SIGNALDuino Empfänger Firmware V 3.3.2r-dev

Begonnen von Ralf9, 07 Januar 2018, 21:37:44

Vorheriges Thema - Nächstes Thema

Ralf9

ccreg write back 10B03F15C4

Die eingestellte Frequenz passt nicht ganz genau, bitte mach mal ein Factoryreset

set sduino raw e

Gruß Ralf
FHEM auf Cubietruck mit Igor-Image, SSD und  hmland + HM-CFG-USB-2,  HMUARTLGW Lan,   HM-LC-Bl1PBU-FM, HM-CC-RT-DN, HM-SEC-SC-2, HM-MOD-Re-8, HM-MOD-Em-8
HM-Wired:  HMW_IO_12_FM, HMW_Sen_SC_12_DR, Selbstbau IO-Module HBW_IO_SW
Maple-SIGNALduino, WH3080,  Hideki, Id 7

andies

Habe ich. Danach wieder ein Gerät eingelesen sowie einmal Somfy (der hat ja nicht 433.92) ausgelöst:
2018.06.02 15:30:52 4: sduino/msg READredu: MU;P0=-24432;P1=791;P2=-915;P3=213;P4=-664;P5=546;P6=-305;P7=-492;D=0121212123456563434565634343456565634343456343437;CP=3;R=218;
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 16 -> Dooya shutter matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 16 -> Dooya shutter mismatches, aborting
2018.06.02 15:30:52 5: sduino: applying filterfunc SIGNALduino_filterSign
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 20 -> livolo matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: Starting demodulation at Position 12
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 24 -> visivon remote matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 24 -> visivon remote mismatches, aborting
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 27 -> remote27 matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 27 -> remote27 mismatches, aborting
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 28 -> IC Ledspot matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 28 -> IC Ledspot mismatches, aborting
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 29 -> HT12e remote matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 29 -> HT12e remote mismatches, aborting
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 30 -> unitec47031 matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 30 -> unitec47031 mismatches, aborting
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 31 -> pollin isotronic matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: Starting demodulation at Position 1
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 37 -> Bresser 7009994 matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: Starting demodulation at Position 4
2018.06.02 15:30:52 5: sduino: applying filterfunc SIGNALduino_compPattern
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 49 -> quigg_gt9000 matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 49 -> quigg_gt9000 mismatches, aborting
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 56 -> Celexon matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 56 -> Celexon mismatches, aborting
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 61 -> FS10 matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: Starting demodulation at Position 9
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 62 -> Clarus_Switch matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 62 -> Clarus_Switch mismatches, aborting
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 69 -> Hoermann matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 69 -> Hoermann mismatches, aborting
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 70 -> FHT80TF matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: Starting demodulation at Position 11
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 72 -> Siro shutter matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 72 -> Siro shutter mismatches, aborting
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 79 -> VTX-BELL_Funkklingel matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 79 -> VTX-BELL_Funkklingel mismatches, aborting
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 8 -> TX3 Protocol matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: Starting demodulation at Position 1
2018.06.02 15:30:52 4: sduino/msg READredu: MU;P0=195;P1=811;P2=-899;P4=-664;P5=558;P6=-307;P7=-30168;D=121212120456560404565604040456565604040456040404040404560404040456560404040456045604565607;CP=0;R=220;w=0;
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 16 -> Dooya shutter matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 16 -> Dooya shutter mismatches, aborting
2018.06.02 15:30:52 5: sduino: applying filterfunc SIGNALduino_filterSign
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 20 -> livolo matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: Starting demodulation at Position 11
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 24 -> visivon remote matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 24 -> visivon remote mismatches, aborting
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 27 -> remote27 matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 27 -> remote27 mismatches, aborting
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 28 -> IC Ledspot matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 28 -> IC Ledspot mismatches, aborting
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 29 -> HT12e remote matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 29 -> HT12e remote mismatches, aborting
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 30 -> unitec47031 matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 30 -> unitec47031 mismatches, aborting
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 31 -> pollin isotronic matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: Starting demodulation at Position 1
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 37 -> Bresser 7009994 matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: Starting demodulation at Position 8
2018.06.02 15:30:52 5: sduino: dispatching bits: 0 1 1 0 0 1 1 0 0 0 1 1 1 0 0 0 1 0 0 0 0 0 0 1 0 0 0 0 1 1 0 0 0 0 1 0 1 0 1 1
2018.06.02 15:30:52 4: sduino: decoded matched MU Protocol id 37 dmsg W37#6638810C2B length 40 RSSI = -92
2018.06.02 15:30:52 5: sduino Dispatch: W37#6638810C2B, test ungleich: disabled
2018.06.02 15:30:52 5: sduino Dispatch: W37#6638810C2B, -92 dB, dispatch
2018.06.02 15:30:52 5: sduino: dispatch W37#6638810C2B
2018.06.02 15:30:52 4: SD_WS_Parse: Protocol: 37, rawData: 6638810C2B
2018.06.02 15:30:52 4: sduino: SD_WS37 checksum ok 43 = 43
2018.06.02 15:30:52 4: sduino: SD_WS37 tempraw = 2177, temp = 127.7 F, temp = 53.2 C, Hum = 12
2018.06.02 15:30:52 4: sduino: SD_WS37 decoded protocol = 37 (Bresser 7009994), sensor id = 66, channel = 3
2018.06.02 15:30:52 1: SD_WS: UNDEFINED sensor SD_WS37_TH detected, code SD_WS37_TH_3
2018.06.02 15:30:52 5: sduino: applying filterfunc SIGNALduino_compPattern
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 49 -> quigg_gt9000 matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 49 -> quigg_gt9000 mismatches, aborting
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 56 -> Celexon matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 56 -> Celexon mismatches, aborting
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 61 -> FS10 matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: Starting demodulation at Position 8
2018.06.02 15:30:52 5: sduino: dispatching bits: 1 0 0 1 1 0 0 1 1 1 0 0 0 1 1 1 0 1 1 1 1 1 1 0 1 1 1 1 0 0 1 1 1 1 0 1 0 1 0 0
2018.06.02 15:30:52 4: sduino: decoded matched MU Protocol id 61 dmsg P61#99C77EF3D4 length 40 RSSI = -92
2018.06.02 15:30:52 5: sduino Dispatch: P61#99C77EF3D4, test ungleich: disabled
2018.06.02 15:30:52 5: sduino Dispatch: P61#99C77EF3D4, -92 dB, dispatch
2018.06.02 15:30:52 5: sduino: dispatch P61#99C77EF3D4
2018.06.02 15:30:52 4: sduino FS10_Parse: Protocol: 61, rawData: 99C77EF3D4
2018.06.02 15:30:52 4: sduino FS10_Parse: rawBitData: 1001100111000111011111101111001111010100 (40)
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 62 -> Clarus_Switch matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 62 -> Clarus_Switch mismatches, aborting
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 69 -> Hoermann matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 69 -> Hoermann mismatches, aborting
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 70 -> FHT80TF matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: Starting demodulation at Position 10
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 72 -> Siro shutter matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 72 -> Siro shutter mismatches, aborting
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 79 -> VTX-BELL_Funkklingel matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 79 -> VTX-BELL_Funkklingel mismatches, aborting
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 8 -> TX3 Protocol matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: Starting demodulation at Position 0
2018.06.02 15:30:52 4: sduino/msg READredu: MU;P0=195;P1=811;P2=-899;P4=-664;P5=558;P6=-307;P7=-30168;D=71212121204565604045656040404565656040404560;CP=0;R=220;
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 16 -> Dooya shutter matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 16 -> Dooya shutter mismatches, aborting
2018.06.02 15:30:52 5: sduino: applying filterfunc SIGNALduino_filterSign
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 20 -> livolo matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: Starting demodulation at Position 12
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 24 -> visivon remote matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 24 -> visivon remote mismatches, aborting
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 27 -> remote27 matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 27 -> remote27 mismatches, aborting
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 28 -> IC Ledspot matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 28 -> IC Ledspot mismatches, aborting
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 29 -> HT12e remote matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 29 -> HT12e remote mismatches, aborting
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 30 -> unitec47031 matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 30 -> unitec47031 mismatches, aborting
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 31 -> pollin isotronic matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: Starting demodulation at Position 1
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 37 -> Bresser 7009994 matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: Starting demodulation at Position 9
2018.06.02 15:30:52 5: sduino: applying filterfunc SIGNALduino_compPattern
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 49 -> quigg_gt9000 matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 49 -> quigg_gt9000 mismatches, aborting
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 56 -> Celexon matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 56 -> Celexon mismatches, aborting
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 61 -> FS10 matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: Starting demodulation at Position 9
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 62 -> Clarus_Switch matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 62 -> Clarus_Switch mismatches, aborting
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 69 -> Hoermann matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 69 -> Hoermann mismatches, aborting
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 70 -> FHT80TF matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: Starting demodulation at Position 11
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 72 -> Siro shutter matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 72 -> Siro shutter mismatches, aborting
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 79 -> VTX-BELL_Funkklingel matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: start pattern for MU Protocol id 79 -> VTX-BELL_Funkklingel mismatches, aborting
2018.06.02 15:30:52 4: sduino: Fingerprint for MU Protocol id 8 -> TX3 Protocol matches, trying to demodulate
2018.06.02 15:30:52 5: sduino: Starting demodulation at Position 1
2018.06.02 15:30:59 5: sduino/write: sending via Set sendMsg P43#AB8988D3DDDDDD#R6
2018.06.02 15:30:59 5: sduino: sendmsg msg=P43#AB8988D3DDDDDD#R6
2018.06.02 15:30:59 5: sduino: sendmsg Preparing manchester protocol=43, repeats=0, clock=645 data=AB8988D3DDDDDD
2018.06.02 15:30:59 5: AddSendQueue: sduino: SC;R=6;SR;P0=-2560;P1=2560;P3=-640;D=10101010101010113;SM;C=645;D=AB8988D3DDDDDD;F=10AB85550A; (1)
2018.06.02 15:30:59 4: sduino/set: sending via SendMsg: SC;R=6;SR;P0=-2560;P1=2560;P3=-640;D=10101010101010113;SM;C=645;D=AB8988D3DDDDDD;F=10AB85550A;
2018.06.02 15:30:59 5: sduino SW: SC;R=6;SR;P0=-2560;P1=2560;P3=-640;D=10101010101010113;SM;C=645;D=AB8988D3DDDDDD;F=10AB85550A;
2018.06.02 15:30:59 4: sduino SendrawFromQueue: msg=SC;R=6;SR;P0=-2560;P1=2560;P3=-640;D=10101010101010113;SM;C=645;D=AB8988D3DDDDDD;F=10AB85550A;
2018.06.02 15:31:00 4: sduino/msg READ: SC;R=6;SR;P0=-2560;P1=2560;P3=-640;D=10101010101010113;SM;C=645;D=AB8988D3DDDDDD;F=10AB85550A;ccreg write back 10B07157C4
2018.06.02 15:31:00 5: sduino/noMsg Parse: SC;R=6;SR;P0=-2560;P1=2560;P3=-640;D=10101010101010113;SM;C=645;D=AB8988D3DDDDDD;F=10AB85550A;ccreg write back 10B07157C4
2018.06.02 15:31:00 5: sduino/msg READ: regexp=^S(R|C|M); cmd=sendraw msg=SC;R=6;SR;P0=-2560;P1=2560;P3=-640;D=10101010101010113;SM;C=645;D=AB8988D3DDDDDD;F=10AB85550A;ccreg write back 10B07157C4
2018.06.02 15:31:00 4: sduino/read sendraw answer: SC;R=6;SR;P0=-2560;P1=2560;P3=-640;D=10101010101010113;SM;C=645;D=AB8988D3DDDDDD;F=10AB85550A;ccreg write back 10B07157C4
2018.06.02 15:31:00 4: sduino/HandleWriteQueue: nothing to send, stopping timer
FHEM 6.3 auf RaspPi4 (Raspbian:  6.6.28+; Perl: v5.36.0)
SIGNALduino (433 MHz) und HM-UART (868 MHz), Sonoff, Blitzwolf, Somfy RTS, CAME-Gartentor, Volkszähler, Keyence-Sensor, Homematic-Sensoren und -thermostat, Ferraris-Zähler für Wasseruhr, Openlink-Nachbau Viessmann

andies

Wie kann ich diese Einträge vermeiden:

018.06.02 21:40:57 3: sduino: SD_WS37 ERROR - checksum 195 != 43
2018.06.02 21:41:54 3: sduino: SD_WS37 ERROR - checksum 195 != 43
2018.06.02 21:42:50 3: sduino: SD_WS37 ERROR - checksum 195 != 43
2018.06.02 21:44:44 3: sduino: SD_WS37 ERROR - checksum 195 != 43
2018.06.02 21:45:42 3: sduino: SD_WS37 ERROR - checksum 195 != 43
2018.06.02 21:46:39 3: sduino: SD_WS37 ERROR - checksum 195 != 43
2018.06.02 21:46:39 3: sduino: SD_WS37 ERROR - checksum 195 != 43
2018.06.02 21:49:29 3: sduino: SD_WS37 ERROR - checksum 195 != 43
2018.06.02 21:50:26 3: sduino: SD_WS37 ERROR - checksum 196 != 73
2018.06.02 21:51:23 3: sduino: SD_WS37 ERROR - checksum 195 != 43
2018.06.02 21:51:48 3: sduino: SD_WS37 ERROR - checksum 7 != 131
2018.06.02 21:52:21 3: sduino: SD_WS37 ERROR - checksum 195 != 43
2018.06.02 21:54:15 3: sduino: SD_WS37 ERROR - checksum 194 != 141



Gesendet von iPad mit Tapatalk Pro
FHEM 6.3 auf RaspPi4 (Raspbian:  6.6.28+; Perl: v5.36.0)
SIGNALduino (433 MHz) und HM-UART (868 MHz), Sonoff, Blitzwolf, Somfy RTS, CAME-Gartentor, Volkszähler, Keyence-Sensor, Homematic-Sensoren und -thermostat, Ferraris-Zähler für Wasseruhr, Openlink-Nachbau Viessmann

Ralf9

2018.06.02 15:30:52 5: sduino Dispatch: W37#6638810C2B, -92 dB, dispatch
-92 dB sind grenzwertig.
Ist der SD_WS37 etwas weiter vom sduino weg?

Gruß Ralf
FHEM auf Cubietruck mit Igor-Image, SSD und  hmland + HM-CFG-USB-2,  HMUARTLGW Lan,   HM-LC-Bl1PBU-FM, HM-CC-RT-DN, HM-SEC-SC-2, HM-MOD-Re-8, HM-MOD-Em-8
HM-Wired:  HMW_IO_12_FM, HMW_Sen_SC_12_DR, Selbstbau IO-Module HBW_IO_SW
Maple-SIGNALduino, WH3080,  Hideki, Id 7

andies

#109
Der ist nicht bei mir, den hat der Nachbar (vermutlich). Ist das mit der Frequenz geklärt?

(Ich habe jetzt 37 auf die Blacklist gesetzt und die Meldung kommt nicht mehr.)
FHEM 6.3 auf RaspPi4 (Raspbian:  6.6.28+; Perl: v5.36.0)
SIGNALduino (433 MHz) und HM-UART (868 MHz), Sonoff, Blitzwolf, Somfy RTS, CAME-Gartentor, Volkszähler, Keyence-Sensor, Homematic-Sensoren und -thermostat, Ferraris-Zähler für Wasseruhr, Openlink-Nachbau Viessmann

Ralf9

Das mit der Frequenz sieht im log gut aus. Hast Du damit noch Probleme?

Als Alternative zur Blacklist wäre, Sidey zu bitten den loglevel der  checksum Fehlermeldung von 3 auf 4 zu erhöhen.
14_SD_WS.pm Zeile 253
Log3 $name, 3, "$name: SD_WS37 ERROR - checksum $checksum != ".SD_WS_binaryToNumber($bitData,32,39);

Gruß Ralf
FHEM auf Cubietruck mit Igor-Image, SSD und  hmland + HM-CFG-USB-2,  HMUARTLGW Lan,   HM-LC-Bl1PBU-FM, HM-CC-RT-DN, HM-SEC-SC-2, HM-MOD-Re-8, HM-MOD-Em-8
HM-Wired:  HMW_IO_12_FM, HMW_Sen_SC_12_DR, Selbstbau IO-Module HBW_IO_SW
Maple-SIGNALduino, WH3080,  Hideki, Id 7

andies

Bisher läuft alles bestens. Ich habe verbose auf 0 und brauche diese anderen Geräte nicht, ich habe ja nur drei hier. Vielen Dank für die Reparatur!
FHEM 6.3 auf RaspPi4 (Raspbian:  6.6.28+; Perl: v5.36.0)
SIGNALduino (433 MHz) und HM-UART (868 MHz), Sonoff, Blitzwolf, Somfy RTS, CAME-Gartentor, Volkszähler, Keyence-Sensor, Homematic-Sensoren und -thermostat, Ferraris-Zähler für Wasseruhr, Openlink-Nachbau Viessmann

Ralf9

Zitat"get sduino uptime" Fehler behoben (nun funktioniert auch größer 49 Tage).
Hier ist meine aktuelle uptime:
uptime 53 18:55:36


ZitatIch habe auch eine Erkennung von Wiederholungen bei MU-Nachrichten eingebaut. Dies ist noch experimentell es kann sein, das dies nicht bei allen MU-Nachrichten funktioniert. Ein w am Ende der Nachricht bedeutet, das eine mögliche Wiederholung erkannt wurde.
Es gibt eine neue Konfigvariable muthresh, damit wird der Schwellwert für den split von MU Nachrichten festgelegt.
Mit CSmuthresh=8000 werden z.B. die MU Nachrichten nach einer Pause größer 8 ms gesucht und dort die Nachricht abgetrennt.

Beim analysieren von unbekannten Protokollen kann es sinnvoll sein die Erkennung von Wiederholungen bei MU-Nachrichten abzuschalten:
get sduino raw CSmuthresh=0

Gruß Ralf
FHEM auf Cubietruck mit Igor-Image, SSD und  hmland + HM-CFG-USB-2,  HMUARTLGW Lan,   HM-LC-Bl1PBU-FM, HM-CC-RT-DN, HM-SEC-SC-2, HM-MOD-Re-8, HM-MOD-Em-8
HM-Wired:  HMW_IO_12_FM, HMW_Sen_SC_12_DR, Selbstbau IO-Module HBW_IO_SW
Maple-SIGNALduino, WH3080,  Hideki, Id 7

Ralf9

Wenn mit einem https link z.B. von https://raw.githubusercontent.com/ geflasht wird, dann wird beim flashen kein flash log ausgegeben.

z.B. bei
set sduinoRXB flash https://raw.githubusercontent.com/Ralf9/SIGNALDuino/dev-r332_cc1101/firmware/SIGNALduino_nano_332rc1.hex

steht in etwa folgendes im fhem log:
2018.07.25 21:15:58.028 3 : url https://raw.githubusercontent.com/Ralf9/SIGNALDuino/dev-r332_cc1101/firmware/SIGNALduino_nano_332rc1.hex returned: 85276 bytes Data
2018.07.25 21:15:58.028 3 : sduinoRXB: Downloaded SIGNALduino_nano_332rc1.hex firmware from raw.githubusercontent.com
2018.07.25 21:15:58.029 5 : sduinoRXB: Header = HTTP/1.1 200 OK Content-Security-Policy: default-src 'none'; style-src 'unsafe-inline'; sandbox Strict-Transport-Security: max-age=31536000 X-Content-Type-Options: nosniff X-Frame-Options: deny X-XSS-Protection: 1; mode=block ETag: "8aae23ec6b263230a24c342cf5ba29ee9a5ce314" Content-Type: text/plain; charset=utf-8 Cache-Control: max-age=300 X-Geo-Block-List: X-GitHub-Request-Id: E798:1891:A168F3:AB1F70:5B58CC6D Content-Length: 85276 Accept-Ranges: bytes Date: Wed, 25 Jul 2018 19:15:57 GMT Via: 1.1 varnish Connection: close X-Served-By: cache-hhn1538-HHN X-Cache: MISS X-Cache-Hits: 0 X-Timer: S1532546158.845393,VS0,VE140 Vary: Authorization,Accept-Encoding Access-Control-Allow-Origin: * X-Fastly-Request-ID: f0cd834df3f45e9c28ed2a1206c7bf591ea6770a Expires: Wed, 25 Jul 2018 19:20:57 GMT Source-Age: 0
2018.07.25 21:15:58.029 3 : calling set flash FHEM/firmware/SIGNALduino_nano_332rc1.hex
2018.07.25 21:15:58.030 3 : sduinoRXB: filename FHEM/firmware/SIGNALduino_nano_332rc1.hex provided, trying to flash



Der flash log steht in der Datei "SIGNALduino-Flash.log" im log Verzeichnis.
z.B.:
avrdude: Version 6.3, (openSUSE Buildservice)
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2014 Joerg Wunsch

         System wide configuration file is "/etc/avrdude.conf"
         User configuration file is "/home/ralf/.avrduderc"
         User configuration file does not exist or is not a regular file, skipping

         Using Port                    : /dev/serial/by-id/usb-FTDI_FT232R_USB_UART_A9GFBXLP-if00-port0
         Using Programmer              : arduino
         Overriding Baud Rate          : 57600
         AVR Part                      : ATmega328P
         Chip Erase delay              : 9000 us
         PAGEL                         : PD7
         BS2                           : PC2
         RESET disposition             : dedicated
         RETRY pulse                   : SCK
         serial program mode           : yes
         parallel program mode         : yes
         Timeout                       : 200
         StabDelay                     : 100
         CmdexeDelay                   : 25
         SyncLoops                     : 32
         ByteDelay                     : 0
         PollIndex                     : 3
         PollValue                     : 0x53
         Memory Detail                 :

                                  Block Poll               Page                       Polled
           Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
           ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
           eeprom        65    20     4    0 no       1024    4      0  3600  3600 0xff 0xff
           flash         65     6   128    0 yes     32768  128    256  4500  4500 0xff 0xff
           lfuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           hfuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           efuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           lock           0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           calibration    0     0     0    0 no          1    0      0     0     0 0x00 0x00
           signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00

         Programmer Type : Arduino
         Description     : Arduino
         Hardware Version: 2
         Firmware Version: 1.16
         Vtarget         : 0.0 V
         Varef           : 0.0 V
         Oscillator      : Off
         SCK period      : 0.1 us

avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.00s

avrdude: Device signature = 0x1e950f (probably m328p)
avrdude: NOTE: "flash" memory has been specified, an erase cycle will be performed
         To disable this feature, specify the -D option.
avrdude: erasing chip
avrdude: reading input file "FHEM/firmware/SIGNALduino_nano_332rc1.hex"
avrdude: input file FHEM/firmware/SIGNALduino_nano_332rc1.hex auto detected as Intel Hex
avrdude: writing flash (30314 bytes):

Writing | ################################################## | 100% 8.30s

avrdude: 30314 bytes of flash written
avrdude: verifying flash memory against FHEM/firmware/SIGNALduino_nano_332rc1.hex:
avrdude: load data flash data from input file FHEM/firmware/SIGNALduino_nano_332rc1.hex:
avrdude: input file FHEM/firmware/SIGNALduino_nano_332rc1.hex auto detected as Intel Hex
avrdude: input file FHEM/firmware/SIGNALduino_nano_332rc1.hex contains 30314 bytes
avrdude: reading on-chip flash data:

Reading | ################################################## | 100% 6.16s

avrdude: verifying ...
avrdude: 30314 bytes of flash verified

avrdude done.  Thank you.


Gruß Ralf
FHEM auf Cubietruck mit Igor-Image, SSD und  hmland + HM-CFG-USB-2,  HMUARTLGW Lan,   HM-LC-Bl1PBU-FM, HM-CC-RT-DN, HM-SEC-SC-2, HM-MOD-Re-8, HM-MOD-Em-8
HM-Wired:  HMW_IO_12_FM, HMW_Sen_SC_12_DR, Selbstbau IO-Module HBW_IO_SW
Maple-SIGNALduino, WH3080,  Hideki, Id 7

l2r

Zitat von: Ralf9 am 14 Februar 2018, 12:06:33
Hier ist ein aktuelles kompiliertes hex file (SIGNALduino_radinoCC1101_332r.hex). Da ich keine radino habe, konnte ich nicht testen ob ich es richtig kompiliert habe
https://github.com/Ralf9/SIGNALDuino/tree/dev-r332_cc1101/firmware

Bitte schau mal ob diese kurze Anleitung fürs flashen ausreichend ist:
https://forum.fhem.de/index.php/topic,58397.msg762083.html#msg762083

Gruß Ralf

hallo Ralf

ich habe folgenden Stick bei mir im Einsatz:

https://shop.in-circuit.de/product_info.php?products_id=253

mit diesem versuche ich folgende Wetterstation abzugreifen:
https://www.lidl.de/de/auriol-funk-wetterstation/p256157

Anleitung (Seite 8 für technische Infos):
https://www.lidl-service.com/static/1414890947/283582_PL.pdf


FHEM erkennt den sduino nur leider kann er mit den empfangenen Signalen nicht umgehen:

Logauszug:

2018.08.08 17:24:29 3: sduino: Unknown code u40#4E024870, help me!
2018.08.08 17:24:29 3: sduino: Unknown code u40#4824E024870, help me!
2018.08.08 17:24:29 3: sduino: Unknown code u40#4924E024870, help me!
2018.08.08 17:25:30 3: sduino: Unknown code u40#4904E024870, help me!
2018.08.08 17:25:30 3: sduino: Unknown code u40#4824E024870, help me!
2018.08.08 17:25:30 3: sduino: Unknown code u40#4924E024870, help me!
2018.08.08 17:25:31 3: sduino: Unknown code u40#4824E024870, help me!
2018.08.08 17:25:31 3: sduino: Unknown code u40#4924E024870, help me!
2018.08.08 17:26:01 3: sduino: Unknown code u40#09380921C, help me!
2018.08.08 17:26:01 3: sduino: Unknown code u40#490E6024870, help me!
2018.08.08 17:26:01 3: sduino: Unknown code u40#4E024870, help me!
2018.08.08 17:26:02 3: sduino: Unknown code u40#490E6024870, help me!
2018.08.08 17:27:03 3: sduino: Unknown code u40#4924E024870, help me!
2018.08.08 17:27:03 3: sduino: Unknown code u40#490E6024870, help me!
2018.08.08 17:29:07 3: sduino: Unknown code u40#4924E024A10, help me!
2018.08.08 17:29:07 3: sduino: Unknown code u40#4824E024A10, help me!
2018.08.08 17:29:08 3: sduino: Unknown code u40#4924E024A10, help me!
2018.08.08 17:29:08 3: sduino: Unknown code u40#4824E024A10, help me!
2018.08.08 17:30:09 3: sduino: Unknown code u40#127012508, help me!
2018.08.08 17:30:09 3: sduino: Unknown code u40#4824E024A10, help me!
2018.08.08 17:30:10 3: sduino: Unknown code u40#093809284, help me!
2018.08.08 17:30:10 3: sduino: Unknown code u40#4824E024A10, help me!
2018.08.08 17:30:10 3: sduino: Unknown code u40#093809284, help me!
2018.08.08 17:30:40 3: sduino: Unknown code u40#4924E024A10, help me!
2018.08.08 17:30:40 3: sduino: Unknown code u40#49420, help me!
2018.08.08 17:30:40 3: sduino: Unknown code u40#024A10, help me!
2018.08.08 17:30:40 3: sduino: Unknown code u40#49420, help me!
2018.08.08 17:30:40 3: sduino: Unknown code u40#024A10, help me!
2018.08.08 17:30:41 3: sduino: Unknown code u40#49420, help me!
2018.08.08 17:30:41 3: sduino: Unknown code u40#024A10, help me!
2018.08.08 17:30:41 3: sduino: Unknown code u40#49420, help me!
2018.08.08 17:30:41 3: sduino: Unknown code u40#024A10, help me!
2018.08.08 17:30:41 3: sduino: Unknown code u40#4924E024A10, help me!
2018.08.08 17:31:42 3: sduino: Unknown code u40#4940, help me!
2018.08.08 17:31:42 3: sduino: Unknown code u40#7012508, help me!
2018.08.08 17:31:42 3: sduino: Unknown code u40#4924E024A10, help me!
2018.08.08 17:31:43 3: sduino: Unknown code u40#4944E024A10, help me!
2018.08.08 17:31:43 3: sduino: Unknown code u40#4940, help me!
2018.08.08 17:31:43 3: sduino: Unknown code u40#7012508, help me!
2018.08.08 17:31:43 3: sduino: Unknown code u40#4940, help me!
2018.08.08 17:31:43 3: sduino: Unknown code u40#7012508, help me!


List vom sduino:
Internals:
   Clients    :IT:CUL_TCM97001:SD_RSL:OREGON:CUL_TX:SD_AS:Hideki:SD_WS07:SD_WS09: :SD_WS:RFXX10REC:Dooya:SOMFY:SD_UT:SD_WS_Maverick:FLAMINGO:CUL_WS:Revolt: :FS10:CUL_FHTTK:Siro:FHT:FS20:SIGNALduino_un:
   DEF        /dev/ttyACM0
   DMSG       nothing
   DevState   disconnected
   DeviceName /dev/ttyACM0@57600
   LASTDMSG   nothing
   NAME       sduino
   NR         248
   PARTIAL   
   STATE      disconnected
   TIME       1533803065.09469
   TYPE       SIGNALduino
   versionmodul v3.3.3-dev_20.04.
   MatchList:
     10:SD_WS07 ^P7#[A-Fa-f0-9]{6}F[A-Fa-f0-9]{2}(#R[A-F0-9][A-F0-9]){0,1}$
     11:SD_WS09 ^P9#F[A-Fa-f0-9]+
     12:SD_WS   ^W\d+x{0,1}#.*
     13:RFXX10REC ^(20|29)[A-Fa-f0-9]+
     14:Dooya   ^P16#[A-Fa-f0-9]+
     15:SOMFY   ^Ys[0-9A-F]+
     16:SD_WS_Maverick ^P47#[A-Fa-f0-9]+
     17:SD_UT   ^u30#.*
     18:FLAMINGO ^P13#[A-Fa-f0-9]+
     19:CUL_WS  ^K[A-Fa-f0-9]{5,}
     1:IT       ^i......
     20:Revolt  ^r[A-Fa-f0-9]{22}
     21:FS10    ^P61#[A-F0-9]+
     22:Siro    ^P72#[A-Fa-f0-9]+
     23:FHT     ^81..(04|09|0d)..(0909a001|83098301|c409c401)..
     24:FS20    ^81..(04|0c)..0101a001
     2:CUL_TCM97001 ^s[A-Fa-f0-9]+
     3:SD_RSL   ^P1#[A-Fa-f0-9]{8}
     4:OREGON   ^(3[8-9A-F]|[4-6][0-9A-F]|7[0-8]).*
     5:CUL_TX   ^TX..........
     6:SD_AS    ^P2#[A-Fa-f0-9]{7,8}
     7:Hideki   ^P12#75[A-F0-9]+
     9:CUL_FHTTK ^T[A-F0-9]{8}
     X:SIGNALduino_un ^[u]\d+#.*
   READINGS:
     2018-08-08 17:56:56   ccconf          freq:433.920MHz bWidth:325KHz rAmpl:42dB sens:8dB  (DataRate:5603.79Baud)
     2018-08-06 16:17:32   config          MS=1;MU=1;MC=1
     2018-08-08 12:26:41   ping            OK
     2018-08-09 10:24:25   state           disconnected
     2018-08-08 17:57:04   version         V 3.3.1-dev SIGNALduino cc1101 (433Mhz )- compiled at Mar 10 2017 23:27:29
   mcIdList:
     10
     11
     12
     18
     43
     47
     52
     57
     58
   msIdList:
     0
     1
     2
     3
     3.1
     4
     6
     7
     13
     13.2
     14
     15
     17
     22
     23
     25
     32
     33
     35
     38
     41
     51
     55
     65
     68
     72.1
   muIdList:
     5
     8
     9
     13.1
     16
     20
     21
     24
     26
     27
     28
     29
     30
     31
     36
     37
     39
     40
     44
     44.1
     45
     46
     48
     49
     50
     56
     59
     60
     61
     62
     64
     66
     67
     69
     70
     71
     72
     75
     79
Attributes:
   flashCommand avrdude -c arduino -b [BAUDRATE] -P [PORT] -p atmega328p -vv -U flash:w:[HEXFILE] 2>[LOGFILE]
   hardware   nanoCC1101
   room       I/O


ich habe jetzt versucht die Beta-Firmware 332 zu flashen.
Den Befehl habe ich direkt auf der Raspberry pi ausgeführt.
Leider erfolglos:

avrdude -v -p atmega32u4 -c avr109 -P /dev/ttyACM0 -b57600 -D -V -U flash:w:SIGNALduino_radinoCC1101_332r.hex:i

avrdude: Version 6.3-20171130
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2014 Joerg Wunsch

         System wide configuration file is "/etc/avrdude.conf"
         User configuration file is "/home/pi/.avrduderc"
         User configuration file does not exist or is not a regular file, skipping

         Using Port                    : /dev/ttyACM0
         Using Programmer              : avr109
         Overriding Baud Rate          : 57600
         AVR Part                      : ATmega32U4
         Chip Erase delay              : 9000 us
         PAGEL                         : PD7
         BS2                           : PA0
         RESET disposition             : dedicated
         RETRY pulse                   : SCK
         serial program mode           : yes
         parallel program mode         : yes
         Timeout                       : 200
         StabDelay                     : 100
         CmdexeDelay                   : 25
         SyncLoops                     : 32
         ByteDelay                     : 0
         PollIndex                     : 3
         PollValue                     : 0x53
         Memory Detail                 :

                                  Block Poll               Page                       Polled
           Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
           ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
           eeprom        65    20     4    0 no       1024    4      0  9000  9000 0x00 0x00
           flash         65     6   128    0 yes     32768  128    256  4500  4500 0x00 0x00
           lfuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           hfuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           efuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           lock           0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           calibration    0     0     0    0 no          1    0      0     0     0 0x00 0x00
           signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00

         Programmer Type : butterfly
         Description     : Atmel AppNote AVR109 Boot Loader

Connecting to programmer: .
Found programmer: Id = "CATERIN"; type = S
    Software Version = 1.0; No Hardware Version given.
Programmer supports auto addr increment.
Programmer supports buffered memory access with buffersize=128 bytes.

Programmer supports the following devices:
    Device code: 0x44

avrdude: devcode selected: 0x44
avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.00s

avrdude: Device signature = 0x1e9587 (probably m32u4)
avrdude: safemode: lfuse reads as FF
avrdude: safemode: hfuse reads as D8
avrdude: safemode: efuse reads as CB
avrdude: reading input file "SIGNALduino_radinoCC1101_332r.hex"
avrdude: ERROR: No valid record found in Intel Hex file "SIGNALduino_radinoCC1101_332r.hex"
avrdude: read from file 'SIGNALduino_radinoCC1101_332r.hex' failed

avrdude: safemode: lfuse reads as FF
avrdude: safemode: hfuse reads as D8
avrdude: safemode: efuse reads as CB
avrdude: safemode: Fuses OK (E:CB, H:D8, L:FF)

avrdude done.  Thank you.



den radinoCC1101 konnte ich problemlos flashen:

avrdude -v -p atmega32u4 -c avr109 -P /dev/ttyACM0 -b57600 -D -V -U flash:w:SIGNALDuino_radinoCC1101.hex:i

avrdude: Version 6.3-20171130
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2014 Joerg Wunsch

         System wide configuration file is "/etc/avrdude.conf"
         User configuration file is "/home/pi/.avrduderc"
         User configuration file does not exist or is not a regular file, skipping

         Using Port                    : /dev/ttyACM0
         Using Programmer              : avr109
         Overriding Baud Rate          : 57600
         AVR Part                      : ATmega32U4
         Chip Erase delay              : 9000 us
         PAGEL                         : PD7
         BS2                           : PA0
         RESET disposition             : dedicated
         RETRY pulse                   : SCK
         serial program mode           : yes
         parallel program mode         : yes
         Timeout                       : 200
         StabDelay                     : 100
         CmdexeDelay                   : 25
         SyncLoops                     : 32
         ByteDelay                     : 0
         PollIndex                     : 3
         PollValue                     : 0x53
         Memory Detail                 :

                                  Block Poll               Page                       Polled
           Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
           ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
           eeprom        65    20     4    0 no       1024    4      0  9000  9000 0x00 0x00
           flash         65     6   128    0 yes     32768  128    256  4500  4500 0x00 0x00
           lfuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           hfuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           efuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           lock           0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           calibration    0     0     0    0 no          1    0      0     0     0 0x00 0x00
           signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00

         Programmer Type : butterfly
         Description     : Atmel AppNote AVR109 Boot Loader

Connecting to programmer: .
Found programmer: Id = "CATERIN"; type = S
    Software Version = 1.0; No Hardware Version given.
Programmer supports auto addr increment.
Programmer supports buffered memory access with buffersize=128 bytes.

Programmer supports the following devices:
    Device code: 0x44

avrdude: devcode selected: 0x44
avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.00s

avrdude: Device signature = 0x1e9587 (probably m32u4)
avrdude: safemode: lfuse reads as FF
avrdude: safemode: hfuse reads as D8
avrdude: safemode: efuse reads as CB
avrdude: reading input file "SIGNALDuino_radinoCC1101.hex"
avrdude: writing flash (23080 bytes):

Writing | ################################################## | 100% 3.02s

avrdude: 23080 bytes of flash written

avrdude: safemode: lfuse reads as FF
avrdude: safemode: hfuse reads as D8
avrdude: safemode: efuse reads as CB
avrdude: safemode: Fuses OK (E:CB, H:D8, L:FF)

avrdude done.  Thank you.


Ich hoffe die Logauszüge sind hilfreich. Wenn du noch mehr Infos benötigst, dann melde dich bitte.

Vielen Dank schonmal

Gruß Michael
Wissen ist Macht.
Ich weiß nix.
Macht nix.

Ralf9

Bitte versuche mal folgendes:
set sduino flash https://raw.githubusercontent.com/Ralf9/SIGNALDuino/dev-r332_cc1101/firmware/SIGNALduino_radinoCC1101_332r.hex

ZitatFHEM erkennt den sduino nur leider kann er mit den empfangenen Signalen nicht umgehen:

evtl ist mit den raw Nachrichten mehr zu erkennen (sduino verbose 4)

Gruß Ralf
FHEM auf Cubietruck mit Igor-Image, SSD und  hmland + HM-CFG-USB-2,  HMUARTLGW Lan,   HM-LC-Bl1PBU-FM, HM-CC-RT-DN, HM-SEC-SC-2, HM-MOD-Re-8, HM-MOD-Em-8
HM-Wired:  HMW_IO_12_FM, HMW_Sen_SC_12_DR, Selbstbau IO-Module HBW_IO_SW
Maple-SIGNALduino, WH3080,  Hideki, Id 7

l2r

hi,

hatte ich auch mal getestet, leider aber nicht mit Verbose 4.

Aktuell habe ich meinen Signauduino durch die ganze flasherei wohl zerschossen. Er wird weder bei Windows noch Linux erkannt ....

Sobald ich den wieder hinbekommen haben sollte, werde ich den gewünschten Test durchführen.

Gruß Michael
Wissen ist Macht.
Ich weiß nix.
Macht nix.

l2r

hi,

so läuft wieder. Hier die Logs:

Flashlog:
avrdude: Version 6.3-20171130
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2014 Joerg Wunsch

         System wide configuration file is "/etc/avrdude.conf"

         Using Port                    : /dev/ttyACM0
         Using Programmer              : arduino
         Overriding Baud Rate          : 57600
ioctl("TIOCMSET"): Broken pipe
ioctl("TIOCMSET"): Broken pipe
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x3f
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x3f
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x3f
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x3f
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x3f
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x3f
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x3f
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x3f
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x3f
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x3f


und das FHEM-Log mit Verbose 4:

2018.08.10 10:28:24 3: sduino: setting Verbose to: 4
2018.08.10 10:28:44 1: /dev/ttyACM0 disconnected, waiting to reappear (sduino)
2018.08.10 10:28:47 3: Setting sduino serial parameters to 57600,8,N,1
2018.08.10 10:28:47 1: sduino/define: /dev/ttyACM0
2018.08.10 10:28:47 1: sduino/init: /dev/ttyACM0
2018.08.10 10:28:47 1: /dev/ttyACM0 reappeared (sduino)
2018.08.10 10:28:49 3: sduino/init: disable receiver (XQ)
2018.08.10 10:28:49 3: url https://raw.githubusercontent.com/Ralf9/SIGNALDuino/dev-r332_cc1101/firmware/SIGNALduino_radinoCC1101_332r.hex returned: 79663 bytes Data
2018.08.10 10:28:49 3: sduino: Downloaded SIGNALduino_radinoCC1101_332r.hex firmware from raw.githubusercontent.com
2018.08.10 10:28:49 3: sduino: filename FHEM/firmware/SIGNALduino_radinoCC1101_332r.hex provided, trying to flash
2018.08.10 10:28:51 3: Opening sduino device /dev/ttyACM0
2018.08.10 10:28:51 3: Setting sduino serial parameters to 57600,8,N,1
2018.08.10 10:28:51 1: sduino/define: /dev/ttyACM0
2018.08.10 10:28:51 1: sduino/init: /dev/ttyACM0
2018.08.10 10:28:51 3: sduino device opened
2018.08.10 10:28:52 3: sduino/init: disable receiver (XQ)
2018.08.10 10:28:53 3: sduino/init: get version, retry = 0
2018.08.10 10:28:53 1: /dev/ttyACM0 disconnected, waiting to reappear (sduino)
2018.08.10 10:28:58 3: Setting sduino serial parameters to 57600,8,N,1
2018.08.10 10:28:58 1: sduino/define: /dev/ttyACM0
2018.08.10 10:28:58 1: sduino/init: /dev/ttyACM0
2018.08.10 10:28:58 1: /dev/ttyACM0 reappeared (sduino)
2018.08.10 10:28:58 4: sduino/msg READ: Reading values fom eeprom
2018.08.10 10:28:58 4: sduino/msg READ: Received answer (Reading values fom eeprom) for version does not match V\s.*SIGNAL(duino|ESP).*
2018.08.10 10:28:58 4: sduino/msg READ: CCVersion=20
2018.08.10 10:28:58 4: sduino/msg READ: Received answer (CCVersion=20) for version does not match V\s.*SIGNAL(duino|ESP).*
2018.08.10 10:28:58 4: sduino/msg READ: CCPartnum=0
2018.08.10 10:28:58 4: sduino/msg READ: Received answer (CCPartnum=0) for version does not match V\s.*SIGNAL(duino|ESP).*
2018.08.10 10:28:58 4: sduino/msg READ: CC1101 found
2018.08.10 10:28:58 4: sduino/msg READ: Received answer (CC1101 found) for version does not match V\s.*SIGNAL(duino|ESP).*
2018.08.10 10:28:58 4: sduino/msg READ: Starting timerjob
2018.08.10 10:28:58 4: sduino/msg READ: Received answer (Starting timerjob) for version does not match V\s.*SIGNAL(duino|ESP).*
2018.08.10 10:28:58 4: sduino/msg READ: receiver enabled
2018.08.10 10:28:58 4: sduino/msg READ: Received answer (receiver enabled) for version does not match V\s.*SIGNAL(duino|ESP).*
2018.08.10 10:28:59 3: sduino/init: disable receiver (XQ)
2018.08.10 10:29:00 3: sduino/init: get version, retry = 0
2018.08.10 10:29:00 4: sduino/msg READ: V 3.3.1-dev SIGNALduino cc1101 (433Mhz )- compiled at Mar 10 2017 23:27:29
2018.08.10 10:29:00 2: sduino: initialized. v3.3.2
2018.08.10 10:29:00 3: sduino/init: enable receiver (XE)


ich hoffe das hilft weiter.

P.S.: Auf meinem Haupt-Fhem hatte ich gestern Abend gesehen, dass die Wetterstation wohl doch empfangen wurde und auch ein DEVICE angelegt hat. Somit komme ich wahrscheinlich auch mit der alten Firmware zurecht. Ich werde das heute nochmals testen.

Gruß Michael
Wissen ist Macht.
Ich weiß nix.
Macht nix.

Ralf9

#118
Zitat2018.08.10 10:28:49 3: sduino: filename FHEM/firmware/SIGNALduino_radinoCC1101_332r.hex provided, trying to flash

2018.08.10 10:29:00 4: sduino/msg READ: V 3.3.1-dev SIGNALduino cc1101 (433Mhz )- compiled at Mar 10 2017 23:27:29

ZitatP.S.: Auf meinem Haupt-Fhem hatte ich gestern Abend gesehen, dass die Wetterstation wohl doch empfangen wurde und auch ein DEVICE angelegt hat. Somit komme ich wahrscheinlich auch mit der alten Firmware zurecht. Ich werde das heute nochmals testen.

Es sieht so aus als hätte das flashen der SIGNALduino_radinoCC1101_332r.hex nicht funktioniert, mit get version wird die alte firmware "V 3.3.1-dev SIGNALduino cc1101 (433Mhz )- compiled at Mar 10 2017" angezeigt.

Die Wetterstation sollte aber auch von der alten Firmware erkannt werden.

Evtl ist in fhem ein update auf die dev-r33 notwendig
update all https://raw.githubusercontent.com/RFD-FHEM/RFFHEM/dev-r33/controls_signalduino.txt

Gruß Ralf
FHEM auf Cubietruck mit Igor-Image, SSD und  hmland + HM-CFG-USB-2,  HMUARTLGW Lan,   HM-LC-Bl1PBU-FM, HM-CC-RT-DN, HM-SEC-SC-2, HM-MOD-Re-8, HM-MOD-Em-8
HM-Wired:  HMW_IO_12_FM, HMW_Sen_SC_12_DR, Selbstbau IO-Module HBW_IO_SW
Maple-SIGNALduino, WH3080,  Hideki, Id 7

l2r

ja genauso ist es!

die Frage ist warum, das nicht funktioniert hat?!

Gruß Michael
Wissen ist Macht.
Ich weiß nix.
Macht nix.