CCU3 und FHEM???

wowogiengen · 04 November 2025, 17:33:25

Hallo,
ich habe versucht, alles wie in https://wiki.fhem.de/wiki/HMCCU beschrieben, umzusetzen.

Ich bekomme wohl eine Verbindung zur CCU3, aber das Erzeugen von Devices in FHEM scheitert
mit einer nichtssagenden Fehlermeldung:

Code Auswählen

get d_ccu createDev HmIPThermostatBuero

Code Auswählen

Results of create command:
Not detected CCU devices: 
  HmIPThermostatBuero = 00392409930634 [HmIPThermostatBuero]

In Log steht noch:

Code Auswählen

2025.11.04 17:30:44 5: HMCCU [d_ccu] No roles detected for device 00392409930634

Code Auswählen

defmod d_ccu HMCCU 192.168.188.190
attr d_ccu ccudef-attributes room=Homematic
attr d_ccu room Homematic
attr d_ccu rpcinterfaces VirtualDevices,BidCos-RF,HmIP-RF
attr d_ccu stateFormat rpcstate/state
attr d_ccu verbose 5

setstate d_ccu running/OK
setstate d_ccu 2025-11-04 17:18:50 PLATFORM rpi3
setstate d_ccu 2025-11-04 17:18:50 PRODUCT ccu3
setstate d_ccu 2025-11-04 17:18:50 VERSION 3.83.6
setstate d_ccu 2025-11-04 17:18:50 count_channels 111
setstate d_ccu 2025-11-04 17:18:50 count_devices 4
setstate d_ccu 2025-11-04 17:18:50 count_groups 0
setstate d_ccu 2025-11-04 17:18:50 count_interfaces 3
setstate d_ccu 2025-11-04 17:18:50 count_programs 1
setstate d_ccu 2025-11-04 17:18:47 rpcstate running
setstate d_ccu 2025-11-04 17:23:32 state OK

Das Gerät HmIPThermostatBuero ist in der CCU3 aktiv, und funktioniert auch soweit.

Wo kann ich noch schauen, wieso es nicht geht?

wowogiengen · 04 November 2025, 22:52:35

Hallo,
nachdem zwischenzeitlich der RPC-Server sich nicht mehr starten lies,
hier noch ein paar Logzeilen, nach dem Neustart des FHEM und dem Befehl

Code Auswählen

set d_ccu on

Code Auswählen

2025.11.04 22:39:21 1: PERL WARNING: Subroutine myUtils_Initialize redefined at ./FHEM/99_myUtilsTemplate.pm line 14.
2025.11.04 22:39:21 1: PERL WARNING: Subroutine SplitReading redefined at ./FHEM/99_myUtilsTemplate.pm line 19.

Die obigen Zeilen gehören nicht zum Problem, aber wo befindet sich die andere Definition? Ich habe alle Dateien durchsucht und nichts gefunden...

Hier jetzt das Log vom HMCCU-Device d_ccu:

Code Auswählen


2025.11.04 22:39:30 1: HMCCU [d_ccu] CCU port 8181 is reachable
2025.11.04 22:39:30 1: HMCCU [d_ccu] Initialized version 2024-12
2025.11.04 22:39:30 1: HMCCU [d_ccu] Initializing device
2025.11.04 22:39:30 1: HMCCU [d_ccu] Read 4 devices with 111 channels, 3 programs, 0 virtual groups from CCU 192.168.188.190
2025.11.04 22:39:31 0: HMCCU [d_ccu] Scheduling post FHEM initialization tasks in 12 seconds

2025.11.04 22:39:31 0: Featurelevel: 6.4
2025.11.04 22:39:31 0: Server started with 214 defined entities (fhem.pl:30177/2025-08-06 perl:5.036000 os:linux user:fhem pid:12938)

2025.11.04 22:39:43 1: HMCCU [d_ccu] Reading device config from CCU. This may take a couple of seconds ...
2025.11.04 22:39:43 1: HMCCU [d_ccu] No RPC device defined for interface BidCos-RF
2025.11.04 22:39:43 1: HMCCU [d_ccu] Creating new RPC device d_rpc188190BidCos_RF for interface BidCos-RF
2025.11.04 22:39:43 1: HMCCURPCPROC [d_rpc188190BidCos_RF] Initialized version 2024-12 for interface BidCos-RF with I/O device d_ccu
2025.11.04 22:39:44 1: HMCCU [d_ccu] No RPC device defined for interface HmIP-RF
2025.11.04 22:39:44 1: HMCCU [d_ccu] Creating new RPC device d_rpc188190HmIP_RF for interface HmIP-RF
2025.11.04 22:39:44 1: HMCCURPCPROC [d_rpc188190HmIP_RF] Initialized version 2024-12 for interface HmIP-RF with I/O device d_ccu
2025.11.04 22:40:17 2: HMCCURPCPROC [d_rpc188190HmIP_RF] RPC request getParamsetDescription failed: RPC::XML::Client::simple_request: 
no element found at line 1, column 0, byte -1:
3^
68599071360
 at /usr/share/perl5/RPC/XML/Client.pm line 436.

2025.11.04 22:40:17 2: HMCCURPCPROC [d_rpc188190HmIP_RF] Retrying request getParamsetDescription
2025.11.04 22:40:47 2: HMCCURPCPROC [d_rpc188190HmIP_RF] RPC request getParamsetDescription failed: RPC::XML::Client::simple_request: 
no element found at line 1, column 0, byte -1:
3^
68599071360
 at /usr/share/perl5/RPC/XML/Client.pm line 436.

2025.11.04 22:40:47 2: HMCCURPCPROC [d_rpc188190HmIP_RF] Retrying request getParamsetDescription
2025.11.04 22:40:47 2: HMCCURPCPROC [d_rpc188190HmIP_RF] Error(s) while fetching parameter set descriptions 00392409930634. Error while executing RPC multicall request: RPC request getParamsetDescription failed: RPC::XML::Client::simple_request: 
no element found at line 1, column 0, byte -1:
3^
68599071360
 at /usr/share/perl5/RPC/XML/Client.pm line 436.

2025.11.04 22:40:47 1: HMCCU [d_ccu] No RPC device defined for interface VirtualDevices
2025.11.04 22:40:47 1: HMCCU [d_ccu] Creating new RPC device d_rpc188190VirtualDevices for interface VirtualDevices
2025.11.04 22:40:47 1: HMCCURPCPROC [d_rpc188190VirtualDevices] Initialized version 2024-12 for interface VirtualDevices with I/O device d_ccu

Die "raw definition":

Code Auswählen

defmod d_ccu HMCCU 192.168.188.190
attr d_ccu room Homematic
attr d_ccu stateFormat rpcstate/state

setstate d_ccu inactive/OK
setstate d_ccu 2025-11-04 22:39:30 PLATFORM rpi3
setstate d_ccu 2025-11-04 22:39:30 PRODUCT ccu3
setstate d_ccu 2025-11-04 22:39:30 VERSION 3.83.6
setstate d_ccu 2025-11-04 22:39:30 count_channels 111
setstate d_ccu 2025-11-04 22:39:30 count_devices 4
setstate d_ccu 2025-11-04 22:39:30 count_groups 0
setstate d_ccu 2025-11-04 22:39:30 count_interfaces 3
setstate d_ccu 2025-11-04 22:39:30 count_programs 3
setstate d_ccu 2025-11-04 22:39:30 rpcstate inactive
setstate d_ccu 2025-11-04 22:39:43 state OK

das define ist einfach:

Code Auswählen

define d_ccu HMCCU 192.168.188.190

Im Anhang das komplette list des devices...

Ich hoffe, mir kann jemand erklären, wieso ich das Thermostat nicht als Device in FHEM bekomme...
Oder was ich eingeben muss, um es manuell einzubinden...

Viele Grüße
Wolfgang

wowogiengen · 04 November 2025, 23:45:55

Habe das Device jetzt manuell erzeugt.
Aber wie hier angegeben:

ich versuche nun den statedatapoint zu setzen:

Code Auswählen

attr HmIPThermostatBuero statadatapoint 1.ACTUAL_TEMPERATURE
Laut

Code Auswählen

get HmIPThermostatBuero deviceInfo

Code Auswählen

Device channels and datapoints

DEV HmIPThermostatBuero 00392409930634 interface=HmIP-RF type=HmIP-WTH-1
CHN 00392409930634:0 HmIPThermostatBuero:0
   0.CONFIG_PENDING = false {b} [RE]
   0.DUTY_CYCLE = false {b} [RE]
   0.INSTALL_TEST = true {b} [RW]
   0.LOW_BAT = false {b} [RE]
   0.OPERATING_VOLTAGE = 3.100000 {f} [RE]
   0.OPERATING_VOLTAGE_STATUS = 0 {i} [RE]
   0.RSSI_DEVICE = -45 {i} [RE]
   0.RSSI_PEER = -46 {i} [RE]
   0.UNREACH = false {b} [RE]
   0.UPDATE_PENDING = false {b} [RE]
CHN 00392409930634:1 HmIP-WTH-1 00392409930634:1
   1.ACTIVE_PROFILE = 1 {i} [RWE]
   1.ACTUAL_TEMPERATURE = 22.200000 {f} [RE]
   1.ACTUAL_TEMPERATURE_STATUS = 0 {i} [RE]
   1.BOOST_MODE = false {b} [WE]
   1.BOOST_TIME = 0 {i} [RE]
   1.CONTROL_DIFFERENTIAL_TEMPERATURE =  {f} [W]
   1.CONTROL_MODE =  {i} [W]
   1.DURATION_UNIT =  {i} [W]
   1.DURATION_VALUE =  {i} [W]
   1.FROST_PROTECTION = false {b} [RE]
   1.HEATING_COOLING = 0 {i} [RWE]
   1.HUMIDITY = 52 {i} [RE]
   1.HUMIDITY_STATUS = 0 {i} [RE]
   1.PARTY_MODE = false {b} [RE]
   1.PARTY_SET_POINT_TEMPERATURE = 0.000000 {f} [RE]
   1.PARTY_TIME_END =  {s} [RWE]
   1.PARTY_TIME_START =  {s} [RWE]
   1.QUICK_VETO_TIME = 0 {i} [RE]
   1.SET_POINT_MODE = 1 {i} [RWE]
   1.SET_POINT_TEMPERATURE = 20.500000 {f} [RWE]
   1.SWITCH_POINT_OCCURED = false {b} [RE]
   1.WINDOW_STATE = 0 {i} [RWE]

Device description

Device 00392409930634 HmIPThermostatBuero [HmIP-WTH-1]
  AES_ACTIVE: 1
  AVAILABLE_FIRMWARE: 0.0.0
  CHILDREN: 00392409930634:0,00392409930634:1,00392409930634:2,00392409930634:3,00392409930634:4,00392409930634:5,00392409930634:6,00392409930634:7
  DIRECTION: NONE
  FIRMWARE: 1.2.8
  FIRMWARE_UPDATE_STATE: UP_TO_DATE
  FLAGS: Visible
  PARAMSETS: MASTER,SERVICE
  RF_ADDRESS: 6110729
  ROAMING: 0
  RX_MODE: ALWAYS,LAZY_CONFIG,BURST
  SUBTYPE: WTH-2
  UPDATABLE: 1
Channel 00392409930634:0 HmIPThermostatBuero:0 [MAINTENANCE]
  AES_ACTIVE: 1
  DIRECTION: NONE
  FLAGS: Visible
  PARAMSETS: MASTER,VALUES,SERVICE
  PARENT: 00392409930634
  PARENT_TYPE: HmIP-WTH-1
  RF_ADDRESS: 0
  ROAMING: 0
  RX_MODE: 
  UPDATABLE: 1
Channel 00392409930634:1 HmIP-WTH-1 00392409930634:1 [HEATING_CLIMATECONTROL_TRANSCEIVER] known
  AES_ACTIVE: 1
  DIRECTION: SENDER
  FLAGS: Visible
  LINK_SOURCE_ROLES: CLIMATE_CONTROL_WTH_TRV
  PARAMSETS: MASTER,VALUES,LINK,SERVICE
  PARENT: 00392409930634
  PARENT_TYPE: HmIP-WTH-1
  RF_ADDRESS: 0
  ROAMING: 0
  RX_MODE: 
  UPDATABLE: 1
Channel 00392409930634:2 HmIP-WTH-1 00392409930634:2 [HEATING_CLIMATECONTROL_RECEIVER]
  AES_ACTIVE: 1
  DIRECTION: RECEIVER
  FLAGS: Visible
  LINK_TARGET_ROLES: CLIMATE_CONTROL_WGD_WTH,CLIMATE_CONTROL_TRV_WTH
  PARAMSETS: MASTER,VALUES,LINK,SERVICE
  PARENT: 00392409930634
  PARENT_TYPE: HmIP-WTH-1
  RF_ADDRESS: 0
  ROAMING: 0
  RX_MODE: 
  UPDATABLE: 1
Channel 00392409930634:3 HmIP-WTH-1 00392409930634:3 [HEATING_CLIMATECONTROL_CL_TRANSMITTER]
  AES_ACTIVE: 1
  DIRECTION: SENDER
  FLAGS: Visible
  LINK_SOURCE_ROLES: CLIMATE_CONTROL_CL
  PARAMSETS: MASTER,VALUES,LINK,SERVICE
  PARENT: 00392409930634
  PARENT_TYPE: HmIP-WTH-1
  RF_ADDRESS: 0
  ROAMING: 0
  RX_MODE: 
  UPDATABLE: 1
Channel 00392409930634:4 HmIP-WTH-1 00392409930634:4 [HEATING_SHUTTER_CONTACT_RECEIVER]
  AES_ACTIVE: 1
  DIRECTION: RECEIVER
  FLAGS: Visible
  LINK_TARGET_ROLES: WINDOW_SWITCH
  PARAMSETS: MASTER,VALUES,LINK,SERVICE
  PARENT: 00392409930634
  PARENT_TYPE: HmIP-WTH-1
  RF_ADDRESS: 0
  ROAMING: 0
  RX_MODE: 
  UPDATABLE: 1
Channel 00392409930634:5 HmIP-WTH-1 00392409930634:5 [HEATING_CLIMATECONTROL_SWITCH_TRANSMITTER]
  AES_ACTIVE: 1
  DIRECTION: SENDER
  FLAGS: Visible
  LINK_SOURCE_ROLES: SWITCH
  PARAMSETS: MASTER,VALUES,LINK,SERVICE
  PARENT: 00392409930634
  PARENT_TYPE: HmIP-WTH-1
  RF_ADDRESS: 0
  ROAMING: 0
  RX_MODE: 
  UPDATABLE: 1
Channel 00392409930634:6 HmIP-WTH-1 00392409930634:6 [HEATING_KEY_RECEIVER]
  AES_ACTIVE: 1
  DIRECTION: RECEIVER
  FLAGS: Visible
  LINK_TARGET_ROLES: REMOTE_CONTROL
  PARAMSETS: MASTER,VALUES,LINK,SERVICE
  PARENT: 00392409930634
  PARENT_TYPE: HmIP-WTH-1
  RF_ADDRESS: 0
  ROAMING: 0
  RX_MODE: 
  UPDATABLE: 1
Channel 00392409930634:7 HmIP-WTH-1 00392409930634:7 [CLIMATECONTROL_FLOOR_TRANSMITTER]
  AES_ACTIVE: 1
  DIRECTION: SENDER
  FLAGS: Visible
  LINK_SOURCE_ROLES: CLIMATE_CONTROL_FLOOR
  PARAMSETS: MASTER,VALUES,LINK,SERVICE
  PARENT: 00392409930634
  PARENT_TYPE: HmIP-WTH-1
  RF_ADDRESS: 0
  ROAMING: 0
  RX_MODE: 
  UPDATABLE: 1

Defaults

Support for role(s) HEATING_CLIMATECONTROL_TRANSCEIVER of device type HmIP-WTH-1 is built in.

Sollte das ja funktionieren...

JoWiemann · 05 November 2025, 07:24:05

Hallo,

wenn Du:
get <name> ccuConfig
aufrufst, dann werden alle in der CCU3 geladenen Geräte nach Fhem übertragen.

Dann einmal die FhemWeb Seite neu laden und die Geräte stehen in der Liste von:
get <name> createDev
und können ganz einfach in Fhem angelegt werden.

Grüße Jörg

wowogiengen · 05 November 2025, 08:36:22

Zitat von: JoWiemann am 05 November 2025, 07:24:05Hallo,

wenn Du:
get <name> ccuConfig
aufrufst, dann werden alle in der CCU3 geladenen Geräte nach Fhem übertragen.

Dann einmal die FhemWeb Seite neu laden und die Geräte stehen in der Liste von:
get <name> createDev
und können ganz einfach in Fhem angelegt werden.

Grüße Jörg

Hallo,
wenn ich get d_ccu ccuConfig aufrufe, passiert bei mir augenscheinlich nichts.

Ich sehe keine Reaktion...
Laut den Readings habe ich wohl Devices importiert, aber ich sehe sie nicht,
wenn ich get d_ccu createDev auswähle. Bei mir wird nichts angezeigt.

Irgendwo ist da der Wurm drin...

Beim manuellen Anlegen des Devices funktioniert zwar die Datenübernahme aus CCU3,
aber ich kann die Datenpunkte nicht im Attribut eingeben.

passibe · 05 November 2025, 08:58:35

Zitat von: wowogiengen am 04 November 2025, 22:52:35RPC request getParamsetDescription failed: RPC::XML::Client::simple_request:
no element found at line 1, column 0, byte -1:
3^
68599071360
at /usr/share/perl5/RPC/XML/Client.pm line 436.

2025.11.04 22:40:17 2: HMCCURPCPROC [d_rpc188190HmIP_RF] Retrying request getParamsetDescription
2025.11.04 22:40:47 2: HMCCURPCPROC [d_rpc188190HmIP_RF] RPC request getParamsetDescription failed: RPC::XML::Client::simple_request:
no element found at line 1, column 0, byte -1:
3^
68599071360
at /usr/share/perl5/RPC/XML/Client.pm line 436.

2025.11.04 22:40:47 2: HMCCURPCPROC [d_rpc188190HmIP_RF] Retrying request getParamsetDescription
2025.11.04 22:40:47 2: HMCCURPCPROC [d_rpc188190HmIP_RF] Error(s) while fetching parameter set descriptions 00392409930634. Error while executing RPC multicall request: RPC request getParamsetDescription failed: RPC::XML::Client::simple_request:
no element found at line 1, column 0, byte -1:
3^
68599071360
at /usr/share/perl5/RPC/XML/Client.pm line 436.

Also diese ganzen Fehlermeldungen sehen nicht gesund aus.

Oben hattest du ja noch ein running/OK bei den Readings rpcstate/state in d_ccu. Ist das immer noch so?

Poste vielleicht auch mal ein list von d_rpc188190HmIP_RF

wowogiengen · 05 November 2025, 09:32:53

Hallo,
hier das list von d_rpc188190HmIP_RF

Code Auswählen

Internals:
   CCUNum     1
   DEF        http://192.168.188.190 HmIP-RF
   FD         27
   FUUID      690a72a0-f33f-a625-2784-15f9871c294fb1ab
   IODev      d_ccu
   NAME       d_rpc188190HmIP_RF
   NR         244
   RPCPID     13661
   RPCState   running
   STATE      running/OK
   TYPE       HMCCURPCPROC
   callback   192.168.188.10:7420
   ccuip      192.168.188.190
   ccustate   active
   ccutype    CCU2/3
   eventCount 22
   host       192.168.188.190
   prot       http
   rpcid      188010188190
   rpcinterface HmIP-RF
   rpcip      192.168.188.190
   rpcport    2010
   version    2024-12
   READINGS:
     2025-11-04 22:57:13   rpcstate        running
     2025-11-04 22:57:13   state           OK
   hmccu:
     defaultaddr 192.168.188.10
     devspec    HmIP-RF
     evtime     0
     localaddr  192.168.188.10
     rpcstarttime 1762293433.34015
     rpc:
       auth       
       avgdelay   0.27932364796947
       cbport     7420
       cburl      http://192.168.188.10:7420/fh2010
       clkey      CB2010188010188190
       clurl      
       evtime     1762330931.72262
       methods    getLinkPeers,getParamset,restoreConfigToDevice,getDeviceDescription,replaceDevice,listReplaceableDevices,setTeam,activateLinkParamset,getKeyMismatchDevice,getParamsetDescription,installFirmware,init,getMetadata,deleteDevice,putParamset,reportValueUsage,changeKey,setBidcosInterface,setTempKey,getSuppressedServiceMessages,abortDeleteDevice,addLink,getLinkInfo,getInstallMode,system.methodHelp,getLinks,ping,setInterfaceClock,listDevices,clearConfigCache,listTeams,setInstallModeWithWhitelist,determineParameter,logLevel,getServiceMessages,setInstallMode,getVersion,system.multicall,searchDevices,updateFirmware,suppressServiceMessages,removeLink,refreshDeployedDeviceFirmwareList,setMetadata,getValue,getParamsetId,setLinkInfo,addDevice,setValue,system.listMethods,listBidcosInterfaces,rssiInfo
       pid        13661
       port       2010
       state      running
       sumdelay   227.090125799179
       rec:
         DD         0
         EV         813
         EX         0
         IN         0
         ND         63
         RA         0
         RD         0
         SL         1
         ST         1
         TO         0
         UD         0
       snd:
         DD         0
         EV         436
         EX         0
         IN         0
         ND         63
         RA         0
         RD         0
         SL         1
         TO         0
         UD         0
Attributes:
   alias      CCU 188190 RPC HmIP-RF
   eventMap   /rpcserver on:on/rpcserver off:off/
   room       Homematic
   stateFormat rpcstate/state
   verbose    2

Und hier die forum-ready-definition von d_rpc188190HmIP_RF:

Code Auswählen

define d_rpc188190HmIP_RF HMCCURPCPROC http://192.168.188.190 HmIP-RF
attr d_rpc188190HmIP_RF alias CCU 188190 RPC HmIP-RF
attr d_rpc188190HmIP_RF eventMap /rpcserver on:on/rpcserver off:off/
attr d_rpc188190HmIP_RF room Homematic
attr d_rpc188190HmIP_RF stateFormat rpcstate/state
attr d_rpc188190HmIP_RF verbose 2
#   CCUNum     1
#   DEF        http://192.168.188.190 HmIP-RF
#   FD         27
#   FUUID      690a72a0-f33f-a625-2784-15f9871c294fb1ab
#   IODev      d_ccu
#   NAME       d_rpc188190HmIP_RF
#   NR         244
#   RPCPID     13661
#   RPCState   running
#   STATE      running/OK
#   TYPE       HMCCURPCPROC
#   callback   192.168.188.10:7420
#   ccuip      192.168.188.190
#   ccustate   active
#   ccutype    CCU2/3
#   eventCount 22
#   host       192.168.188.190
#   prot       http
#   rpcid      188010188190
#   rpcinterface HmIP-RF
#   rpcip      192.168.188.190
#   rpcport    2010
#   version    2024-12
#   READINGS:
#     2025-11-04 22:57:13   rpcstate        running
#     2025-11-04 22:57:13   state           OK
#   hmccu:
#     defaultaddr 192.168.188.10
#     devspec    HmIP-RF
#     evtime     0
#     localaddr  192.168.188.10
#     rpcstarttime 1762293433.34015
#     rpc:
#       auth       
#       avgdelay   0.27932364796947
#       cbport     7420
#       cburl      http://192.168.188.10:7420/fh2010
#       clkey      CB2010188010188190
#       clurl      
#       evtime     1762330931.72262
#       methods    getLinkPeers,getParamset,restoreConfigToDevice,getDeviceDescription,replaceDevice,listReplaceableDevices,setTeam,activateLinkParamset,getKeyMismatchDevice,getParamsetDescription,installFirmware,init,getMetadata,deleteDevice,putParamset,reportValueUsage,changeKey,setBidcosInterface,setTempKey,getSuppressedServiceMessages,abortDeleteDevice,addLink,getLinkInfo,getInstallMode,system.methodHelp,getLinks,ping,setInterfaceClock,listDevices,clearConfigCache,listTeams,setInstallModeWithWhitelist,determineParameter,logLevel,getServiceMessages,setInstallMode,getVersion,system.multicall,searchDevices,updateFirmware,suppressServiceMessages,removeLink,refreshDeployedDeviceFirmwareList,setMetadata,getValue,getParamsetId,setLinkInfo,addDevice,setValue,system.listMethods,listBidcosInterfaces,rssiInfo
#       pid        13661
#       port       2010
#       state      running
#       sumdelay   227.090125799179
#       rec:
#         DD         0
#         EV         813
#         EX         0
#         IN         0
#         ND         63
#         RA         0
#         RD         0
#         SL         1
#         ST         1
#         TO         0
#         UD         0
#       snd:
#         DD         0
#         EV         436
#         EX         0
#         IN         0
#         ND         63
#         RA         0
#         RD         0
#         SL         1
#         TO         0
#         UD         0
#
setstate d_rpc188190HmIP_RF running/OK
setstate d_rpc188190HmIP_RF 2025-11-04 22:57:13 rpcstate running
setstate d_rpc188190HmIP_RF 2025-11-04 22:57:13 state OK

das list der d_ccu hatte ich ja bereits gepostet...

Ich werde heute mal meinen Laptop neu aufsetzen, mit Linux und FHEM, so dass ich ein Testsystem habe,
um zu sehen, ob meine rpi-Installation einen Schuss hat...

Viele Grüße
Wolfgang

wowogiengen · 05 November 2025, 13:21:35

Habe jetzt FHEM auf dem Laptop endlich zum Laufen bekommen,
nachdem ich mir einiges habe aus den Fingern saugen müssen, damit FHEM überhaupt mal läuft...

Das Bild zeigt mir, dass HMCCU die Devices sehr wohl kennt...

Du darfst diesen Dateianhang nicht ansehen.
Aber auch nach einem Neuladen der Seite kann ich keine Devices im Dropdown sehen...

Ich vermute mal, dass sich die API zur CCU geändert hat...

Sollte ich jetzt viel Geld für die CCU3 ausgegeben haben, und kann sie nicht mal mit FHEM benutzen?