mqtt2 Readings werden nicht angelegt

[m.lasser@mlpost.de]

Hallo ich Manfred hänge an einem Problem mit Readings die nicht angelegt werden

ich rufe Daten mit mqtt2_client von einer Software ,,Solar-Assistant" ab
Das funkrioniert.
Dann will ich mqtt2_device das Gerät anlegen.
Das funktioniert teilweise, es wird zumindest eine Reading List wie unten aufgeführt angelegt

gw_solar_assistant:SO_AS/total/battery_power/state:.* state
gw_solar_assistant:SO_AS/total/battery_state_of_charge/state:.* state
gw_solar_assistant:SO_AS/total/battery_temperature/state:.* state
gw_solar_assistant:SO_AS/total/bus_voltage/state:.* state
gw_solar_assistant:SO_AS/inverter_1/charger_source_priority/state:.* state
gw_solar_assistant:SO_AS/inverter_1/max_charge_current/state:.* state
gw_solar_assistant:SO_AS/inverter_1/battery_absorption_charge_voltage/state:.* state
gw_solar_assistant:SO_AS/inverter_1/pv_voltage/state:.* state
gw_solar_assistant:SO_AS/inverter_1/grid_frequency/state:.* state
gw_solar_assistant:SO_AS/inverter_1/pv_power/state:.* state
gw_solar_assistant:SO_AS/inverter_1/to_grid_battery_voltage/state:.* state
gw_solar_assistant:SO_AS/inverter_1/battery_voltage/state:.* state
gw_solar_assistant:SO_AS/inverter_1/load_apparent_power/state:.* state
gw_solar_assistant:SO_AS/inverter_1/temperature/state:.* state
gw_solar_assistant:SO_AS/inverter_1/load_percentage/state:.* state
gw_solar_assistant:SO_AS/inverter_1/battery_float_charge_voltage/state:.* state
gw_solar_assistant:SO_AS/inverter_1/max_grid_charge_current/state:.* state
gw_solar_assistant:SO_AS/inverter_1/battery_current/state:.* state
gw_solar_assistant:SO_AS/inverter_1/output_source_priority/state:.* state
gw_solar_assistant:SO_AS/inverter_1/grid_power/state:.* state
gw_solar_assistant:SO_AS/inverter_1/shutdown_battery_voltage/state:.* state
gw_solar_assistant:SO_AS/inverter_1/device_mode/state:.* state
gw_solar_assistant:SO_AS/inverter_1/grid_voltage/state:.* state
gw_solar_assistant:SO_AS/inverter_1/ac_output_frequency/state:.* state
gw_solar_assistant:SO_AS/inverter_1/pv_current/state:.* state
gw_solar_assistant:SO_AS/inverter_1/back_to_battery_voltage/state:.* state
gw_solar_assistant:SO_AS/inverter_1/ac_output_voltage/state:.* state
gw_solar_assistant:SO_AS/inverter_1/load_power/state:.* state
gw_solar_assistant:SO_AS/battery_1/current/state:.* state
gw_solar_assistant:SO_AS/battery_1/cycles/state:.* state
gw_solar_assistant:SO_AS/battery_1/power/state:.* state
gw_solar_assistant:SO_AS/battery_1/state_of_charge/state:.* state
gw_solar_assistant:SO_AS/battery_1/temperature/state:.* state
gw_solar_assistant:SO_AS/battery_1/voltage/state:.* state
gw_solar_assistant:SO_AS/total/battery_energy_in/state:.* state
gw_solar_assistant:SO_AS/total/battery_energy_out/state:.* state
gw_solar_assistant:SO_AS/total/grid_energy_in/state:.* state
gw_solar_assistant:SO_AS/total/grid_energy_out/state:.* state
gw_solar_assistant:SO_AS/total/load_energy/state:.* state
gw_solar_assistant:SO_AS/total/pv_energy/state:.* state

Nur als Readings werden nur die beiden Zeilen angelegt
und alle einzeldaten abwechselt unter state ausgegeben, das heiß unter state steht in schnellen Abständen immer andere Zahlen


IODev gw_solar_assistant 2023-02-14 19:46:05
state 48.0

[LuckyDay]

sieht lustig aus

Code Auswählen Erweitern

gw_solar_assistant:SO_AS/total/battery_power/state:.* state
gw_solar_assistant:SO_AS/total/battery_state_of_charge/state:.* state
gw_solar_assistant:SO_AS/total/battery_temperature/state:.* state

die musst du von Hand abändern

Code Auswählen Erweitern

gw_solar_assistant:SO_AS/total/battery_power/state:.* battery_power
gw_solar_assistant:SO_AS/total/battery_state_of_charge/state:.* battery_state_of_charge
gw_solar_assistant:SO_AS/total/battery_temperature/state:.* battery_temperature

usw.
Ich denke du siehst den Unterschied
das letzte ist oder wird immer der Name des Readings

[m.lasser@mlpost.de]

OK Superm danke es funktioniert

[werner.manz@gmx.de]

Hallo zusammen,
ich habe mir seit gestern auch die Software "solar assistant" gegönnt und wollte natürlich gleich die Messwerte der Wechselrichter ins FHEM tracken. Kann mit bitte mal jemand einen Tipp geben, wie ich den MQTT2_Client richtig anlegen kann? Was muss ich im Solar Assistant eingeben? Was in fhem? Vielen Dank im voraus für euren Support!

Grüße vom Bodensee

Werner