Hallo!
Habe mir einen Aeotec ZW112 Door Window Sensor 6 zugelegt:
http://products.z-wavealliance.org/products//1615 (http://products.z-wavealliance.org/products//1615)
obwohl das Gerät die CC Security (V1) unterstützen soll
https://products.z-wavealliance.org/products/1615/classes (https://products.z-wavealliance.org/products/1615/classes)
klappt das Includiren nur ohne security:
Internals:
CFGFN
DEF xxxxxxxx 81
IODev ZWDongle_0
LASTInputDev ZWDongle_0
MSGCNT 1529
NAME ZW_Reed_Eingang_19
NR 1527
STATE closed
TYPE ZWave
ZWDongle_0_MSGCNT 1529
ZWDongle_0_RAWMSG 0004005103200100
ZWDongle_0_TIME 2019-01-11 11:53:31
ZWaveSubDevice no
cmdsPending 1
homeId cb838b79
isWakeUp 1
lastMsgSent 1547149730.02275
nodeIdHex 51
READINGS:
2019-01-06 17:43:40 CMD ZW_APPLICATION_UPDATE
2019-01-06 17:41:45 SECURITY DISABLED (SECURITY not supported by device)
2019-01-07 18:13:12 SEND_DATA failed:00
2019-01-11 11:53:31 basicSet 0
2019-01-09 14:31:43 battery 100 %
2019-01-09 14:31:43 batteryPercent 100
2019-01-09 14:31:43 batteryState ok
2019-01-06 17:42:55 configIntervalTimeOfLowBatteryChecking 86640
2019-01-06 17:42:55 configLockUnlockConfiguration Unlock
2019-01-06 17:42:55 configLowBatteryCheck Enabled
2019-01-06 17:42:56 configReportTypeToSend BasicSet
2019-01-06 17:42:56 configSetTheLowBatteryValue 20
2019-01-06 17:42:56 configValueWhenTheMagnetIsTriggered Open0xFFClose0x00
2019-01-06 17:41:48 config_9 256
2019-01-06 17:41:48 model Aeotec ZW112 Door Window Sensor 6
2019-01-06 17:41:48 modelConfig aeotec/zw112.xml
2019-01-06 17:41:48 modelId 0086-0002-0070
2019-01-09 16:11:26 neighborList ZWDongle_0 (...gekürzt!)
2019-01-10 20:49:12 neighborUpdate failed
2019-01-06 17:41:45 state wakeupInterval 86400 1
2019-01-09 14:31:45 timeToAck 0.053
2019-01-09 19:47:34 transmit NO_ACK
2019-01-06 17:43:05 version Lib 3 Prot 4.05 App 1.2 HW 112 FWCounter 0
2019-01-10 20:48:50 wakeup notification
2019-01-06 17:43:26 wakeupIntervalCapabilitiesReport min 240 max 864000 default 0 step 240
2019-01-06 17:43:19 wakeupReport interval 86400 target 1
2019-01-06 17:43:34 zwavePlusInfo version:01 role:SleepingReportingSlave node:Z-Wave+Node installerIcon:0c06 userIcon:0c06
SendStack:
sentset:485151
Attributes:
IODev ZWDongle_0
classes ZWAVEPLUS_INFO SENSOR_BINARY BATTERY WAKE_UP CONFIGURATION ASSOCIATION ASSOCIATION_GRP_INFO ALARM VERSION MANUFACTURER_SPECIFIC POWERLEVEL FIRMWARE_UPDATE_MD DEVICE_RESET_LOCALLY MARK
devStateIcon closed:fts_door@grey: open:fts_door_open@red:
stateFormat {(ReadingsVal($name,"basicSet","") == 0) ? ("closed") : ("open") }
vclasses ALARM:4 ASSOCIATION:2 ASSOCIATION_GRP_INFO:1 BATTERY:1 CONFIGURATION:1 DEVICE_RESET_LOCALLY:1 FIRMWARE_UPDATE_MD:2 MANUFACTURER_SPECIFIC:2 POWERLEVEL:1 SENSOR_BINARY:1 VERSION:2 WAKE_UP:2 ZWAVEPLUS_INFO:2
wie man sieht fehlt im Attribut "classes" auch der Eintrag "SECURITY" der auch bei, ohne Security includierten Geräten, die aber Security unterstützen würden dort aufscheint!
Woran kann das liegen?
LG
Rainer
Übrigens: gleiches gillt auch für Aeotec ZW100 MultiSensor 6:
http://products.z-wavealliance.org/products//2714 (http://products.z-wavealliance.org/products//2714)
Bei dem Gerät war mir Security nicht so wichtig, weshalb ich es damals auf sich beruhen ließ
Ich kenne das Geraet nicht, ich habe nur den Beipackzettel, was verlinkt war, angeschaut:
ZitatIncluding Door Window Sensor as a non-secure device:
If you want your Sensor as a non-security device in your Z-wave network, you just need to press the Action Button once on Door Window Sensor when you use a controller/gateway to add/include your Sensor. The green LED will be on for 2 seconds and then the orange LED will fast blink for 10 minutes (if the Sensor does not receive the Wake Up No More Info command from primary Controller) to indicate the inclusion is successful.
Including Door Window Sensor as a secure device:
In order to take full advantage of all functionality the Door Window Sensor, you may want your Sensor is a security device that uses secure/encrypted message to communicate in Z-wave network, so a security enabled controller/gateway is needed for the Door Window Sensor to be used as a security device. You need to press the Sensor's Action Button 2 times within 1 second when your security controller/gateway starts the network inclusion. The blue LED will be on for 2 seconds and then the orange LED will fast blink for 10 minutes (if the Sensor does not receive the Wake Up No More Info command from primary Controller) to indicate the inclusion is successful.
Hallo Rudolf!
Spät aber doch (hab derzeit viel um die Ohren): Danke für die Antwort!!
Hab schon geglaubt, ich wäre zu blöd den Beipackzettel richtig zu lesen, aber der meinem Gerät beigelegte, scheint eine gekürzte Version zu sein die ausgerechnet diese Information unterschlägt!
Der von hier: https://products.z-wavealliance.org/ProductManual/File?folder=&filename=Manuals/1615/Door%20Window%20Sensor%206%20manual.pdf (https://products.z-wavealliance.org/ProductManual/File?folder=&filename=Manuals/1615/Door%20Window%20Sensor%206%20manual.pdf) enthält den von dir zitierten Text.
Und das zweimalige Drücken hat (nach ein paar Versuchen) funktioniert.
Bei den meisten Geräten, die ich habe, (auch die Innensirene von Aeotec!) gibt alleine der Inclusions-Modus des Controllers vor ob sercure oder nicht includiert wird. Daher bin ich nicht auf die Idee gekommen am Gerät etwas anders zu machen, damit es auch die Security-Klasse bekannt gibt.
LG
Rainer