FHEM+Arduino Firmata via Ethernet+RF 433 Mhz Sender+Baumarkt-Funksteckdosen

Christian. · 05 November 2014, 21:36:18

Ich bekomme mit Deiner Änderung bei jedem empfangenen Code eine Warnung:

2014.11.05 21:30:53 3: receiver: Unknown IT device detected, define one to get detailed information.
Das vorgeschlagene define bringt aber leider keine Details... gefällt mir nicht...

Christian. · 05 November 2014, 21:42:39

Zitat von: blueberry63 am 05 November 2014, 20:12:03
ich funke mal schnell dazwischen: ES FUNKTIONIERT!

...mit der Sketch-Version 2.60

Na herzlichen Glückwunsch! Damit kein anderer Deine Schmerzen erleiden muss, habe ich gerade noch eine Prüfung eingebaut: wenn auf dem Arduino eine nicht unterstützte Firmata-Version läuft, bricht die Initialisierung der FRM_RC-Devices mit einer Fehlermeldung und einer Liste der unterstützten Versionen ab.

Christian. · 05 November 2014, 22:00:31

Im Anhang befindet sich die aktuelle Version, in die ich auch die Änderung von papa eingebaut habe. Ins Git-Repository, über das RCSwitchFirmata hoffentlich irgendwann in die offizielle Version von FHEM übernommen wird, werde ich diese Änderung aber nicht übernehmen, solange das offizielle IT-Modul keine Implementierung von Parse enthält.

papa · 06 November 2014, 08:36:14

Zitat von: Christian. am 05 November 2014, 21:36:18
Ich bekomme mit Deiner Änderung bei jedem empfangenen Code eine Warnung:
Code Auswählen Erweitern
2014.11.05 21:30:53 3: receiver: Unknown IT device detected, define one to get detailed information.
Das vorgeschlagene define bringt aber leider keine Details... gefällt mir nicht...

Hm - ich schicke ja einfach alles als IT Code weiter. Vielleicht muss man noch prüfen, ob es denn wirklich ein IT Code ist ?

Christian. · 06 November 2014, 13:51:16

Nein, ich habe nachgesehen: die Meldung wird von perl.pl immer ausgegeben, wenn das IT-Modul keine Parse-Funktion enthält. Und das ist genau der Unterschied zwischen der normalen under der gepatchten Version.

blueberry63 · 15 November 2014, 09:18:58

Hallo,

Zitat
Im Anhang befindet sich die aktuelle Version, in die ich auch die Änderung von papa eingebaut habe. Ins Git-Repository, über das RCSwitchFirmata hoffentlich irgendwann in die offizielle Version von FHEM übernommen wird, werde ich diese Änderung aber nicht übernehmen, solange das offizielle IT-Modul keine Implementierung von Parse enthält.

heute habe ich beim UPDATE gesehen, daß das Modul 10_IT.pm mit "parse received it messages" eingespielt worden ist. Bedeutet es, daß 20_FRM_RCIN nun entsprechend angepaßt werden kann? Und was fehlt jetzt noch, um die FRM_RC-Module in den Standard zu übernehmen? Bei mir funktioniert jedenfalls alles (FRM_RCOUT) bestens und ich bin sehr zufrieden mit dieser Lösung, da ich hiermit bei der Positionierung des 433 MHz-Funkmoduls flexibler bin, als wenn das Teil direkt am FHEM-Server angeschlossen ist. Nochmal GROSSEN DANK für die tolle Arbeit.

Gruß
Blueberry63

Gruß
Blueberry63

Christian. · 15 November 2014, 15:15:30

Danke für den Hinweis. Ich habe gerade FHEM aktualisiert und getestet; alles funktioniert wie gewünscht. Ich werde die Änderung von papa also auch ins Git-Repository hochladen, damit Norbert sie ins offizielle FHEM-Subversion-Repository übernehmen kann.

digital.arts · 20 November 2014, 13:49:28

Hallo,
@blueberry63
kannst Du bitte eine kurze Übersicht der Pinbelegung (Anschluß-Schema) posten,
wie ich einen 433er Sender und 433er Empfänger an einen Nano (mit ENC28J60 Shield) verbinde.
Wäre sehr nett von Dir; ich habe in den alten Posts (u.a. von Wzut) leider nichts konkretes dafür gefunden (jedenfalls nichts, das ich als Laie umsetzen kann

)

vg
Karl

blueberry63 · 20 November 2014, 13:53:32

@digital.arts

heute geht es nicht mehr, aber morgen Abend werde ich es hier posten.

Gruß
Blueberry63

blueberry63 · 20 November 2014, 15:21:35

@digital.arts

ich habe noch ein Foto von meinem Testaufbau gefunden. Vielleicht reicht Dir das ja schon. Allerdings verwende ich kein ENC28J60-, sondern das W5100-Shield. Der Treiber für das ENC28J60 ist für den Nano zu groß!

Gruß
Blueberry63

digital.arts · 21 November 2014, 00:02:44

Hallo Blueberry63,
Danke schon mal für das Foto, aber ein zusätzlicher Pin - Plan wäre trotzdem sehr hilfreich.
Mit dem ENC probier ich es, hab auch einen "1wire-LAN-nanoFirmata" damit am laufen...
Notfalls bestell ich mir halt noch W5100...

Vg
Karl

Wzut · 21 November 2014, 11:31:14

Zitat von: digital.arts am 21 November 2014, 00:02:44
ein zusätzlicher Pin - Plan wäre trotzdem sehr hilfreich.

Das einfache Sendemodul hat doch nur vier Pins : VCC,GND, DATA & ANT
ANT = Antenne
VCC = 5V
GND = Masse
Data = ein beliebieger freier I/O Pin des Arduinos , welchen du genommen hast legst du dann beim define in FHEM fest.

digital.arts · 21 November 2014, 12:42:34

Hallo,
@Wzut
Danke für den Hinweis; hätte ich auch selber draufkommen können, habe mir ja auch schon einen 1wire-Lan-nanoFirmata
zusammengebaut... da definiere ich ja auch den Pin, an dem meine 18B20 hängen

Dann werde ich am WE was zum basteln haben

VG
Karl

blueberry63 · 21 November 2014, 21:05:35

@Digital.arts

hier ist der versprochene PIN-Belegungsplan (s. Anhang)

Gruß
Blueberry63

digital.arts · 25 November 2014, 22:15:33

Hallo,

ich habe leider noch keinen richtigen Erfolg mit dem "RC-Firmata-Arduino" gehabt...
Was funktioniert:
- Verkabelung Nano mit 433er Sender und 433er Empfänger
- SendDemo-Sketch aus dem RCSwitch-Ordner funktioniert, d.h. schaltet eine meiner Dosen ein/aus (wie im Sketch vorgesehen...)
- ReceiveDemo_Advanced -Sketch aus dem RCSwitch-Ordner funktioniert, d.h. meine Fernbedienung wird erkannt (Werte für alle Tasten erscheinen)
Ich gehe also davon aus, dass die Hardware soweit richtig angeschlossen ist und auch funktioniert.

Was habe ich dann getan:
- RCSwitchFirmata-Sketch vom 5.11. angepasst (Ethernet deaktiviert, da noch kein W5100 vorhanden, überflüssige Module auskommentiert...)

Code Auswählen

/*
 * Firmata is a generic protocol for communicating with microcontrollers
 * from software on a host computer. It is intended to work with
 * any host computer software package.
 *
 * To download a host software package, please click on the following link
 * to open the download page in your default browser.
 *
 * http://firmata.org/wiki/Download
 */

/*
  Copyright (C) 2006-2008 Hans-Christoph Steiner.  All rights reserved.
  Copyright (C) 2010-2011 Paul Stoffregen.  All rights reserved.
  Copyright (C) 2009 Shigeru Kobayashi.  All rights reserved.
  Copyright (C) 2009-2013 Jeff Hoefs.  All rights reserved.
  Copyright (C) 2013 Norbert Truchsess. All rights reserved.
  Copyright (C) 2014 Nicolas Panel. All rights reserved.
  
  This library is free software; you can redistribute it and/or
  modify it under the terms of the GNU Lesser General Public
  License as published by the Free Software Foundation; either
  version 2.1 of the License, or (at your option) any later version.
 
  See file LICENSE.txt for further informations on licensing terms.

  formatted using the GNU C formatting and indenting
*/


#include <Firmata.h>

/* 
 * by default Firmata uses the Serial-port (over USB) of Arduino. 
 * ConfigurableFirmata may also comunicate over ethernet using tcp/ip. 
 * To configure this 'Network Firmata' to use the original WIZ5100-based
 * ethernet-shield or Arduino Ethernet uncomment the includes of 'SPI.h' and 'Ethernet.h':
 */

//#include <SPI.h>
//#include <Ethernet.h>

/*
 * To configure 'Network Firmata' to use an ENC28J60 based board include
 * 'UIPEthernet.h' (no SPI.h required). The UIPEthernet-library can be downloaded
 * from: https://github.com/ntruchsess/arduino_uip
 */

//#include <UIPEthernet.h>

#if defined ethernet_h || defined UIPETHERNET_H
/*==============================================================================
 * Network configuration for Network Firmata
 *============================================================================*/
#define NETWORK_FIRMATA
//replace with ip of server you want to connect to, comment out if using 'remote_host'
#define remote_ip IPAddress(192,168,1,35)
//replace with hostname of server you want to connect to, comment out if using 'remote_ip'
//#define remote_host "server.local"
//replace with the port that your server is listening on
#define remote_port 3040
//replace with arduinos ip-address. Comment out if Ethernet-startup should use dhcp
#define local_ip IPAddress(192,168,1,172)
//replace with ethernet shield mac. It's mandatory every device is assigned a unique mac
const byte mac[] = {0x90,0xA2,0xDA,0x0D,0x07,0x03};
#endif

// To configure, save this file to your working directory so you can edit it
// then comment out the include and declaration for any features that you do 
// not need below.

// Also note that the current compile size for an Arduino Uno with all of the
// following features enabled is about 22.4k. If you are using an older Arduino
// or other microcontroller with less memory you will not be able to include
// all of the following feature classes.

#include <utility/DigitalInputFirmata.h>
DigitalInputFirmata digitalInput;

#include <utility/DigitalOutputFirmata.h>
DigitalOutputFirmata digitalOutput;

//#include <utility/AnalogInputFirmata.h>
//AnalogInputFirmata analogInput;

//#include <utility/AnalogOutputFirmata.h>
//AnalogOutputFirmata analogOutput;

#include <Servo.h> //wouldn't load from ServoFirmata.h in Arduino1.0.3
//#include <utility/ServoFirmata.h>
//ServoFirmata servo;

#include <Wire.h> //wouldn't load from I2CFirmata.h in Arduino1.0.3
//#include <utility/I2CFirmata.h>
//I2CFirmata i2c;

//#include <utility/OneWireFirmata.h>
//OneWireFirmata oneWire;

//#include <utility/StepperFirmata.h>
//StepperFirmata stepper;

#include <RCSwitch.h> //wouldn't load from RCOutputFirmata.h in Arduino1.0.3
#include <utility/RCOutputFirmata.h>
RCOutputFirmata rcOutput;

#include <RCSwitch.h> //wouldn't load from RCInputFirmata.h in Arduino1.0.3
#include <utility/RCInputFirmata.h>
RCInputFirmata rcInput;

//#include <utility/FirmataExt.h>
//FirmataExt firmataExt;

//#include <utility/FirmataScheduler.h>
//FirmataScheduler scheduler;

//#include <utility/EncoderFirmata.h>
//EncoderFirmata encoder;


// dependencies. Do not comment out the following lines
#if defined AnalogOutputFirmata_h || defined ServoFirmata_h
#include <utility/AnalogWrite.h>
#endif

#if defined AnalogInputFirmata_h || defined I2CFirmata_h || defined EncoderFirmata_h || defined RCInputFirmata_h
#include <utility/FirmataReporting.h>
FirmataReporting reporting;
#endif

// dependencies for Network Firmata. Do not comment out.
#ifdef NETWORK_FIRMATA
#if defined remote_ip && defined remote_host
#error "cannot define both remote_ip and remote_host at the same time!"
#endif
#include <utility/EthernetClientStream.h>
EthernetClient client;
#if defined remote_ip && !defined remote_host
#ifdef local_ip
  EthernetClientStream stream(client,local_ip,remote_ip,NULL,remote_port);
#else
  EthernetClientStream stream(client,IPAddress(0,0,0,0),remote_ip,NULL,remote_port);
#endif
#endif
#if !defined remote_ip && defined remote_host
#ifdef local_ip
  EthernetClientStream stream(client,local_ip,IPAddress(0,0,0,0),remote_host,remote_port);
#else
  EthernetClientStream stream(client,IPAddress(0,0,0,0),IPAddress(0,0,0,0),remote_host,remote_port);
#endif
#endif
#endif

/*==============================================================================
 * FUNCTIONS
 *============================================================================*/

void systemResetCallback()
{
  // initialize a defalt state

  // pins with analog capability default to analog input
  // otherwise, pins default to digital output
  for (byte i=0; i < TOTAL_PINS; i++) {
    if (IS_PIN_ANALOG(i)) {
#ifdef AnalogInputFirmata_h
      // turns off pullup, configures everything
      Firmata.setPinMode(i, ANALOG);
#endif
    } else if (IS_PIN_DIGITAL(i)) {
#ifdef DigitalOutputFirmata_h
      // sets the output to 0, configures portConfigInputs
      Firmata.setPinMode(i, OUTPUT);
#endif
    }
  }

#ifdef FirmataExt_h
  firmataExt.reset();
#endif
}

/*==============================================================================
 * SETUP()
 *============================================================================*/

void setup() 
{
#ifdef NETWORK_FIRMATA
#ifdef local_ip
  Ethernet.begin((uint8_t*)mac,local_ip);  //start ethernet
#else
  Ethernet.begin((uint8_t*)mac); //start ethernet using dhcp
#endif
  delay(1000);
#endif
  Firmata.setFirmwareVersion(FIRMATA_MAJOR_VERSION, FIRMATA_MINOR_VERSION);

#if defined AnalogOutputFirmata_h || defined ServoFirmata_h
  /* analogWriteCallback is declared in AnalogWrite.h */
  Firmata.attach(ANALOG_MESSAGE, analogWriteCallback);
#endif

  #ifdef FirmataExt_h
#ifdef DigitalInputFirmata_h
  firmataExt.addFeature(digitalInput);
#endif
#ifdef DigitalOutputFirmata_h
  firmataExt.addFeature(digitalOutput);
#endif
#ifdef AnalogInputFirmata_h
  firmataExt.addFeature(analogInput);
#endif
#ifdef AnalogOutputFirmata_h
  firmataExt.addFeature(analogOutput);
#endif
#ifdef ServoFirmata_h
  firmataExt.addFeature(servo);
#endif
#ifdef I2CFirmata_h
  firmataExt.addFeature(i2c);
#endif
#ifdef OneWireFirmata_h
  firmataExt.addFeature(oneWire);
#endif
#ifdef StepperFirmata_h
  firmataExt.addFeature(stepper);
#endif
#ifdef RCOutputFirmata_h
  firmataExt.addFeature(rcOutput);
#endif
#ifdef RCInputFirmata_h
  firmataExt.addFeature(rcInput);
#endif
#ifdef FirmataReporting_h
  firmataExt.addFeature(reporting);
#endif
#ifdef FirmataScheduler_h
  firmataExt.addFeature(scheduler);
#endif
#ifdef EncoderFirmata_h
  firmataExt.addFeature(encoder);
#endif
#endif
  /* systemResetCallback is declared here (in ConfigurableFirmata.ino) */
  Firmata.attach(SYSTEM_RESET, systemResetCallback);

  // Network Firmata communicates with Ethernet-shields over SPI. Therefor all
  // SPI-pins must be set to IGNORE. Otherwise Firmata would break SPI-communication.
  // add Pin 10 and configure pin 53 as output if using a MEGA with Ethernetshield.
  // No need to ignore pin 10 on MEGA with ENC28J60, as here pin 53 should be connected to SS:
#ifdef NETWORK_FIRMATA
  // ignore SPI and pin 4 that is SS for SD-Card on Ethernet-shield
  for (byte i=0; i < TOTAL_PINS; i++) {
    if (IS_PIN_SPI(i)
        || 4==i
        // || 10==i //explicitly ignore pin 10 on MEGA as 53 is hardware-SS but Ethernet-shield uses pin 10 for SS
        ) {
      Firmata.setPinMode(i, IGNORE);
    }
  }
//  pinMode(PIN_TO_DIGITAL(53), OUTPUT); configure hardware-SS as output on MEGA
  pinMode(PIN_TO_DIGITAL(4), OUTPUT); // switch off SD-card bypassing Firmata
  digitalWrite(PIN_TO_DIGITAL(4), HIGH); // SS is active low;

  // start up Network Firmata:
  Firmata.begin(stream);
#else
  // start up the default Firmata using Serial interface:
  Firmata.begin(57600);
#endif
  systemResetCallback();  // reset to default config
}

/*==============================================================================
 * LOOP()
 *============================================================================*/
void loop() 
{
#ifdef DigitalInputFirmata_h
  /* DIGITALREAD - as fast as possible, check for changes and output them to the
   * stream buffer using Firmata.write()  */
  digitalInput.report();
#endif

  /* STREAMREAD - processing incoming messagse as soon as possible, while still
   * checking digital inputs.  */
  while(Firmata.available()) {
    Firmata.processInput();
#ifdef FirmataScheduler_h
    if (!Firmata.isParsingMessage()) {
      goto runtasks;
    }
  }
  if (!Firmata.isParsingMessage()) {
runtasks: scheduler.runTasks();
#endif
  }

  /* SEND STREAM WRITE BUFFER - TO DO: make sure that the stream buffer doesn't go over
   * 60 bytes. use a timer to sending an event character every 4 ms to
   * trigger the buffer to dump. */

#ifdef FirmataReporting_h
  if (reporting.elapsed()) {
#ifdef AnalogInputFirmata_h
    /* ANALOGREAD - do all analogReads() at the configured sampling interval */
    analogInput.report();
#endif
#ifdef I2CFirmata_h
    // report i2c data for all device with read continuous mode enabled
    i2c.report();
#endif
#ifdef EncoderFirmata_h
    // report encoders positions if reporting enabled.
    encoder.report();
#endif
#ifdef RCInputFirmata_h
    rcInput.report();
#endif
  }
#endif
#ifdef StepperFirmata_h
  stepper.update();
#endif
#if defined NETWORK_FIRMATA && !defined local_ip
  if (Ethernet.maintain())
    {
      stream.maintain(Ethernet.localIP());
    }
#endif
}

Wird ohne Fehler kompiliert und geflasht
- Module FRM_RC, FRM_RCIN, FRM_RCOUT vom 5.11. in den FHEM-Module-Ordner kopiert

Meine Definitionen:

Code Auswählen



define ARD433 FRM /dev/serial/by-id/usb-FTDI_FT232R_USB_UART_A94JRDT5-if00-port0@57600

# Empfänger an PIN D2
define EMPF433 FRM_RCIN 2
attr EMPF433 IODev ARD433

# Sender an PIN D7
define SENDER433 FRM_RCOUT 7
attr SENDER433 IODev ARD433

### Teststeckdose
define test IT 00FFF0FFFF 0F F0
attr test IODev SENDER433

Wird alles ohne Fehler angelegt, aber die Steckdose reagiert nicht auf on oder off aus FHEM heraus...
mein Log dazu:

Code Auswählen

2014.11.25 21:43:44 5: Initializing Type Library:
2014.11.25 21:43:44 1: Including fhem.cfg
2014.11.25 21:43:44 5: Cmd: >attr global userattr devStateIcon devStateStyle icon sortby webCmd widgetOverride<
2014.11.25 21:43:44 5: Cmd: >attr global autoload_undefined_devices 1<
2014.11.25 21:43:44 5: Cmd: >attr global logfile ./log/fhem-%Y-%m.log<
2014.11.25 21:43:44 5: Cmd: >attr global modpath .<
2014.11.25 21:43:44 5: Cmd: >attr global motd Error messages while initializing FHEM:
statefile: Undefined value Fa64a5a<
2014.11.25 21:43:44 5: Cmd: >attr global sendStatistics onUpdate<
2014.11.25 21:43:44 5: Cmd: >attr global statefile ./log/fhem.save<
2014.11.25 21:43:44 5: Cmd: >attr global uniqueID ./FHEM/FhemUtils/uniqueID<
2014.11.25 21:43:44 5: Cmd: >attr global updateInBackground 1<
2014.11.25 21:43:44 5: Cmd: >attr global verbose 5<
2014.11.25 21:43:44 5: Cmd: >define telnetPort telnet 7072 global<
2014.11.25 21:43:44 5: Loading ./FHEM/98_telnet.pm
2014.11.25 21:43:44 3: telnetPort: port 7072 opened
2014.11.25 21:43:44 5: Cmd: >define WEB FHEMWEB 8083 global<
2014.11.25 21:43:44 5: Loading ./FHEM/01_FHEMWEB.pm
2014.11.25 21:43:45 3: WEB: port 8083 opened
2014.11.25 21:43:45 5: Cmd: >attr WEB basicAuth xxx<
2014.11.25 21:43:45 5: Cmd: >define WEBphone FHEMWEB 8084 global<
2014.11.25 21:43:45 3: WEBphone: port 8084 opened
2014.11.25 21:43:45 5: Cmd: >attr WEBphone basicAuth xxx<
2014.11.25 21:43:45 5: Cmd: >attr WEBphone stylesheetPrefix smallscreen<
2014.11.25 21:43:45 5: Cmd: >define WEBtablet FHEMWEB 8085 global<
2014.11.25 21:43:45 3: WEBtablet: port 8085 opened
2014.11.25 21:43:45 5: Cmd: >attr WEBtablet basicAuth xxx<
2014.11.25 21:43:45 5: Cmd: >attr WEBtablet stylesheetPrefix touchpadattr<
2014.11.25 21:43:45 5: Cmd: >define Logfile FileLog ./log/fhem-%Y-%m.log fakelog<
2014.11.25 21:43:45 5: Loading ./FHEM/92_FileLog.pm
2014.11.25 21:43:45 5: Cmd: >define autocreate autocreate<
2014.11.25 21:43:45 5: Loading ./FHEM/98_autocreate.pm
2014.11.25 21:43:45 5: Cmd: >attr autocreate ignoreTypes KW9010|Lifetec|AURIOL<
2014.11.25 21:43:45 5: Cmd: >define eventTypes eventTypes ./log/eventTypes.txt<
2014.11.25 21:43:45 5: Loading ./FHEM/91_eventTypes.pm
2014.11.25 21:43:45 2: eventTypes: loaded 128 events from ./log/eventTypes.txt
2014.11.25 21:43:45 5: Cmd: >define ARD433 FRM /dev/serial/by-id/usb-FTDI_FT232R_USB_UART_A94JRDT5-if00-port0@57600<
2014.11.25 21:43:45 5: Loading ./FHEM/10_FRM.pm
2014.11.25 21:43:46 5: Cmd: >define EMPF433 FRM_RCIN 2<
2014.11.25 21:43:46 5: Loading ./FHEM/20_FRM_RCIN.pm
2014.11.25 21:43:46 5: Loading ./FHEM/15_FRM_RC.pm
2014.11.25 21:43:46 5: EMPF433: FRM_RC_Define
2014.11.25 21:43:46 5: Cmd: >attr EMPF433 IODev ARD433<
2014.11.25 21:43:46 4: EMPF433: IODev := ARD433
2014.11.25 21:43:46 4: EMPF433: IODev is not applied during init
2014.11.25 21:43:46 5: Cmd: >define SENDER433 FRM_RCOUT 7<
2014.11.25 21:43:46 5: Loading ./FHEM/20_FRM_RCOUT.pm
2014.11.25 21:43:46 5: SENDER433: FRM_RC_Define
2014.11.25 21:43:46 5: Cmd: >attr SENDER433 IODev ARD433<
2014.11.25 21:43:46 4: SENDER433: IODev := ARD433
2014.11.25 21:43:46 4: SENDER433: IODev is not applied during init
2014.11.25 21:43:46 5: Cmd: >define test IT 00FFF0FFFF 0F F0<
2014.11.25 21:43:46 5: Loading ./FHEM/10_IT.pm
2014.11.25 21:43:46 5: Cmd: >attr test IODev SENDER433<
2014.11.25 21:43:46 1: Including ./log/fhem.save
2014.11.25 21:43:46 5: Cmd: >setstate EMPF433 2014-11-25 21:41:25 state Initialized<
2014.11.25 21:43:46 5: Cmd: >setstate Logfile active<
2014.11.25 21:43:46 5: Cmd: >setstate SENDER433 2014-11-25 21:41:25 state Initialized<
2014.11.25 21:43:46 5: Cmd: >setstate autocreate active<
2014.11.25 21:43:46 5: Cmd: >setstate eventTypes active<
2014.11.25 21:43:46 5: Cmd: >setstate global <no definition><
2014.11.25 21:43:46 5: Cmd: >setstate test off<
2014.11.25 21:43:46 5: Cmd: >setstate test 2014-11-25 21:41:58 state off<
2014.11.25 21:43:46 5: Triggering global (1 changes)
2014.11.25 21:43:46 5: Notify loop for global INITIALIZED
2014.11.25 21:43:46 3: Opening ARD433 device /dev/serial/by-id/usb-FTDI_FT232R_USB_UART_A94JRDT5-if00-port0
2014.11.25 21:43:46 3: Setting ARD433 baudrate to 57600
2014.11.25 21:43:46 3: ARD433 device opened
2014.11.25 21:43:46 5: FRM:>ff
2014.11.25 21:43:46 5: SW: ff
2014.11.25 21:43:49 3: querying Firmata Firmware Version
2014.11.25 21:43:49 5: FRM:>f079f7
2014.11.25 21:43:49 5: SW: f079f7
2014.11.25 21:43:50 3: querying Firmata Firmware Version
2014.11.25 21:43:50 5: FRM:>f079f7
2014.11.25 21:43:50 5: SW: f079f7
2014.11.25 21:43:50 5: FRM:<f90206f079020652004300530077006900740063006800
2014.11.25 21:43:50 5: FRM:<4600690072006d0061007400610032002e0069006e006f00f7f0790206520043005300770069007400630068004600690072006d0061007400610032002e0069006e006f00f7f07902065200430053007700690074006300
2014.11.25 21:43:50 3: Firmata Firmware Version: RCSwitchFirmata2.ino V_2_06
2014.11.25 21:43:50 5: FRM:>f069f7
2014.11.25 21:43:50 5: SW: f069f7
2014.11.25 21:43:50 5: FRM:>f06bf7
2014.11.25 21:43:50 5: SW: f06bf7
2014.11.25 21:43:50 5: FRM:<68004600690072006d0061007400610032002e0069006e006f00f7
2014.11.25 21:43:51 5: FRM:>f07a6807f7
2014.11.25 21:43:51 5: SW: f07a6807f7
2014.11.25 21:43:51 5: FRM:>f4020b
2014.11.25 21:43:51 5: SW: f4020b
2014.11.25 21:43:51 4: EMPF433: Registering new sysex observer
2014.11.25 21:43:51 5: Triggering EMPF433 (1 changes)
2014.11.25 21:43:51 5: Notify loop for EMPF433 Initialized
2014.11.25 21:43:51 4: eventTypes: FRM_RCIN EMPF433 Initialized -> Initialized
2014.11.25 21:43:51 4: eventTypes: FRM_RCIN EMPF433 state: Initialized -> state: Initialized
2014.11.25 21:43:51 5: FRM:>f4070a
2014.11.25 21:43:51 5: SW: f4070a
2014.11.25 21:43:51 4: SENDER433: Reusing existing sysex observer CODE(0x2218a48)
2014.11.25 21:43:51 5: Triggering SENDER433 (1 changes)
2014.11.25 21:43:51 5: Notify loop for SENDER433 Initialized
2014.11.25 21:43:51 4: eventTypes: FRM_RCOUT SENDER433 Initialized -> Initialized
2014.11.25 21:43:51 4: eventTypes: FRM_RCOUT SENDER433 state: Initialized -> state: Initialized
2014.11.25 21:43:51 5: EMPF433: FRM_RC_Notify: INITIALIZED
2014.11.25 21:43:51 4: EMPF433: IODev is already configured
2014.11.25 21:43:51 5: EMPF433: gndPin is undefined
2014.11.25 21:43:51 5: EMPF433: vccPin is undefined
2014.11.25 21:43:51 5: EMPF433: tolerance is undefined
2014.11.25 21:43:51 5: EMPF433: rawData is undefined
2014.11.25 21:43:51 5: SENDER433: FRM_RC_Notify: INITIALIZED
2014.11.25 21:43:51 4: SENDER433: IODev is already configured
2014.11.25 21:43:51 5: SENDER433: gndPin is undefined
2014.11.25 21:43:51 5: SENDER433: vccPin is undefined
2014.11.25 21:43:51 5: SENDER433: protocol is undefined
2014.11.25 21:43:51 5: SENDER433: repeatTransmit is undefined
2014.11.25 21:43:51 5: SENDER433: pulseLength is undefined
2014.11.25 21:43:51 2: SecurityCheck:  telnetPort has no password/globalpassword attribute.  Restart FHEM for a new check if the problem is fixed, or set the global attribute motd to none to supress this message. 
2014.11.25 21:43:51 0: Server started with 12 defined entities (version $Id: fhem.pl 6913 2014-11-08 10:32:44Z rudolfkoenig $, os linux, user root, pid 2364)
2014.11.25 21:43:51 4: Connection accepted from FHEMWEB:192.168.1.36:49814
2014.11.25 21:43:51 4: Connection accepted from FHEMWEB:192.168.1.36:49815
2014.11.25 21:43:52 4: HTTP FHEMWEB:192.168.1.36:49814 GET /fhem/FileLog_logWrapper?XHR=1&inform=type=status;filter=&timestamp=1416948225695
2014.11.25 21:43:52 4: Connection closed for FHEMWEB:192.168.1.36:49815
2014.11.25 21:43:52 4: Connection closed for FHEMWEB:192.168.1.36:49814
2014.11.25 21:43:52 4: Connection accepted from FHEMWEB:192.168.1.36:49816
2014.11.25 21:43:52 4: HTTP FHEMWEB:192.168.1.36:49816 GET /fhem?room=all
2014.11.25 21:43:52 4: /fhem?room=all / RL:1523 / text/html; charset=UTF-8 / Content-Encoding: gzip
 / 
2014.11.25 21:43:52 4: HTTP FHEMWEB:192.168.1.36:49816 GET /fhem/pgm2/style.css
2014.11.25 21:43:52 4: HTTP FHEMWEB:192.168.1.36:49816 GET /fhem/pgm2/fhemweb_slider.js
2014.11.25 21:43:52 4: Connection accepted from FHEMWEB:192.168.1.36:49817
2014.11.25 21:43:52 4: HTTP FHEMWEB:192.168.1.36:49816 GET /fhem/pgm2/fhemweb_svg.js
2014.11.25 21:43:52 4: HTTP FHEMWEB:192.168.1.36:49817 GET /fhem/pgm2/svg.js
2014.11.25 21:43:52 4: Connection accepted from FHEMWEB:192.168.1.36:49818
2014.11.25 21:43:52 4: HTTP FHEMWEB:192.168.1.36:49816 GET /fhem/pgm2/fhemweb_textField.js
2014.11.25 21:43:52 4: HTTP FHEMWEB:192.168.1.36:49818 GET /fhem/pgm2/fhemweb_colorpicker.js
2014.11.25 21:43:52 4: Connection accepted from FHEMWEB:192.168.1.36:49819
2014.11.25 21:43:52 4: HTTP FHEMWEB:192.168.1.36:49817 GET /fhem/pgm2/defaultCommon.css
2014.11.25 21:43:52 4: HTTP FHEMWEB:192.168.1.36:49816 GET /fhem/icons/favicon
2014.11.25 21:43:52 4: HTTP FHEMWEB:192.168.1.36:49819 GET /fhem/pgm2/fhemweb_multiple.js
2014.11.25 21:43:52 4: Connection accepted from FHEMWEB:192.168.1.36:49820
2014.11.25 21:43:52 4: HTTP FHEMWEB:192.168.1.36:49818 GET /fhem/pgm2/dashboard_style.css
2014.11.25 21:43:52 4: Connection accepted from FHEMWEB:192.168.1.36:49821
2014.11.25 21:43:52 4: HTTP FHEMWEB:192.168.1.36:49820 GET /fhem/pgm2/fhemweb_noArg.js
2014.11.25 21:43:53 4: HTTP FHEMWEB:192.168.1.36:49821 GET /fhem/pgm2/fhemweb_readingsHistory.js
2014.11.25 21:43:53 4: HTTP FHEMWEB:192.168.1.36:49816 GET /fhem/images/default/icoEverything.png
2014.11.25 21:43:53 4: HTTP FHEMWEB:192.168.1.36:49817 GET /fhem/images/default/off.png
2014.11.25 21:43:53 4: HTTP FHEMWEB:192.168.1.36:49816 GET /fhem/images/default/fhemicon.png
2014.11.25 21:43:53 4: HTTP FHEMWEB:192.168.1.36:49816 GET /fhem?XHR=1&inform=type=status;filter=room=all&timestamp=1416948234650
2014.11.25 21:44:00 4: HTTP FHEMWEB:192.168.1.36:49819 GET /fhem?XHR=1&cmd.test=set%20test%20on&room=all
2014.11.25 21:44:00 5: Cmd: >set test on<
2014.11.25 21:44:00 2: IT set test on
2014.11.25 21:44:00 4: SENDER433: Sending 0 40 7 5 69 81
2014.11.25 21:44:00 5: FRM:>f0002807050a4502f7
2014.11.25 21:44:00 5: SW: f0002807050a4502f7
2014.11.25 21:44:00 4: Answer from SENDER433: raw => is00FFF0FFFF0F
2014.11.25 21:44:00 5: Triggering test (1 changes)
2014.11.25 21:44:00 5: Notify loop for test on
2014.11.25 21:44:00 4: eventTypes: IT test on -> on
2014.11.25 21:44:00 4: /fhem?XHR=1&cmd.test=set%20test%20on&room=all / RL:20 / text/plain; charset=UTF-8 / Content-Encoding: gzip
 / 
2014.11.25 21:44:00 4: HTTP FHEMWEB:192.168.1.36:49819 GET /fhem/images/default/on.png
2014.11.25 21:44:02 4: HTTP FHEMWEB:192.168.1.36:49819 GET /fhem?XHR=1&cmd.test=set%20test%20off&room=all
2014.11.25 21:44:02 5: Cmd: >set test off<
2014.11.25 21:44:02 2: IT set test off
2014.11.25 21:44:02 4: SENDER433: Sending 0 40 7 5 69 84
2014.11.25 21:44:02 5: FRM:>f0002807050a5102f7
2014.11.25 21:44:02 5: SW: f0002807050a5102f7
2014.11.25 21:44:02 4: Answer from SENDER433: raw => is00FFF0FFFFF0
2014.11.25 21:44:02 5: Triggering test (1 changes)
2014.11.25 21:44:02 5: Notify loop for test off
2014.11.25 21:44:02 4: eventTypes: IT test off -> off
2014.11.25 21:44:02 4: /fhem?XHR=1&cmd.test=set%20test%20off&room=all / RL:20 / text/plain; charset=UTF-8 / Content-Encoding: gzip
 / 
2014.11.25 21:44:04 4: HTTP FHEMWEB:192.168.1.36:49819 GET /fhem?XHR=1&cmd.test=set%20test%20on&room=all
2014.11.25 21:44:04 5: Cmd: >set test on<
2014.11.25 21:44:04 2: IT set test on
2014.11.25 21:44:04 4: SENDER433: Sending 0 40 7 5 69 81
2014.11.25 21:44:04 5: FRM:>f0002807050a4502f7
2014.11.25 21:44:04 5: SW: f0002807050a4502f7
2014.11.25 21:44:04 4: Answer from SENDER433: raw => is00FFF0FFFF0F
2014.11.25 21:44:04 5: Triggering test (1 changes)
2014.11.25 21:44:04 5: Notify loop for test on
2014.11.25 21:44:04 4: eventTypes: IT test on -> on
2014.11.25 21:44:04 4: /fhem?XHR=1&cmd.test=set%20test%20on&room=all / RL:20 / text/plain; charset=UTF-8 / Content-Encoding: gzip
 / 
2014.11.25 21:44:05 4: HTTP FHEMWEB:192.168.1.36:49819 GET /fhem?XHR=1&cmd.test=set%20test%20off&room=all
2014.11.25 21:44:05 5: Cmd: >set test off<
2014.11.25 21:44:05 2: IT set test off
2014.11.25 21:44:05 4: SENDER433: Sending 0 40 7 5 69 84
2014.11.25 21:44:05 5: FRM:>f0002807050a5102f7
2014.11.25 21:44:05 5: SW: f0002807050a5102f7
2014.11.25 21:44:05 4: Answer from SENDER433: raw => is00FFF0FFFFF0
2014.11.25 21:44:05 5: Triggering test (1 changes)
2014.11.25 21:44:05 5: Notify loop for test off
2014.11.25 21:44:05 4: eventTypes: IT test off -> off
2014.11.25 21:44:05 4: /fhem?XHR=1&cmd.test=set%20test%20off&room=all / RL:20 / text/plain; charset=UTF-8 / Content-Encoding: gzip
 / 
2014.11.25 21:44:23 4: Connection accepted from telnet:127.0.0.1:52374
2014.11.25 21:44:23 5: Cmd: >shutdown<
2014.11.25 21:44:23 5: Triggering global (1 changes)
2014.11.25 21:44:23 5: Notify loop for global SHUTDOWN
2014.11.25 21:44:23 5: EMPF433: FRM_RC_Notify: SHUTDOWN
2014.11.25 21:44:23 5: SENDER433: FRM_RC_Notify: SHUTDOWN
2014.11.25 21:44:23 0: Server shutdown
2014.11.25 21:45:21 5: Initializing Type Library:
2014.11.25 21:45:21 1: Including fhem.cfg
2014.11.25 21:45:21 5: Cmd: >attr global userattr devStateIcon devStateStyle icon sortby webCmd widgetOverride<
2014.11.25 21:45:21 5: Cmd: >attr global autoload_undefined_devices 1<
2014.11.25 21:45:21 5: Cmd: >attr global logfile ./log/fhem-%Y-%m.log<
2014.11.25 21:45:21 5: Cmd: >attr global modpath .<
2014.11.25 21:45:21 5: Cmd: >attr global motd Error messages while initializing FHEM:
statefile: Undefined value Fa64a5a<
2014.11.25 21:45:21 5: Cmd: >attr global sendStatistics onUpdate<
2014.11.25 21:45:21 5: Cmd: >attr global statefile ./log/fhem.save<
2014.11.25 21:45:21 5: Cmd: >attr global uniqueID ./FHEM/FhemUtils/uniqueID<
2014.11.25 21:45:21 5: Cmd: >attr global updateInBackground 1<
2014.11.25 21:45:21 5: Cmd: >attr global verbose 5<
2014.11.25 21:45:21 5: Cmd: >define telnetPort telnet 7072 global<
2014.11.25 21:45:21 5: Loading ./FHEM/98_telnet.pm
2014.11.25 21:45:21 3: telnetPort: port 7072 opened
2014.11.25 21:45:21 5: Cmd: >define WEB FHEMWEB 8083 global<
2014.11.25 21:45:21 5: Loading ./FHEM/01_FHEMWEB.pm
2014.11.25 21:45:22 3: WEB: port 8083 opened
2014.11.25 21:45:22 5: Cmd: >attr WEB basicAuth xxx<
2014.11.25 21:45:22 5: Cmd: >define WEBphone FHEMWEB 8084 global<
2014.11.25 21:45:22 3: WEBphone: port 8084 opened
2014.11.25 21:45:22 5: Cmd: >attr WEBphone basicAuth xxx<
2014.11.25 21:45:22 5: Cmd: >attr WEBphone stylesheetPrefix smallscreen<
2014.11.25 21:45:22 5: Cmd: >define WEBtablet FHEMWEB 8085 global<
2014.11.25 21:45:22 3: WEBtablet: port 8085 opened
2014.11.25 21:45:22 5: Cmd: >attr WEBtablet basicAuth xxx=<
2014.11.25 21:45:22 5: Cmd: >attr WEBtablet stylesheetPrefix touchpadattr<
2014.11.25 21:45:22 5: Cmd: >define Logfile FileLog ./log/fhem-%Y-%m.log fakelog<
2014.11.25 21:45:22 5: Loading ./FHEM/92_FileLog.pm
2014.11.25 21:45:22 5: Cmd: >define autocreate autocreate<
2014.11.25 21:45:22 5: Loading ./FHEM/98_autocreate.pm
2014.11.25 21:45:22 5: Cmd: >attr autocreate ignoreTypes KW9010|Lifetec|AURIOL<
2014.11.25 21:45:22 5: Cmd: >define eventTypes eventTypes ./log/eventTypes.txt<
2014.11.25 21:45:22 5: Loading ./FHEM/91_eventTypes.pm
2014.11.25 21:45:22 2: eventTypes: loaded 128 events from ./log/eventTypes.txt
2014.11.25 21:45:22 5: Cmd: >define ARD433 FRM /dev/serial/by-id/usb-FTDI_FT232R_USB_UART_A94JRDT5-if00-port0@57600<
2014.11.25 21:45:22 5: Loading ./FHEM/10_FRM.pm
2014.11.25 21:45:23 5: Cmd: >define EMPF433 FRM_RCIN 2<
2014.11.25 21:45:23 5: Loading ./FHEM/20_FRM_RCIN.pm
2014.11.25 21:45:23 5: Loading ./FHEM/15_FRM_RC.pm
2014.11.25 21:45:23 5: EMPF433: FRM_RC_Define
2014.11.25 21:45:23 5: Cmd: >attr EMPF433 IODev ARD433<
2014.11.25 21:45:23 4: EMPF433: IODev := ARD433
2014.11.25 21:45:23 4: EMPF433: IODev is not applied during init
2014.11.25 21:45:23 5: Cmd: >define SENDER433 FRM_RCOUT 7<
2014.11.25 21:45:23 5: Loading ./FHEM/20_FRM_RCOUT.pm
2014.11.25 21:45:23 5: SENDER433: FRM_RC_Define
2014.11.25 21:45:23 5: Cmd: >attr SENDER433 IODev ARD433<
2014.11.25 21:45:23 4: SENDER433: IODev := ARD433
2014.11.25 21:45:23 4: SENDER433: IODev is not applied during init
2014.11.25 21:45:23 5: Cmd: >define test IT 00FFF0FFFF 0F F0<
2014.11.25 21:45:23 5: Loading ./FHEM/10_IT.pm
2014.11.25 21:45:23 5: Cmd: >attr test IODev SENDER433<
2014.11.25 21:45:23 1: Including ./log/fhem.save
2014.11.25 21:45:23 5: Cmd: >setstate EMPF433 2014-11-25 21:43:51 state Initialized<
2014.11.25 21:45:23 5: Cmd: >setstate Logfile active<
2014.11.25 21:45:23 5: Cmd: >setstate SENDER433 2014-11-25 21:43:51 state Initialized<
2014.11.25 21:45:23 5: Cmd: >setstate autocreate active<
2014.11.25 21:45:23 5: Cmd: >setstate eventTypes active<
2014.11.25 21:45:23 5: Cmd: >setstate global <no definition><
2014.11.25 21:45:23 5: Cmd: >setstate test off<
2014.11.25 21:45:23 5: Cmd: >setstate test 2014-11-25 21:44:05 state off<
2014.11.25 21:45:23 5: Triggering global (1 changes)
2014.11.25 21:45:23 5: Notify loop for global INITIALIZED
2014.11.25 21:45:23 3: Opening ARD433 device /dev/serial/by-id/usb-FTDI_FT232R_USB_UART_A94JRDT5-if00-port0
2014.11.25 21:45:23 3: Setting ARD433 baudrate to 57600
2014.11.25 21:45:23 3: ARD433 device opened
2014.11.25 21:45:23 5: FRM:>ff
2014.11.25 21:45:23 5: SW: ff
2014.11.25 21:45:26 3: querying Firmata Firmware Version
2014.11.25 21:45:26 5: FRM:>f079f7
2014.11.25 21:45:26 5: SW: f079f7
2014.11.25 21:45:27 3: querying Firmata Firmware Version
2014.11.25 21:45:27 5: FRM:>f079f7
2014.11.25 21:45:27 5: SW: f079f7
2014.11.25 21:45:27 5: FRM:<f902
2014.11.25 21:45:27 5: FRM:<06f0790206520043005300770069007400630068004600690072006d0061007400610032002e0069006e006f00f7f0790206520043005300770069007400630068004600690072
2014.11.25 21:45:27 3: Firmata Firmware Version: RCSwitchFirmata2.ino V_2_06
2014.11.25 21:45:27 5: FRM:>f069f7
2014.11.25 21:45:27 5: SW: f069f7
2014.11.25 21:45:27 5: FRM:>f06bf7
2014.11.25 21:45:27 5: SW: f06bf7
2014.11.25 21:45:27 5: FRM:<006d0061007400610032002e0069006e006f00f7f0790206520043005300770069007400630068004600690072006d0061007400610032002e0069006e006f00f7
2014.11.25 21:45:28 5: FRM:>f07a6807f7
2014.11.25 21:45:28 5: SW: f07a6807f7
2014.11.25 21:45:28 5: FRM:>f4020b
2014.11.25 21:45:28 5: SW: f4020b
2014.11.25 21:45:28 4: EMPF433: Registering new sysex observer
2014.11.25 21:45:28 5: Triggering EMPF433 (1 changes)
2014.11.25 21:45:28 5: Notify loop for EMPF433 Initialized
2014.11.25 21:45:28 4: eventTypes: FRM_RCIN EMPF433 Initialized -> Initialized
2014.11.25 21:45:28 4: eventTypes: FRM_RCIN EMPF433 state: Initialized -> state: Initialized
2014.11.25 21:45:28 5: FRM:>f4070a
2014.11.25 21:45:28 5: SW: f4070a
2014.11.25 21:45:28 4: SENDER433: Reusing existing sysex observer CODE(0x1d67a48)
2014.11.25 21:45:28 5: Triggering SENDER433 (1 changes)
2014.11.25 21:45:28 5: Notify loop for SENDER433 Initialized
2014.11.25 21:45:28 4: eventTypes: FRM_RCOUT SENDER433 Initialized -> Initialized
2014.11.25 21:45:28 4: eventTypes: FRM_RCOUT SENDER433 state: Initialized -> state: Initialized
2014.11.25 21:45:28 5: EMPF433: FRM_RC_Notify: INITIALIZED
2014.11.25 21:45:28 4: EMPF433: IODev is already configured
2014.11.25 21:45:28 5: EMPF433: gndPin is undefined
2014.11.25 21:45:28 5: EMPF433: vccPin is undefined
2014.11.25 21:45:28 5: EMPF433: tolerance is undefined
2014.11.25 21:45:28 5: EMPF433: rawData is undefined
2014.11.25 21:45:28 5: SENDER433: FRM_RC_Notify: INITIALIZED
2014.11.25 21:45:28 4: SENDER433: IODev is already configured
2014.11.25 21:45:28 5: SENDER433: gndPin is undefined
2014.11.25 21:45:28 5: SENDER433: vccPin is undefined
2014.11.25 21:45:28 5: SENDER433: protocol is undefined
2014.11.25 21:45:28 5: SENDER433: repeatTransmit is undefined
2014.11.25 21:45:28 5: SENDER433: pulseLength is undefined
2014.11.25 21:45:28 2: SecurityCheck:  telnetPort has no password/globalpassword attribute.  Restart FHEM for a new check if the problem is fixed, or set the global attribute motd to none to supress this message. 
2014.11.25 21:45:28 0: Server started with 12 defined entities (version $Id: fhem.pl 6913 2014-11-08 10:32:44Z rudolfkoenig $, os linux, user root, pid 2371)
2014.11.25 21:45:28 4: Connection accepted from FHEMWEB:192.168.1.36:49862
2014.11.25 21:45:28 4: Connection accepted from FHEMWEB:192.168.1.36:49863
2014.11.25 21:45:29 4: HTTP FHEMWEB:192.168.1.36:49862 GET /fhem?room=all
2014.11.25 21:45:29 4: /fhem?room=all / RL:1539 / text/html; charset=UTF-8 / Content-Encoding: gzip
 / 
2014.11.25 21:45:29 4: HTTP FHEMWEB:192.168.1.36:49863 GET /fhem?XHR=1&inform=type=status;filter=room=all&timestamp=1416948326841
2014.11.25 21:45:29 4: HTTP FHEMWEB:192.168.1.36:49862 GET /fhem/pgm2/style.css
2014.11.25 21:45:29 4: Connection accepted from FHEMWEB:192.168.1.36:49864
2014.11.25 21:45:29 4: HTTP FHEMWEB:192.168.1.36:49862 GET /fhem/pgm2/fhemweb_noArg.js
2014.11.25 21:45:29 4: Connection accepted from FHEMWEB:192.168.1.36:49865
2014.11.25 21:45:29 4: HTTP FHEMWEB:192.168.1.36:49862 GET /fhem/pgm2/fhemweb_readingsHistory.js
2014.11.25 21:45:29 4: HTTP FHEMWEB:192.168.1.36:49864 GET /fhem/pgm2/svg.js
2014.11.25 21:45:29 4: Connection accepted from FHEMWEB:192.168.1.36:49866
2014.11.25 21:45:29 4: HTTP FHEMWEB:192.168.1.36:49862 GET /fhem/pgm2/fhemweb_slider.js
2014.11.25 21:45:29 4: HTTP FHEMWEB:192.168.1.36:49864 GET /fhem/pgm2/fhemweb_svg.js
2014.11.25 21:45:29 4: HTTP FHEMWEB:192.168.1.36:49865 GET /fhem/pgm2/fhemweb.js
2014.11.25 21:45:29 4: Connection accepted from FHEMWEB:192.168.1.36:49867
2014.11.25 21:45:29 4: HTTP FHEMWEB:192.168.1.36:49866 GET /fhem/pgm2/fhemweb_colorpicker.js
2014.11.25 21:45:29 4: HTTP FHEMWEB:192.168.1.36:49862 GET /fhem/pgm2/fhemweb_textField.js
2014.11.25 21:45:29 4: HTTP FHEMWEB:192.168.1.36:49864 GET /fhem/pgm2/fhemweb_time.js
2014.11.25 21:45:29 4: HTTP FHEMWEB:192.168.1.36:49865 GET /fhem/pgm2/defaultCommon.css
2014.11.25 21:45:29 4: HTTP FHEMWEB:192.168.1.36:49867 GET /fhem/pgm2/fhemweb_multiple.js
2014.11.25 21:45:29 4: HTTP FHEMWEB:192.168.1.36:49866 GET /fhem/icons/favicon
2014.11.25 21:45:29 4: HTTP FHEMWEB:192.168.1.36:49862 GET /fhem/pgm2/dashboard_style.css
2014.11.25 21:45:29 4: HTTP FHEMWEB:192.168.1.36:49862 GET /fhem/images/default/icoEverything.png
2014.11.25 21:45:29 4: HTTP FHEMWEB:192.168.1.36:49864 GET /fhem/images/default/off.png
2014.11.25 21:45:29 4: HTTP FHEMWEB:192.168.1.36:49862 GET /fhem/images/default/fhemicon.png
2014.11.25 21:45:29 4: HTTP FHEMWEB:192.168.1.36:49862 GET /fhem?XHR=1&inform=type=status;filter=room=all&timestamp=1416948331166
2014.11.25 21:45:34 4: HTTP FHEMWEB:192.168.1.36:49865 GET /fhem?XHR=1&cmd.test=set%20test%20on&room=all
2014.11.25 21:45:34 5: Cmd: >set test on<
2014.11.25 21:45:34 2: IT set test on
2014.11.25 21:45:34 4: SENDER433: Sending 0 40 7 5 69 81
2014.11.25 21:45:34 5: FRM:>f0002807050a4502f7
2014.11.25 21:45:34 5: SW: f0002807050a4502f7
2014.11.25 21:45:34 4: Answer from SENDER433: raw => is00FFF0FFFF0F
2014.11.25 21:45:34 5: Triggering test (1 changes)
2014.11.25 21:45:34 5: Notify loop for test on
2014.11.25 21:45:34 4: eventTypes: IT test on -> on
2014.11.25 21:45:34 4: /fhem?XHR=1&cmd.test=set%20test%20on&room=all / RL:20 / text/plain; charset=UTF-8 / Content-Encoding: gzip
 / 
2014.11.25 21:45:34 4: HTTP FHEMWEB:192.168.1.36:49865 GET /fhem/images/default/on.png
2014.11.25 21:45:35 4: HTTP FHEMWEB:192.168.1.36:49865 GET /fhem?XHR=1&cmd.test=set%20test%20off&room=all
2014.11.25 21:45:35 5: Cmd: >set test off<
2014.11.25 21:45:35 2: IT set test off
2014.11.25 21:45:35 4: SENDER433: Sending 0 40 7 5 69 84
2014.11.25 21:45:35 5: FRM:>f0002807050a5102f7
2014.11.25 21:45:35 5: SW: f0002807050a5102f7
2014.11.25 21:45:35 4: Answer from SENDER433: raw => is00FFF0FFFFF0
2014.11.25 21:45:35 5: Triggering test (1 changes)
2014.11.25 21:45:35 5: Notify loop for test off
2014.11.25 21:45:35 4: eventTypes: IT test off -> off
2014.11.25 21:45:35 4: /fhem?XHR=1&cmd.test=set%20test%20off&room=all / RL:20 / text/plain; charset=UTF-8 / Content-Encoding: gzip
 / 
2014.11.25 21:45:37 4: Connection closed for FHEMWEB:192.168.1.36:49863
2014.11.25 21:45:37 4: Connection closed for FHEMWEB:192.168.1.36:49862

Was habe ich übersehen, oder was ist falsch ??

Für Hilfe oder Tips wäre ich sehr dankbar

VG
Karl