Hallo Zusammen,
einer meiner Bewegungsmelder HM-SEC-MDIR zickt seit ein paar Wochen ziemlich rum und meldet ständig Bewegung, obwohl da definitiv nichts ist.
Dachte erst, es liegt evtl. an Helligkeitsveränderungen.
Deswegen habe ich die Lage mal verändert, das sollte passen.
Dann habe ich den Wert R-brightFilter auf 5 gesetzt, alles ohne Abhilfe.
Ist das Ding defekt, oder kann ich noch was machen?
Hier list:
Internals:
DEF 1A503C
HMLan2_MSGCNT 28
HMLan2_RAWMSG E1A503C,0000,0CAE9E59,FF,FFC6,87A6101A503C26E9A006012400
HMLan2_RSSI -58
HMLan2_TIME 2018-01-19 11:08:44
HMLan_MSGCNT 28
HMLan_RAWMSG E1A503C,0000,051FCC6D,FF,FFD6,87A6101A503C26E9A006012400
HMLan_RSSI -42
HMLan_TIME 2018-01-19 11:08:44
IODev HMLan
LASTInputDev HMLan2
MSGCNT 56
NAME Bewegung_FlurUnten
NOTIFYDEV global
NR 554
NTFY_ORDER 50-Bewegung_FlurUnten
STATE noMotion
TYPE CUL_HM
lastMsg No:87 - t:10 s:1A503C d:26E9A0 06012400
protLastRcv 2018-01-19 11:08:44
protSnd 20 last_at:2018-01-19 11:08:44
protState CMDs_done
rssi_at_HMLan cnt:28 min:-42 lst:-42 max:-42 avg:-42
rssi_at_HMLan2 avg:-58 max:-58 min:-58 cnt:28 lst:-58
READINGS:
2018-01-08 08:56:52 .RegL_00. 02:01 0A:26 0B:E9 0C:A0 10:01 00:00
2018-01-08 08:56:52 .RegL_01. 01:12 02:50 08:01 22:C8 00:00
2018-01-08 08:56:53 .peerListRDate 2018-01-08 08:56:53
2018-01-19 11:08:44 .protLastRcv 2018-01-19 11:08:44
2018-01-19 09:28:52 Activity alive
2016-10-25 15:33:41 D-firmware 1.0
2016-10-25 15:33:41 D-serialNr JEQ0155759
2018-01-08 08:56:52 PairedTo 0x26E9A0
2017-12-30 13:26:28 R-brightFilter 5
2017-12-30 13:26:28 R-captInInterval off
2017-12-30 13:26:28 R-evtFltrNum 1
2017-12-30 13:26:28 R-evtFltrPeriod 1 s
2017-12-30 13:26:28 R-ledOnTime 1 s
2017-12-30 13:26:28 R-minInterval 15
2017-12-30 13:26:27 R-pairCentral 0x26E9A0
2017-12-30 13:26:27 R-sabotageMsg on
2017-12-30 13:26:28 R-sign on
2018-01-19 11:08:44 battery ok
2018-01-19 11:08:44 brightness 36
2018-01-19 11:08:44 cover closed
2018-01-19 11:04:49 motion off
2018-01-19 11:04:32 motionCount 189_next:15s
2018-01-19 11:04:49 motionDuration 17
2018-01-08 08:47:26 powerOn 2018-01-08 08:47:26
2018-01-19 11:08:44 recentStateType info
2018-01-19 11:04:49 state noMotion
2018-01-19 11:04:32 trigger_cnt 189
helper:
HM_CMDNR 135
mId 004A
regLst ,0,1,4p
rxType 28
supp_Pair_Rep 0
ack:
expert:
def 1
det 1
raw 0
tpl 0
io:
newChn +1A503C,00,01,00
nextSend 1516356524.86223
rxt 2
vccu VCCU
p:
1A503C
00
01
00
mRssi:
mNo 87
io:
HMLan -40
HMLan2 -58
prt:
bErr 0
sProc 0
sleeping 0
rspWait:
q:
qReqConf
qReqStat
role:
chn 1
dev 1
rpt:
IO HMLan
flg A
ts 1516356524.77515
ack:
HASH(0x61f8b20)
87800226E9A01A503C01012400
rssi:
at_HMLan:
avg -42
cnt 28
lst -42
max -42
min -42
at_HMLan2:
avg -58
cnt 28
lst -58
max -58
min -58
tmpl:
Attributes:
DbLogExclude .*
IODev HMLan
IOgrp VCCU
actCycle 000:20
actStatus alive
alias Flur unten
autoReadReg 5_readMissing
devStateIcon motion:message_presence@red noMotion:message_presence_disabled
event-on-change-reading battery,cover,motion,state
expert 1_allReg
firmware 1.0
group Bewegungsmelder
icon people_sensor
model HM-SEC-MDIR
peerIDs 00000000,
room Alarme,Flur
serialNr JEQ0155759
subType motionDetector
Aber da steht doch noMotion ;)
Zitat von: tiroso am 19 Januar 2018, 11:18:15
Aber da steht doch noMotion ;)
Gerade mal kurz ;D
Sicher, dass kein Infrarotsender oder ähnliches in der Nähe ist oder ein anderer Funker den Sensor beeinflusst?
ziemlich (nicht 100%) sicher, aber werde ich auch mal checken.