thermostatThresholdOn 0.2
valveThresholdOff 35
valveThresholdOn 40
verbose 3
und hier das List des zu schalteten Device:
Internals:
.triggerUsed 1
DEF 39212B
HMLan_MSGCNT 6
HMLan_RAWMSG R91D2DCF4,0001,16A9CBD5,FF,FFBD,06800239212B26E9A00101C80047
HMLan_RSSI -67
HMLan_TIME 2016-10-05 00:31:38
IODev HMLan
LASTInputDev HMLan
MSGCNT 6
NAME Vaillant
NOTIFYDEV global
NR 298
NTFY_ORDER 50-Vaillant
STATE on
TYPE CUL_HM
lastMsg No:06 - t:02 s:39212B d:26E9A0 0101C80047
protLastRcv 2016-10-05 00:31:38
protSnd 6 last_at:2016-10-05 00:31:37
protState CMDs_done
rssi_HMLan max:-61 avg:-70 lst:-71 min:-74 cnt:5
rssi_at_HMLan max:-67 lst:-67 avg:-69.5 min:-72 cnt:6
Readings:
2016-10-05 00:31:38 .protLastRcv 2016-10-05 00:31:38
2016-10-05 00:31:38 CommandAccepted yes
2016-09-30 14:13:18 D-firmware 1.6
2016-10-05 00:31:38 battery ok
2016-10-05 00:31:38 deviceMsg on (to VCCU)
2016-10-05 00:31:38 level 100
2016-10-05 00:31:38 pct 100
2016-10-05 00:31:38 recentStateType ack
2016-10-05 00:31:38 state on
2016-10-05 00:31:38 timedOn off
Helper:
HM_CMDNR 6
cSnd 1126E9A039212B0201000000,1126E9A039212B0201C80000
dlvlCmd ++A01126E9A039212B0201C80000
mId 006C
rxType 2
Expert:
def 1
det 0
raw 1
tpl 0
Io:
newChn +39212B,00,01,00
nextSend 1475620298.24732
rxt 0
vccu VCCU
p:
39212B
00
01
00
Mrssi:
mNo 06
Io:
HMLan -65
Prt:
bErr 0
sProc 0
Rspwait:
Q:
qReqConf 00
qReqStat
Role:
chn 1
dev 1
prs 1
Rssi:
Hmlan:
avg -70
cnt 5
lst -71
max -61
min -74
At_hmlan:
avg -69.5
cnt 6
lst -67
max -67
min -72
Shadowreg:
Tmpl:
Attributes:
IODev HMLan
IOgrp VCCU
alias Vaillant Therme
autoReadReg 4_reqStatus
devStateIcon on:ios-on-green off:ios-off
event-on-change-reading state
expert 2_full
firmware 1.6
group HCS
icon sani_boiler_temp
model HM-LC-SW1-BA-PCB
msgRepeat 1
peerIDs 00000000,
room Heizung
subType switch
verbose 0
webCmd on:off
Geht denn ein
set Vaillant on
und
set Vaillant off
?
Das wäre das, was HCS rausschicken würde.
Die Thresholds sind sehr eng - wenn also eins deiner Thermostate eine Soll-Temperatur nur 0,1°C über der Ist-Temperatur meldet (und der letzte Schaltvorgang mind. 5 min her ist), soll die Therme einschalten - und bei nur 0,2°C über der Soll-Temperatur wieder ausschalten? 0,3°C Unterschied als Gesamtspanne find ich nicht viel, und 5min als letzter Schaltzeitpunkt auch nicht...
ein set Vaillant on oder off geht.
Ich habe jetzt umgestellt auf mode Valve und die ignored Devices rausgeschmissen, jetzt geht es wieder.
Sehr komisch.
Hm... und jetzt wieder zurück auf thermostat mode?
Ich start meinen Fhem so 1x die Woche neu durchschnittlich - da krieg ich mögliche "Verschlucker" nicht so mit... Das Log sagt nix zur Ausstiegszeit?