D1-Mini mit PulsCounter

[hugo]

Schönen Abend
Ich möchte mit mit einem Pulscounter TCR5000 und einem D1-Mini Impulse zählen.
Der D1-Mini wurde mit ESP-Mega    20241222 - Mega geflascht und der TCR5000 angeschlossen. 5V, Ground und D3 am D1-Mini.
Den D1-Mini kann ich per Browser öffnen und das Device eingerichtet. Allerdings werden die Counts nicht gezählt obwohl die LED am TRC5000 an und aus geht bei Näherung.
Wo kann das Problem liegen.

Code Auswählen Erweitern

System Info   
Unit Number:    0
Local Time:    2025-02-26 19:13:28
Time Source:    NTP
Time Wander:    0.000 [ppm]
Uptime:    00h10m
Load:    5.49 [%] (LC=6873)
CPU Eco Mode:    false
Boot:    Cold Boot (0)
Reset Reason:    External System
Last Action before Reboot:    Background Task
SW WD count:    0
Memory
Free RAM:    15088 [byte]
Heap Max Free Block:    14136 [byte]
Heap Fragmentation:    7 [%]
Free Stack:    3600 [byte]
Network
IP Config:    Static
IP / Subnet:    192.168.12.180 / 255.255.255.0
Gateway:    192.168.12.10
Client IP:    192.168.12.89
DNS:    8.8.8.8 / (IP unset)
Allowed IP Range:    192.168.12.0 - 192.168.12.255
Connected:    00:10:01.387
Number Reconnects:    0
WiFi ?
WiFi Connection:    802.11n (RSSI -57 dBm)
SSID:    WLAN-001A4F962102 (48:5D:35:F6:79:59)
Channel:    8
Encryption Type:    WPA2/PSK   
STA MAC:    84:F3:EB:E3:8F:2A
AP MAC:    86:F3:EB:E3:8F:2A
WiFi Settings
Force WiFi B/G:    false
Restart WiFi Lost Conn:    false
Force WiFi No Sleep:    false
Periodical send Gratuitous ARP:    false
Connection Failure Threshold:    0
Max WiFi TX Power:    17.50 [dBm]
Current WiFi TX Power:    7.00 [dBm]
WiFi Sensitivity Margin:    3 [dB]
Send With Max TX Power:    false
Extra WiFi scan loops:    0
Use Last Connected AP from RTC:    false
Extra Wait WiFi Connect:    false
Hidden SSID Slow Connect:    true
Include Hidden SSID:    false
Enable SDK WiFi Auto Reconnect:    false
Firmware
Build:⋄    20241222 - Mega
System Libraries:⋄    ESP82xx Core 2843a5ac, NONOS SDK 2.2.2-dev(38a443e), LWIP: 2.1.2 PUYA support
Git Build:⋄    mega-20241222
Plugin Count:    47 ["Normal","No Debug Log"]
Build Origin:    GitHub Actions
Build Time:    Dec 22 2024 23:45:07
Binary Filename:    ESP_Easy_mega_20241222_normal_ESP8266_4M1M
Build Platform:    Linux-6.5.0-1025-azure-x86_64-with-glibc2.35
Git HEAD:    HEAD_8977d4d
System Status
Syslog Log Level:    None
Serial Log Level:    Info
Web Log Level:    None
Enable Serial Port Console:    true
Console Serial Port:    HW Serial0 RX:3 TX:1 @ 115200 baud
Network Services
Network Connected:    ✔
NTP Initialized:    ✔
ESP Board
ESP Chip ID:    14913322 (0xE38F2A)
ESP Chip Frequency:    80 [MHz]
ESP Chip Model:    ESP8266EX
ESP Chip Cores:    1
ESP Board Name:    Espressif Generic ESP8266 ESPEasy 4M Flash 1M FS
Storage
Flash Chip ID:    Vendor: 0x5E Device: 0x4016
Flash Chip Real Size:    4096 [kB]
Flash IDE Size:    4096 [kB]
Flash Chip Speed:    40 [MHz]
Flash IDE Speed:    40 [MHz]
Flash IDE Mode:    DOUT
Flash Writes:    3 daily / 3 boot
Sketch Size:    1003 [kB] (2068 kB free)
Max. OTA Sketch Size:    1019 [kB] (1044464 bytes)
OTA possible:    true
OTA 2-step Needed:    false
SPIFFS Size:    934 [kB] (844 kB free)
Page size:    256 [byte]
Block size:    8192 [byte]
Number of blocks:    116
Maximum open files:    5
Maximum path length:    32

Gruß Josef

[Bison]

Hallo Josef,

verwende eine anderen GPIO. DAs Warndreieck sagt eigentlich immer aus der GPIO hat besondere Funktionen oder Werte beim Start.

Gruß Bison