Originally posted by: <email address deleted>
Hallo Maz,
ich denke du bis der richtige Ansprechpartner.
Sobald ein Rollo angesteuert wird, das die Position schon erreicht hat wird
die Positionen auf 0% Gesetz.
Da das KNX Sytem aber nur Änderung Sendet und das 10_EIB.pm keine Daten
aktiv anfordern. Ist die Darstellung im fhem falsch.
Der Prozentwert ist immer auf 0% auch wenn der Rollo 100% geschlossen ist.
Anbei die fhem Konfig wie sie im fhem.cfg Steht (genauer gesagt in der
Auslagerungsdatei).
Erklärung zu den GAs:
0/0/x7 => Prozentuale Positionswert.
0/0/x0 => auf/ab Bewegung
0/0/x1 => Stopp
0/0/x2 => Position 1&2 (low/high)
0/0/x3 => Position 3&4 (low(high
#Rollo Steuerung
define RBUERO1 EIB 0/0/17 0/0/10 0/0/11 0/0/12 0/0/13
attr RBUERO1 alias Rollo 1 Arbeitszimmer
attr RBUERO1 eventMap /on g3:Stop/off g2:Auf/on g2:Ab/off g4:Pos1/on
g4:Pos2/off g5:Pos3/on g5:Pos4
attr RBUERO1 model percent255
attr RBUERO1 room Rollos
attr RBUERO1 webCmd Auf:Stop:Ab:::Pos1:Pos2:Pos3:Pos4
define RBUERO2 EIB 0/0/27 0/0/20 0/0/21 0/0/22 0/0/23
attr RBUERO2 alias Rollo 2 Arbeitszimmer
attr RBUERO2 eventMap /on g3:Stop/off g2:Auf/on g2:Ab/off g4:Pos1/on
g4:Pos2/off g5:Pos3/on g5:Pos4
attr RBUERO2 model percent255
attr RBUERO2 room Rollos
attr RBUERO2 webCmd Auf:Stop:Ab:::Pos1:Pos2:Pos3:Pos4
define BadOG EIB 0/0/37 0/0/30 0/0/31 0/0/32 0/0/33
attr BadOG eventMap /on g3:Stop/off g2:Auf/on g2:Ab/off g4:Pos1/on
g4:Pos2/off g5:Pos3/on g5:Pos4
attr BadOG model percent255
attr BadOG room Rollos
attr BadOG webCmd Auf:Stop:Ab:::Pos1:Pos2:Pos3:Pos4
define Flur1 EIB 0/0/47 0/0/40 0/0/41 0/0/42 0/0/43
attr Flur1 alias Flur 1 OG
attr Flur1 eventMap /on g3:Stop/off g2:Auf/on g2:Ab/off g4:Pos1/on
g4:Pos2/off g5:Pos3/on g5:Pos4
attr Flur1 fp_1OG 50,400,2,
attr Flur1 model percent255
attr Flur1 room Rollos
attr Flur1 webCmd Auf:Stop:Ab:::Pos1:Pos2:Pos3:Pos4
Gruß
lo4dro
--
To unsubscribe from this group, send email to
fhem-users+unsubscribe@googlegroups.com