Von Rosenstein & Söhne gibt es ein Digitales Kühl- & Gefrierschrank-Thermometer das ich gerne in FHEM einbinden möchte. Kann Signalduino die Werte dieses Thermometers empfangen?
Ja , heute gerade gemacht.
.... Antwort auch wenn die Frage ,,Uralt" ist ....
Einfach die Thermometer mit Autocreate mit in FHEM aufgenommen. Problemlos!
Hallo ,
habe meinen NanoCul auf SIGNALduino geflasht .
Wollte meine Rosenstein & Söhne Thermometer in Fhem einbinden.
Leider kommt über Autocreate nichts rein .
Kann der SIGNALduino mit NC3911 arbeiten ?
Danke
laut Modul: ja
ZitatRosenstein & Soehne, PEARL NC-3911, NC-3912, refrigerator thermometer - 2 channels
# https://github.com/RFD-FHEM/RFFHEM/issues/504 - Support for NC-3911 Fridge Temp, MoskitoHorst, 2019-02-05
Danke für die Antwort .
Ich wollte als Attribut den "rfmode" Slow RF setzen , da der Nano auf 433 läuft
ZitatERROR: This attribute is only available for a receiver with CC1101
Komischerweise ist es ein CC1101
Das list sieht so aus :
ZitatInternals:
Clients :CUL_EM:CUL_FHTTK:CUL_TCM97001:CUL_TX:CUL_WS:Dooya:FHT:FLAMINGO:FS10:FS20: :Fernotron:Hideki:IT:KOPP_FC:LaCrosse:OREGON:PCA301:RFXX10REC:Revolt:SD_AS:SD_Rojaflex: :SD_BELL:SD_GT:SD_Keeloq:SD_RSL:SD_UT:SD_WS07:SD_WS09:SD_WS:SD_WS_Maverick:SOMFY: :Siro:SIGNALduino_un:
DEF /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0@57600
DMSG nothing
DevState initialized
DeviceName /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0@57600
FD 16
FUUID 64eb8200-f33f-cfd3-1175-3c32d992e3ede904
IDsNoDispatch 2,72.1,82
LASTDMSG nothing
LASTDMSGID nothing
NAME Nano
NR 175
PARTIAL
STATE opened
TIME 1693159703.36954
TYPE SIGNALduino
eventCount 15
sendworking 0
version V 3.5.0 SIGNALduino - compiled at Jul 8 2022 18:09:56
versionProtocols 1.52
versionmodul 3.5.5+20230815
MatchList:
10:SD_WS07 ^P7#[A-Fa-f0-9]{6}[AFaf][A-Fa-f0-9]{2,3}
11:SD_WS09 ^P9#F[A-Fa-f0-9]+
12:SD_WS ^W\d+x{0,1}#.*
13:RFXX10REC ^(20|29)[A-Fa-f0-9]+
14:Dooya ^P16#[A-Fa-f0-9]+
15:SOMFY ^Ys[0-9A-F]+
16:SD_WS_Maverick ^P47#[A-Fa-f0-9]+
17:SD_UT ^P(?:14|20|24|26|29|30|34|46|56|68|69|76|78|81|83|86|90|91|91.1|92|93|95|97|99|104|105|114|118|121)#.*
18:FLAMINGO ^P13\.?1?#[A-Fa-f0-9]+
19:CUL_WS ^K[A-Fa-f0-9]{5,}
1:IT ^i......
20:Revolt ^r[A-Fa-f0-9]{22}
21:FS10 ^P61#[A-F0-9]+
22:Siro ^P72#[A-Fa-f0-9]+
23:FHT ^81..(04|09|0d)..(0909a001|83098301|c409c401)..
24:FS20 ^81..(04|0c)..0101a001
25:CUL_EM ^E0.................
26:Fernotron ^P82#.*
27:SD_BELL ^P(?:15|32|41|42|57|79|96|98|112)#.*
28:SD_Keeloq ^P(?:87|88)#.*
29:SD_GT ^P49#[A-Fa-f0-9]+
2:CUL_TCM97001 ^s[A-Fa-f0-9]+
30:LaCrosse ^(\S+\s+9 |OK\sWS\s)
31:KOPP_FC ^kr\w{18,}
32:PCA301 ^\S+\s+24
33:SD_Rojaflex ^P109#[A-Fa-f0-9]+
3:SD_RSL ^P1#[A-Fa-f0-9]{8}
4:OREGON ^(3[8-9A-F]|[4-6][0-9A-F]|7[0-8]).*
5:CUL_TX ^TX..........
6:SD_AS ^P2#[A-Fa-f0-9]{7,8}
7:Hideki ^P12#75[A-F0-9]+
9:CUL_FHTTK ^T[A-F0-9]{8}
X:SIGNALduino_un ^\d+#.*
OLDREADINGS:
QUEUE:
READINGS:
2023-08-27 20:34:31 ping OK
2023-08-27 20:08:30 state opened
additionalSets:
keepalive:
ok 1
retry 0
mcIdList:
10
11
12
18
43
47
52
57
58
96
119
129
mnIdList:
100
101
102
103
107
107.1
108
109
112
115
116
116.1
117
123
125
126
msIdList:
0
0.1
0.2
0.3
0.4
0.5
1
3
3.1
4
6
7
7.1
13
13.2
14
15
17
20
23
25
33
33.1
33.2
35
41
49
51
53
54.1
55
65
68
74.1
87
88
90
91.1
93
106
113
118.1
muIdList:
8
9
13.1
16
17.1
19
20.1
21
22
24
26
27
28
29
30
31
32
34
36
37
38
39
40
42
44
44.1
45
46
48
49.1
49.2
50
54
56
59
60
61
62
64
66
67
69
70
71
72
73
74
76
78
79
80
81
83
84
85
86
89
91
92
94
95
97
98
99
104
105
110
111
114
118
120
121
122
Attributes:
hardware nanoCC1101
room Empfänger
updateChannelFW stable
verbose 4
Zitatversion V 3.5.0 SIGNALduino - compiled at Jul 8 2022 18:09:56
Da bei der version kein "cc1101" enthalten ist, wurde die falsche firmware geflasht oder der cc1101 wurde nicht erkannt.
ZitatKann der SIGNALduino mit NC3911 arbeiten ?
Wenn man in der Protokolliste nach dem NC-3911 sucht, findet man ihn bei der Protokol Id 38
https://ralf9.github.io/SD_Device_Proto.html
Gruß Ralf
Hallo Ralf ,
Danke für Deine Antwort .
Ich habe als Anleitung zum flashen das Fhem Wiki benutzt
Zitathttps://wiki.fhem.de/wiki/SIGNALduino#Flashen_des_Arduino_mit_der_SIGNALduino_Firmware
Könntest DU mir sagen wie und wo ich die Version
Zitatv3.4.16
bekomme ?
Danke
Die v3.4.16 ist die aktuelle Version von meiner Variante des 00_SIGNALDuino fhem Moduls.
Bei Dir ist aber das Problem evtl die firmware.
Bitte flashe mal damit die firmware "SIGNALDuino_nanocc1101_3.5.0.hex":
set Nano flash https://github.com/RFD-FHEM/SIGNALDuino/releases/download/3.5.0/SIGNALDuino_nanocc1101_3.5.0.hex
Gruß Ralf
Das habe ich gerade gemacht
Zitatset Nano flash https://github.com/RFD-FHEM/SIGNALDuino/releases/download/3.5.0/SIGNALDuino_nanocc1101_3.5.0.hex
Im list steht aber immer noch
Zitatversion
V 3.5.0 SIGNALduino - compiled at Jul 8 2022 18:09:56
ZitatInternals:
Clients :CUL_TCM97001:SD_WS:SD_WS07:SD_WS09:Hideki:LaCrosse:OREGON:CUL_EM:CUL_WS:CUL_TX:SD_AS:IT: :FS10:FS20:SOMFY:FLAMINGO:SD_WS_Maverick:KOPP_FC:PCA301:SD_BELL:SD_GT:SD_RSL:SD_UT:WMBUS:HMS: :IFB:CUL_FHTTK:FHT:RFXX10REC:Revolt:Dooya:Fernotron:SD_Keeloq:SD_Rojaflex:Siro:LTECH:SD_Tool:SIGNALduino_un:
ClientsKeepOrder 1
DEF /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0@57600
DMSG nothing
DevState initialized
DeviceName /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0@57600
FD 16
FUUID 64eb8200-f33f-cfd3-1175-3c32d992e3ede904
IDsNoDispatch 2,43.1,72.1,82,87,88
LASTDMSG nothing
LASTDMSGID nothing
NAME Nano
NR 175
PARTIAL
STATE opened
TIME 1693233767.09097
TYPE SIGNALduino
eventCount 13
sendworking 0
version V 3.5.0 SIGNALduino - compiled at Jul 8 2022 18:09:56
versionmodul v3.4.16-dev_ralf_23.07.
versionprotoL v3.4.16-dev_ralf_23.07.
MatchList:
01:IT ^i......
02:CUL_TCM97001 ^s[A-Fa-f0-9]+
03:SD_RSL ^P1#[A-Fa-f0-9]{8}
04:OREGON ^(3[8-9A-F]|[4-6][0-9A-F]|7[0-8]).*
05:CUL_TX ^TX..........
06:SD_AS ^P2#[A-Fa-f0-9]{7,8}
07:Hideki ^P12#75[A-F0-9]+
09:CUL_FHTTK ^T[A-F0-9]{8}
10:SD_WS07 ^P7#[A-Fa-f0-9]{6}[AFaf][A-Fa-f0-9]{2,3}
11:SD_WS09 ^P9#F[A-Fa-f0-9]+
12:SD_WS ^W\d+x{0,1}#.*
13:RFXX10REC ^(20|29)[A-Fa-f0-9]+
14:Dooya ^P16#[A-Fa-f0-9]+
15:SOMFY ^Ys[0-9A-F]+
16:SD_WS_Maverick ^P47#[A-Fa-f0-9]+
17:SD_UT ^P(?:14|20|24|26|29|30|34|46|56|68|69|76|78|81|83|86|90|91|91.1|92|93|95|97|99|104|105|114|118|121|124|127|128|199)#.*
18:FLAMINGO ^P13\.?1?#[A-Fa-f0-9]+
19:CUL_WS ^K[A-Fa-f0-9]{5,}
20:Revolt ^r[A-Fa-f0-9]{22}
21:FS10 ^P61#[A-F0-9]+
22:Siro ^P72#[A-Fa-f0-9]+
23:FHT ^81..(04|09|0d)..(0909a001|83098301|c409c401)..
24:FS20 ^81..(04|0c)..0101a001
25:CUL_EM ^E0.................
26:Fernotron ^P82#.*
27:SD_BELL ^P(?:15|32|41|42|57|79|96|98|112)#.*
28:SD_Keeloq ^P(?:87|88)#.*
29:SD_GT ^P49#[A-Fa-f0-9]+
30:LaCrosse ^(\S+\s+9 |OK\sWS\s)
31:KOPP_FC ^kr..................
32:PCA301 ^\S+\s+24
33:SD_Rojaflex ^P109#[A-Fa-f0-9]+
34:WMBUS ^b.*
35:HMS ^810e04......a001
36:IFB ^J............
37:LTECH ^P31#[A-Fa-f0-9]{26,}
90:SD_Tool ^pt([0-9]+(\.[0-9])?)(#.*)?
X:SIGNALduino_un ^\d+#.*
QUEUE:
READINGS:
2023-08-28 16:51:22 ping OK
2023-08-28 16:44:22 state opened
2023-08-28 16:49:32 version V 3.5.0 SIGNALduino - compiled at Jul 8 2022 18:09:56
getcmd:
helper:
avrdudelogs flashing Arduino Nano
hex file: FHEM/firmware/SIGNALDuino_nanocc1101_3.5.0.hex
port: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
host: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
log file: ./log/SIGNALduino-Flash.log
Nano closed
command: avrdude -c arduino -b 57600 -P /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0 -p atmega328p -vv -U flash:w:FHEM/firmware/SIGNALDuino_nanocc1101_3.5.0.hex 2>./log/SIGNALduino-Flash.log
--- AVRDUDE ---------------------------------------------------------------------------------
avrdude: Version 6.3-20171130
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2014 Joerg Wunsch
System wide configuration file is "/etc/avrdude.conf"
User configuration file is "/opt/fhem/.avrduderc"
User configuration file does not exist or is not a regular file, skipping
Using Port : /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
Using Programmer : arduino
Overriding Baud Rate : 57600
AVR Part : ATmega328P
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PC2
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
eeprom 65 20 4 0 no 1024 4 0 3600 3600 0xff 0xff
flash 65 6 128 0 yes 32768 128 256 4500 4500 0xff 0xff
lfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
efuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
lock 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00
Programmer Type : Arduino
Description : Arduino
Hardware Version: 2
Firmware Version: 1.16
Vtarget : 0.0 V
Varef : 0.0 V
Oscillator : Off
SCK period : 0.1 us
avrdude: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% 0.00s
avrdude: Device signature = 0x1e950f (probably m328p)
avrdude: NOTE: "flash" memory has been specified, an erase cycle will be performed
To disable this feature, specify the -D option.
avrdude: erasing chip
avrdude: reading input file "FHEM/firmware/SIGNALDuino_nanocc1101_3.5.0.hex"
avrdude: input file FHEM/firmware/SIGNALDuino_nanocc1101_3.5.0.hex auto detected as Intel Hex
avrdude: writing flash (24686 bytes):
Writing | ################################################## | 100% 7.13s
avrdude: 24686 bytes of flash written
avrdude: verifying flash memory against FHEM/firmware/SIGNALDuino_nanocc1101_3.5.0.hex:
avrdude: load data flash data from input file FHEM/firmware/SIGNALDuino_nanocc1101_3.5.0.hex:
avrdude: input file FHEM/firmware/SIGNALDuino_nanocc1101_3.5.0.hex auto detected as Intel Hex
avrdude: input file FHEM/firmware/SIGNALDuino_nanocc1101_3.5.0.hex contains 24686 bytes
avrdude: reading on-chip flash data:
Reading | ################################################## | 100% 5.43s
avrdude: verifying ...
avrdude: 24686 bytes of flash verified
avrdude done. Thank you.
--- AVRDUDE ---------------------------------------------------------------------------------
Nano opened
keepalive:
ok 1
retry 0
mcIdList:
10
11
12
18
43
47
52
57
58
96
119
129
212
mnIdList:
100
101
102
103
107
108
109
112
115
116
123
201
202
203
204
205
206
207
208
209
210
211
213
214
msIdList:
0
0.1
0.2
0.3
0.4
0.5
1
3
3.1
4
6
7
13
13.2
14
15
17
20
23
25
32.1
33
33.1
33.2
35
41
49
51
53
54.1
55
65
68
74.1
90
91.1
93
106
113
118.1
124.1
127.1
128.1
muIdList:
8
9
13.1
16
17.1
19
20.1
21
22
24
26
27
28
29
30
32
34
36
37
38
39
40
42
44
44.1
45
46
48
49.1
49.2
50
54
56
59
60
61
62
64
66
67
69
70
71
72
73
74
78
79
80
81
83
84
85
86
89
91
92
94
95
97
98
99
104
105
110
111
114
118
120
121
122
124
127
128
198
200
200.1
rfmodesets:
rfmode Avantek_433__B8_N9_FSK,Bresser_5in1_u_7in1__B28_N7_8220,Bresser_6in1__B20_N7_8220,DP100_WH51_WH57_433__B16_N16_17241,DP100_WH51_WH57_868__B16_N6_17241,HoneywActivL__SlowRf_FSK,KOPP_FC__B20_N4_4785,Lacrosse_mode1_WS1080_TX38__B12_N1_17241,Lacrosse_mode2__B12_N2_9579,PCA301_mode3__B32_N3_6631,Rojaflex_433__B12_N8_GFSK,SlowRF_ccFactoryReset,W136__B24_N10_4798,WH24_WH25__B20_N1_17241,WMBus_S__N11_ab_firmware_V422,WMBus_T_u_C__N12_ab_firmw_V422,WS1600_TX22_mode5__B16_N5_8842,custom
rfmodesetsTesting:
rfmodeTesting Avantek_433__B5_N9_FSK,Bresser_5in1_u_7in1__B26_N7_8220,Bresser_6in1__B18_N7_8220,DP100_WH51_WH57_433__B14_N16_17241,DP100_WH51_WH57_868__B14_N6_17241,Elero__N13_ab_firmw_V335_u_V422,Inkbird_433__B18_N14_FSK,Lacrosse_mode1_TX38__B5_N1_17241,Lacrosse_mode1_WS1080_TX38__B10_N1_17241,Lacrosse_mode2__B5_N2_9579,PCA301_mode3__B12_N3_6631,W136__B24_N10_4798,WH24_WH25__B16_N1_17241,WS1600_TX22_mode5__B5_N5_8842
Attributes:
hardware nanoCC1101
room Empfänger
updateChannelFW Ralf9
verbose 4
Ich weiß nicht , ob es jetzt richtig ist , aber den Temperatur-Sender bekomme ich nicht rein
Du kannst es auch mal mit meiner SIGNALduino_nanoCC1101_3321rc9 versuchen, wenn es damit auch nicht funktioniert, dann passt evtl was an dem nanocul nicht
set Nano flash https://github.com/Ralf9/SIGNALDuino/releases/download/3.3.2.1-rc9/SIGNALduino_nanoCC1101_3321rc9.hex
funktioniert auch nicht :-[
Was steht mit verbose 4 im log, wenn Du den Nanocul einsteckst?
Wenn das cc1101 Modul nicht erkannt wurde (evtl eine kalte Lötstelle)
2023-08-28 18:03:55.338 SIGNALduino sduinoA CONNECTED
...
2023.08.28 18:03:56.914 4: sduinoA/msg READ: Reading values from eeprom
2023.08.28 18:03:57.185 4: sduinoA/msg READ: CCInit no CC11xx found! ccVer=0 ccPartnum=0
wenn ok, dann:
2023-08-28 18:06:35.398 SIGNALduino sduinoA CONNECTED
...
2023.08.28 18:06:36.868 4: sduinoA/msg READ: Reading values from eeprom
2023.08.28 18:06:36.873 4: sduinoA/msg READ: CCInit ok. ccVer=0x14 ccPartnum=0
Im Log :
Zitat2023.08.28 19:00:06 3: Setting Nano serial parameters to 57600,8,N,1
2023.08.28 19:00:06 1: Nano/define: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0@57600
2023.08.28 19:00:06 1: Nano/init: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0@57600
2023.08.28 19:00:06 1: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0 reappeared (Nano)
2023.08.28 19:00:08 4: Nano/msg READ: �6>��Using sFIFO
2023.08.28 19:00:08 4: Nano/msg READ: Reading values from eeprom
2023.08.28 19:00:08 4: Nano/msg READ: CCInit no CC11xx found! ccVer=0 ccPartnum=0
2023.08.28 19:00:08 4: Nano/msg READ: Starting timerjob
2023.08.28 19:00:08 4: Nano/msg READ: receiver enabled
2023.08.28 19:00:09 3: Nano/init: disable receiver (XQ)
2023.08.28 19:00:09 3: Nano/init: get version, retry = 0
2023.08.28 19:00:09 4: Nano/msg READ: V 3.3.2.1-rc9 SIGNALduino - compiled at Jun 16 2019 20:18:01
2023.08.28 19:00:09 4: Nano/msg READ: regexp=V\s.*SIGNAL(duino|ESP).* cmd=version msg=V 3.3.2.1-rc9 SIGNALduino - compiled at Jun 16 2019 20:18:01
2023.08.28 19:00:09 3: Nano/init: firmwareversion without cc1101 found
2023.08.28 19:00:09 2: Nano: initialized. v3.4.16-dev_ralf_23.07.
2023.08.28 19:00:10 3: Nano/init: enable receiver (XE)
Das cc1101 Modul wird von der firmware nicht erkannt. Die Ursache war bei anderen schon oft eine Unterbrechung oder Wackelkontakt durch eine kalte Lötstelle,
Bitte poste mal ein Foto vom nanocul
Ich hoffe das etwas zu erkennen ist
Nein, da ist nicht viel zuerkennen.
Wie lang sind die Litzen zwischen cc1101 und nano?
Ca. 15 cm
Diese sind nicht angelötet , sondern zum stecken .
Wenn dieser defekt wäre , welchen bzw. wo sollte ich einen kaufen ?
Vertraue Aliexpress nicht unbedingt .
Dupont / Jumper Kabel Buchse-Buchse? Haben alle einen guten Kontakt?
Mit 15cm habe ich keine Erfahrung. Mit 10cm funktioniert es noch sehr gut.
Ja , Dupont / Jumper Kabel Buchse-Buchse.
Habe gerade durchgemessen , alle haben Kontakt .
Werde mir wohl einen neuen kaufen müssen .
Hast Du eine Empfehlung wo ich kaufen könnte ?
Danke
Nein für das cc1101 Modul habe ich keine Empfehlung. Bei Amazon gibts bei den blauen auch welche mit ungenauer Frequenz.
Der nano arbeitet mit 5V und das cc1101 Modul mit 3.3V. Ohne Levelshifter wird das cc1101 außerhalb der Spezifikation betrieben. Das kann in den meisten Fällen gutgehen, aber es kann auch Fälle geben wo das cc1101 defekt gehen kann.
Fehler gefunden , es war eine Lötstelle .
ist das jetzt in Ordnung ?
ZitatInternals:
Clients :CUL_EM:CUL_FHTTK:CUL_TCM97001:CUL_TX:CUL_WS:Dooya:FHT:FLAMINGO:FS10:FS20: :Fernotron:Hideki:IT:KOPP_FC:LaCrosse:OREGON:PCA301:RFXX10REC:Revolt:SD_AS:SD_Rojaflex: :SD_BELL:SD_GT:SD_Keeloq:SD_RSL:SD_UT:SD_WS07:SD_WS09:SD_WS:SD_WS_Maverick:SOMFY: :Siro:SIGNALduino_un:
DEF /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0@57600
DMSG W38#C7A2490AE
DevState initialized
DeviceName /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0@57600
FD 16
FUUID 64eb8200-f33f-cfd3-1175-3c32d992e3ede904
IDsNoDispatch 2,72.1,82
LASTDMSG W38#C7A2490AE
LASTDMSGID 38
MSGCNT 2
NAME Nano
NR 175
PARTIAL
RAWMSG MU;P0=23268;P1=-721;P2=750;P3=510;P4=-226;P5=259;P6=-464;P7=-954;CP=5;R=250;D=01212121343456565634343434563456565634565634565634565634565656563456345634343456512121212134345656563434343456345656563456563456563456563456565656345634563434345657212121213434565656343434345634565656345656345656345656345656565634563456343434565721212121;O;
RSSI -77
STATE opened
TIME 1693330342.7247
TYPE SIGNALduino
cc1101_available 1
eventCount 4
sendworking 0
version V 3.3.2.1-rc9 SIGNALduino cc1101 - compiled at Jun 16 2019 20:18:01
versionProtocols 1.53
versionmodul 3.5.5+20230827
DoubleMsgIDs:
MatchList:
10:SD_WS07 ^P7#[A-Fa-f0-9]{6}[AFaf][A-Fa-f0-9]{2,3}
11:SD_WS09 ^P9#F[A-Fa-f0-9]+
12:SD_WS ^W\d+x{0,1}#.*
13:RFXX10REC ^(20|29)[A-Fa-f0-9]+
14:Dooya ^P16#[A-Fa-f0-9]+
15:SOMFY ^Ys[0-9A-F]+
16:SD_WS_Maverick ^P47#[A-Fa-f0-9]+
17:SD_UT ^P(?:14|20|24|26|29|30|34|46|56|68|69|76|78|81|83|86|90|91|91.1|92|93|95|97|99|104|105|114|118|121|127|128)#.*
18:FLAMINGO ^P13\.?1?#[A-Fa-f0-9]+
19:CUL_WS ^K[A-Fa-f0-9]{5,}
1:IT ^i......
20:Revolt ^r[A-Fa-f0-9]{22}
21:FS10 ^P61#[A-F0-9]+
22:Siro ^P72#[A-Fa-f0-9]+
23:FHT ^81..(04|09|0d)..(0909a001|83098301|c409c401)..
24:FS20 ^81..(04|0c)..0101a001
25:CUL_EM ^E0.................
26:Fernotron ^P82#.*
27:SD_BELL ^P(?:15|32|41|42|57|79|96|98|112)#.*
28:SD_Keeloq ^P(?:87|88)#.*
29:SD_GT ^P49#[A-Fa-f0-9]+
2:CUL_TCM97001 ^s[A-Fa-f0-9]+
30:LaCrosse ^(\S+\s+9 |OK\sWS\s)
31:KOPP_FC ^kr\w{18,}
32:PCA301 ^\S+\s+24
33:SD_Rojaflex ^P109#[A-Fa-f0-9]+
3:SD_RSL ^P1#[A-Fa-f0-9]{8}
4:OREGON ^(3[8-9A-F]|[4-6][0-9A-F]|7[0-8]).*
5:CUL_TX ^TX..........
6:SD_AS ^P2#[A-Fa-f0-9]{7,8}
7:Hideki ^P12#75[A-F0-9]+
9:CUL_FHTTK ^T[A-F0-9]{8}
X:SIGNALduino_un ^\d+#.*
QUEUE:
READINGS:
2023-08-29 19:30:33 cc1101_config Freq: 433.920 MHz, Bandwidth: 325 kHz, rAmpl: 42 dB, sens: 8 dB, DataRate: 5.60 kBaud
2023-08-29 19:30:33 cc1101_config_ext Modulation: ASK/OOK
2023-08-29 19:30:33 cc1101_patable C3E = 00 84 00 00 00 00 00 00 => 5_dBm
2023-08-29 18:42:27 ping OK
2023-08-29 19:30:32 state opened
2023-08-28 16:49:32 version V 3.5.0 SIGNALduino - compiled at Jul 8 2022 18:09:56
additionalSets:
keepalive:
ok 0
retry 0
mcIdList:
10
11
12
18
43
47
52
57
58
96
119
129
mnIdList:
100
101
102
103
107
107.1
108
109
112
115
116
116.1
117
123
125
126
msIdList:
0
0.1
0.2
0.3
0.4
0.5
1
3
3.1
4
6
7
7.1
13
13.2
14
15
17
20
23
25
33
33.1
33.2
35
41
49
51
53
54.1
55
65
68
74.1
87
88
90
91.1
93
106
113
118.1
127.1
128.1
muIdList:
8
9
13.1
16
17.1
19
20.1
21
22
24
26
27
28
29
30
31
32
34
36
37
38
39
40
42
44
44.1
45
46
48
49.1
49.2
50
54
56
59
60
61
62
64
66
67
69
70
71
72
73
74
76
78
79
80
81
83
84
85
86
89
91
92
94
95
97
98
99
104
105
110
111
114
118
120
121
122
127
128
Attributes:
hardware nanoCC1101
room Empfänger
updateChannelFW Ralf9
verbose 4
Ja das cc101 Modul wird nun erkannt und es werden Nachrichten vom NC-3911 empfangen
z.B.
W38#C7A2490AE
Guten Morgen ,
kann mir jemand sagen was folgende Fehlermeldung zu bedeuten hat ??
Zitat2023.09.06 06:17:57 1: Nano: SD_WS_85 Parse msg 93916DE8BC8B6F458 - ERROR CRC not loaded, please install module Digest::CRC
Danke
Es fehlt das Perl Modul Digest::CRC
sudo apt-get install libdigest-crc-perl