[73_AutoShuttersControl.pm] Rolllos automatisiert steuern - Version 0.8.x

Begonnen von CoolTux, 15 November 2019, 12:51:08

Vorheriges Thema - Nächstes Thema
Drucken
Nach unten Seiten 1 ... 112 113 114 115 116 ... 148
Benutzer-Aktionen

CoolTux

#1695
03 Mai 2020, 15:51:35
Das einzige was mit auf fällt ist das das Reading ASC_ShuttersLastDrive im Rollo fehlt.
Kannst du bitte Debug aktivieren
Du musst nicht wissen wie es geht! Du musst nur wissen wo es steht, wie es geht.
Support me to buy new test hardware for development: https://www.paypal.com/paypalme/MOldenburg
My FHEM Git: https://git.cooltux.net/FHEM/
Das TuxNet Wiki:
https://www.cooltux.net

Dreggwatz

#1696
03 Mai 2020, 16:12:10
Hab ich jetzt aktiviert, wo finde ich den Log? In meine normale Logfile erscheint nichts von ASC

CoolTux

#1697
03 Mai 2020, 16:42:55
Zitat von: Dreggwatz am 03 Mai 2020, 16:12:10
Hab ich jetzt aktiviert, wo finde ich den Log? In meine normale Logfile erscheint nichts von ASC

Wie hast du es denn aktiviert? Zeig mal bitte das list vom ASC Device. Logeinträge sollten im FHEM Log stehen.
Du musst nicht wissen wie es geht! Du musst nur wissen wo es steht, wie es geht.
Support me to buy new test hardware for development: https://www.paypal.com/paypalme/MOldenburg
My FHEM Git: https://git.cooltux.net/FHEM/
Das TuxNet Wiki:
https://www.cooltux.net

Dreggwatz

#1698
03 Mai 2020, 17:15:23 Letzte Bearbeitung: 03 Mai 2020, 17:17:43 von Dreggwatz
hab bei Attr ASC_Debug auf 1

Code Auswählen
Internals:
   FUUID      5ea72722-f33f-8381-14ac-dd34b09229831593
   FVERSION   73_AutoShuttersControl.pm:v0.8.27-s21670/2020-04-14 TESTING
   MID        da39a3ee5e6b4b0d3255bfef95601890afd80709
   NAME       myASControl
   NOTIFYDEV  global,myASControl,Rol.EG_SZ1,Rol.EG_SZ2,SB.Dach,myTL,Rol.EG_SZ2,Rol.EG_SZ1
   NR         104
   NTFY_ORDER 51-myASControl
   STATE      created new drive timer
   TYPE       AutoShuttersControl
   VERSION    v0.8.27
   OLDREADINGS:
   READINGS:
     2020-05-03 09:00:02   Rol.EG_SZ1_lastPosValue 100
     2020-05-03 09:00:02   Rol.EG_SZ1_nextAstroTimeEvent  3.05.2020 - 21:00
     2020-05-03 09:00:02   Rol.EG_SZ2_lastPosValue 100
     2020-05-03 09:00:02   Rol.EG_SZ2_nextAstroTimeEvent  3.05.2020 - 21:00
     2020-04-27 20:40:34   ascEnable       on
     2020-04-27 20:47:44   controlShading  on
     2020-04-27 20:40:34   hardLockOut     off
     2020-04-30 23:13:49   partyMode       on
     2020-05-01 15:53:41   room_Haus       Rol.EG_SZ1,Rol.EG_SZ2
     2020-04-27 20:40:34   selfDefense     off
     2020-05-03 14:39:11   state           created new drive timer
     2020-04-30 23:15:02   sunriseTimeWeHoliday on
     2020-05-01 15:53:41   userAttrList    rolled out
   helper:
     shuttersList:
       Rol.EG_SZ1
       Rol.EG_SZ2
   monitoredDevs:
     Rol.EG_SZ1:
     Rol.EG_SZ2:
     SB.Dach:
       Rol.EG_SZ1 ASC_BrightnessSensor
     myTL:
       myASControl ASC_twilightDevice
Attributes:
   ASC_autoAstroModeEvening ASTRONOMIC
   ASC_autoAstroModeMorning ASTRONOMIC
   ASC_autoShuttersControlComfort on
   ASC_autoShuttersControlEvening on
   ASC_autoShuttersControlMorning on
   ASC_debug  1
   ASC_shuttersDriveDelay 0
   ASC_tempSensor Wetter.Weyer
   ASC_twilightDevice myTL
   alias      myASControl
   devStateIcon { AutoShuttersControl_DevStateIcon($name) }
   group      Rolladen
   icon       fts_shutter_automatic
   room       Haus

das versteh ich nicht:
Code Auswählen
monitoredDevs:
     Rol.EG_SZ1:
     Rol.EG_SZ2:
     SB.Dach:
       Rol.EG_SZ1 ASC_BrightnessSensor
     myTL:
       myASControl ASC_twilightDevice

CoolTux

#1699
03 Mai 2020, 18:00:56
Du hast einen Brightness Sensor für das Dachrollo definiert.
Du musst nicht wissen wie es geht! Du musst nur wissen wo es steht, wie es geht.
Support me to buy new test hardware for development: https://www.paypal.com/paypalme/MOldenburg
My FHEM Git: https://git.cooltux.net/FHEM/
Das TuxNet Wiki:
https://www.cooltux.net

Dreggwatz

#1700
03 Mai 2020, 18:11:35 Letzte Bearbeitung: 03 Mai 2020, 18:20:18 von Dreggwatz
SB.Dach ist mein Brightness Sensor  :o, muss ich mal gucken

...

Im Rolladen ist es richtig zugewiesen:
Code Auswählen
Internals:
   DEF        10.0.0.212
   DURATION   0
   FUUID      5ea33ec1-f33f-8381-7583-eae06a7f21afd5bb
   INTERVAL   60
   MOVING     stopped
   NAME       Rol.EG_SZ1
   NR         102
   STATE      stopped
   TARGETPCT  0
   TCPIP      10.0.0.212
   TYPE       Shelly
   OLDREADINGS:
   READINGS:
     2020-04-27 20:43:41   ASC_Enable      on
     2020-05-03 14:39:11   ASC_Time_DriveDown  3.05.2020 - 21:00
     2020-05-03 14:39:11   ASC_Time_DriveUp  4.05.2020 - 07:15
     2020-05-03 14:39:11   ASC_Time_PrivacyDriveUp  4.05.2020 - 07:00
     2020-05-01 15:53:41   associatedWith  myASControl
     2020-04-24 21:32:18   cloud           enabled(connected)
     2020-04-25 07:45:39   config          rc= [channel r]
     2020-04-24 21:32:18   firmware        v1.6.0
     2020-05-02 23:14:29   last_dir        up
     2020-05-01 15:53:39   network         connected to 10.0.0.212
     2020-05-03 08:18:40   pct             100
     2020-05-03 08:18:40   position        open
     2020-05-03 17:58:32   power           0
     2020-05-03 08:18:40   state           stopped
     2020-04-24 21:34:18   stop_reason     normal
Attributes:
   ASC        2
   ASC_Adv    on
   ASC_AutoAstroModeEvening ASTRONOMIC
   ASC_AutoAstroModeMorning ASTRONOMIC
   ASC_BlockingTime_afterManual 1200
   ASC_BlockingTime_beforDayOpen 3600
   ASC_BlockingTime_beforNightClose 3600
   ASC_BrightnessSensor SB.Dach
   ASC_Closed_Pos 0
   ASC_Down   astro
   ASC_DriveUpMaxDuration 20
   ASC_Drive_Delay 0
   ASC_Mode_Down always
   ASC_Mode_Up always
   ASC_Open_Pos 100
   ASC_Partymode off
   ASC_Pos_Reading pct
   ASC_PrivacyUpValue_beforeDayOpen 895
   ASC_PrivacyUp_Pos 20
   ASC_Shading_InOutAzimuth 140:290
   ASC_Shading_MinMax_Elevation 20:100
   ASC_Shading_Min_OutsideTemperature 10
   ASC_Shading_Mode always
   ASC_Shading_Pos 30
   ASC_Shading_StateChange_SunnyCloudy 50000:30000
   ASC_Shading_WaitingPeriod 300
   ASC_Time_Down_Early 16:30
   ASC_Time_Down_Late 21:30
   ASC_Time_Up_Early 7:15
   ASC_Time_Up_Late 8:00
   ASC_Time_Up_WE_Holiday 9:00
   ASC_Up     astro
   alias      Rol.EG_SZ1
   cmdIcon    open:fts_shutter_up closed:fts_shutter_down stop:fts_shutter_manual
   devStateIcon open:fts_shutter_10:closed closed:fts_shutter_100:open half:fts_shutter_50:closed drive-up:fts_shutter_up@red:stop drive-down:fts_shutter_down@red:stop pct-100:fts_shutter_100:open pct-90:fts_shutter_80:closed pct-80:fts_shutter_80:closed pct-70:fts_shutter_70:closed pct-60:fts_shutter_60:closed pct-50:fts_shutter_50:closed pct-40:fts_shutter_40:open pct-30:fts_shutter_30:open pct-20:fts_shutter_20:open pct-10:fts_shutter_10:open pct-0:fts_shutter_10:closed
   event-on-change-reading state
   group      Rolladen
   icon       fts_shutter_automatic
   mode       roller
   model      shelly2.5
   room       Haus
   userattr   ASC_Adv:on,off ASC_Antifreeze:off,soft,hard,am,pm ASC_Antifreeze_Pos:5,10,15,20,25,30,35,40,45,50,55,60,65,70,75,80,85,90,95,100 ASC_AutoAstroModeEvening:REAL,CIVIL,NAUTIC,ASTRONOMIC,HORIZON ASC_AutoAstroModeEveningHorizon:-9,-8,-7,-6,-5,-4,-3,-2,-1,0,1,2,3,4,5,6,7,8,9 ASC_AutoAstroModeMorning:REAL,CIVIL,NAUTIC,ASTRONOMIC,HORIZON ASC_AutoAstroModeMorningHorizon:-9,-8,-7,-6,-5,-4,-3,-2,-1,0,1,2,3,4,5,6,7,8,9 ASC_BlockingTime_afterManual ASC_BlockingTime_beforDayOpen ASC_BlockingTime_beforNightClose ASC_BrightnessSensor ASC_Closed_Pos:0,10,20,30,40,50,60,70,80,90,100 ASC_ComfortOpen_Pos:0,10,20,30,40,50,60,70,80,90,100 ASC_Down:time,astro,brightness,roommate ASC_DriveUpMaxDuration ASC_Drive_Delay ASC_Drive_DelayStart ASC_ExternalTrigger ASC_GuestRoom:on,off ASC_LockOut:soft,hard,off ASC_LockOut_Cmd:inhibit,blocked,protection ASC_Mode_Down:absent,always,off,home ASC_Mode_Up:absent,always,off,home ASC_Open_Pos:0,10,20,30,40,50,60,70,80,90,100 ASC_Partymode:on,off ASC_Pos_Reading ASC_PrivacyDownValue_beforeNightClose ASC_PrivacyDown_Pos ASC_PrivacyUpValue_beforeDayOpen ASC_PrivacyUp_Pos ASC_RainProtection:on,off ASC_Roommate_Device ASC_Roommate_Reading ASC_Self_Defense_AbsentDelay ASC_Self_Defense_Mode:absent,gone,off ASC_Shading_InOutAzimuth ASC_Shading_MinMax_Elevation ASC_Shading_Min_OutsideTemperature ASC_Shading_Mode:absent,always,off,home ASC_Shading_Pos:10,20,30,40,50,60,70,80,90,100 ASC_Shading_StateChange_SunnyCloudy ASC_Shading_WaitingPeriod ASC_Shutter_IdleDetection ASC_ShuttersPlace:window,terrace ASC_Sleep_Pos:0,10,20,30,40,50,60,70,80,90,100 ASC_TempSensor ASC_Time_Down_Early ASC_Time_Down_Late ASC_Time_Up_Early ASC_Time_Up_Late ASC_Time_Up_WE_Holiday ASC_Up:time,astro,brightness,roommate ASC_Ventilate_Pos:10,20,30,40,50,60,70,80,90,100 ASC_Ventilate_Window_Open:on,off ASC_WiggleValue ASC_WindParameters ASC_WindProtection:on,off ASC_WindowRec ASC_WindowRec_PosAfterDayClosed:open,lastManual ASC_WindowRec_subType:twostate,threestate
   webCmd     open:closed:stop:pct

Im ASC Device kann ich unter ATTR gar kein BrighnessSensor angeben...

Hatte im SZ2 den Brightness entfernt gehabt, um zusehen ob einer der beiden fährt. Wenn er wieder drin ist erscheint er im list ASC, ist also OK imho:
Code Auswählen
   monitoredDevs:
     Rol.EG_SZ1:
     Rol.EG_SZ2:
     SB.Dach:
       Rol.EG_SZ1 ASC_BrightnessSensor
       Rol.EG_SZ2 ASC_BrightnessSensor
     myTL:
       myASControl ASC_twilightDevice

Dreggwatz

#1701
03 Mai 2020, 18:23:37
Jetzt hab ich ein LOG:

Code Auswählen
ASC_DEBUG!!! 2020.05. 3 18:16:21 - FnIsDay: Rol.EG_SZ1 Allgemein: 1

ASC_DEBUG!!! 2020.05. 3 18:16:21 - FnIsDay: Rol.EG_SZ1 getDownBrightness: 1 Brightness: 27552.45 BrightnessMin: 500 Sunset: 0

ASC_DEBUG!!! 2020.05. 3 18:16:21 - FnIsDay: Rol.EG_SZ1 getUpBrightness: 1 Brightness: 27552.45 BrightnessMax: 800 Sunrise: 1

ASC_DEBUG!!! 2020.05. 3 18:16:21 - FnIsDay: Rol.EG_SZ2 Allgemein: 1

ASC_DEBUG!!! 2020.05. 3 18:16:21 - FnIsDay: Rol.EG_SZ2 getDownBrightness: 1 Brightness: -1 BrightnessMin: 500 Sunset: 0

ASC_DEBUG!!! 2020.05. 3 18:16:21 - FnIsDay: Rol.EG_SZ2 getUpBrightness: 1 Brightness: -1 BrightnessMax: 800 Sunrise: 1

CoolTux

#1702
03 Mai 2020, 18:38:34
Er kann den Brightness Sensor nicht auslesen. Gib mal das Reading bitte mit und mach dann ein

{ ascAPIget('Brightness','ROLLONAME') }
Du musst nicht wissen wie es geht! Du musst nur wissen wo es steht, wie es geht.
Support me to buy new test hardware for development: https://www.paypal.com/paypalme/MOldenburg
My FHEM Git: https://git.cooltux.net/FHEM/
Das TuxNet Wiki:
https://www.cooltux.net

Dreggwatz

#1703
03 Mai 2020, 18:53:32
Wo setzte ich das Reading genau? Im Rollo unter ASC_BrightnessSensor SB.Dach:brightness?

Log wirft jetzt ein Fehler raus:
Code Auswählen
2020.05.03 18:50:38.833 1:  devspec2array Rol.EG_SZ1,Rol.EG_SZ2,SB.Dach,SB.Dach[,global,myASControl,myTL: Unmatched [ in regex; marked by <-- HERE in m/^(SB.Dach[ <-- HERE )$/ at fhem.pl line 1319.

2020.05.03 18:50:38.833 1:  stacktrace:
2020.05.03 18:50:38.833 1:      main::devspec2array                 called by fhem.pl (5353)
2020.05.03 18:50:38.833 1:      main::createNtfyHash                called by fhem.pl (3692)
2020.05.03 18:50:38.833 1:      main::DoTrigger                     called by fhem.pl (1678)
2020.05.03 18:50:38.833 1:      main::CommandSave                   called by fhem.pl (1243)
2020.05.03 18:50:38.833 1:      main::AnalyzeCommand                called by fhem.pl (1096)
2020.05.03 18:50:38.833 1:      main::AnalyzeCommandChain           called by ./FHEM/01_FHEMWEB.pm (2711)
2020.05.03 18:50:38.833 1:      main::FW_fC                         called by ./FHEM/01_FHEMWEB.pm (938)
2020.05.03 18:50:38.833 1:      main::FW_answerCall                 called by ./FHEM/01_FHEMWEB.pm (590)
2020.05.03 18:50:38.834 1:      main::FW_Read                       called by fhem.pl (3777)
2020.05.03 18:50:38.834 1:      main::CallFn                        called by fhem.pl (753)

CoolTux

#1704
03 Mai 2020, 19:00:04
Ja genau so. Und setze expert mal auf 1 und mache dann ein set createNewNotifyDev
Du musst nicht wissen wie es geht! Du musst nur wissen wo es steht, wie es geht.
Support me to buy new test hardware for development: https://www.paypal.com/paypalme/MOldenburg
My FHEM Git: https://git.cooltux.net/FHEM/
Das TuxNet Wiki:
https://www.cooltux.net

Dreggwatz

#1705
03 Mai 2020, 19:16:55 Letzte Bearbeitung: 03 Mai 2020, 19:20:19 von Dreggwatz
{ ascAPIget('Brightness','ROLLONAME') }
gibt -1

set createNewNotifyDev
gibt Please define createNewNotifyDev first

Rollo:
Code Auswählen
Internals:
   DEF        10.0.0.212
   DURATION   0
   FUUID      5ea33ec1-f33f-8381-7583-eae06a7f21afd5bb
   INTERVAL   60
   MOVING     stopped
   NAME       Rol.EG_SZ1
   NR         100
   STATE      stopped
   TCPIP      10.0.0.212
   TYPE       Shelly
   READINGS:
     2020-04-27 20:43:41   ASC_Enable      on
     2020-05-03 18:16:24   ASC_Time_DriveDown 3.05.2020 - 21:00
     2020-05-03 18:16:24   ASC_Time_DriveUp 4.05.2020 - 07:15
     2020-05-03 18:16:24   ASC_Time_PrivacyDriveUp 4.05.2020 - 07:00
     2020-05-03 18:16:21   associatedWith  myASControl
     2020-04-24 21:32:18   cloud           enabled(connected)
     2020-04-25 07:45:39   config          rc= [channel r]
     2020-04-24 21:32:18   firmware        v1.6.0
     2020-05-02 23:14:29   last_dir        up
     2020-05-03 19:02:31   network         connected to 10.0.0.212
     2020-05-03 08:18:40   pct             100
     2020-05-03 08:18:40   position        open
     2020-05-03 18:37:39   power           0
     2020-05-03 19:02:33   state           stopped
     2020-04-24 21:34:18   stop_reason     normal
Attributes:
   ASC        2
   ASC_Adv    on
   ASC_AutoAstroModeEvening ASTRONOMIC
   ASC_AutoAstroModeMorning ASTRONOMIC
   ASC_BlockingTime_afterManual 1200
   ASC_BlockingTime_beforDayOpen 3600
   ASC_BlockingTime_beforNightClose 3600
   ASC_BrightnessSensor SB.Dach:brightness
   ASC_Closed_Pos 0
   ASC_Down   astro
   ASC_DriveUpMaxDuration 20
   ASC_Drive_Delay 0
   ASC_Mode_Down always
   ASC_Mode_Up always
   ASC_Open_Pos 100
   ASC_Partymode off
   ASC_Pos_Reading pct
   ASC_PrivacyUpValue_beforeDayOpen 895
   ASC_PrivacyUp_Pos 20
   ASC_Shading_InOutAzimuth 140:290
   ASC_Shading_MinMax_Elevation 20:100
   ASC_Shading_Min_OutsideTemperature 10
   ASC_Shading_Mode always
   ASC_Shading_Pos 30
   ASC_Shading_StateChange_SunnyCloudy 50000:30000
   ASC_Shading_WaitingPeriod 300
   ASC_Time_Down_Early 16:30
   ASC_Time_Down_Late 21:30
   ASC_Time_Up_Early 7:15
   ASC_Time_Up_Late 8:00
   ASC_Time_Up_WE_Holiday 9:00
   ASC_Up     astro
   alias      Rol.EG_SZ1
   cmdIcon    open:fts_shutter_up closed:fts_shutter_down stop:fts_shutter_manual
   devStateIcon open:fts_shutter_10:closed closed:fts_shutter_100:open half:fts_shutter_50:closed drive-up:fts_shutter_up@red:stop drive-down:fts_shutter_down@red:stop pct-100:fts_shutter_100:open pct-90:fts_shutter_80:closed pct-80:fts_shutter_80:closed pct-70:fts_shutter_70:closed pct-60:fts_shutter_60:closed pct-50:fts_shutter_50:closed pct-40:fts_shutter_40:open pct-30:fts_shutter_30:open pct-20:fts_shutter_20:open pct-10:fts_shutter_10:open pct-0:fts_shutter_10:closed
   event-on-change-reading state
   group      Rolladen
   icon       fts_shutter_automatic
   mode       roller
   model      shelly2.5
   room       Haus
   userattr   ASC_Adv:on,off ASC_Antifreeze:off,soft,hard,am,pm ASC_Antifreeze_Pos:5,10,15,20,25,30,35,40,45,50,55,60,65,70,75,80,85,90,95,100 ASC_AutoAstroModeEvening:REAL,CIVIL,NAUTIC,ASTRONOMIC,HORIZON ASC_AutoAstroModeEveningHorizon:-9,-8,-7,-6,-5,-4,-3,-2,-1,0,1,2,3,4,5,6,7,8,9 ASC_AutoAstroModeMorning:REAL,CIVIL,NAUTIC,ASTRONOMIC,HORIZON ASC_AutoAstroModeMorningHorizon:-9,-8,-7,-6,-5,-4,-3,-2,-1,0,1,2,3,4,5,6,7,8,9 ASC_BlockingTime_afterManual ASC_BlockingTime_beforDayOpen ASC_BlockingTime_beforNightClose ASC_BrightnessSensor ASC_Closed_Pos:0,10,20,30,40,50,60,70,80,90,100 ASC_ComfortOpen_Pos:0,10,20,30,40,50,60,70,80,90,100 ASC_Down:time,astro,brightness,roommate ASC_DriveUpMaxDuration ASC_Drive_Delay ASC_Drive_DelayStart ASC_ExternalTrigger ASC_GuestRoom:on,off ASC_LockOut:soft,hard,off ASC_LockOut_Cmd:inhibit,blocked,protection ASC_Mode_Down:absent,always,off,home ASC_Mode_Up:absent,always,off,home ASC_Open_Pos:0,10,20,30,40,50,60,70,80,90,100 ASC_Partymode:on,off ASC_Pos_Reading ASC_PrivacyDownValue_beforeNightClose ASC_PrivacyDown_Pos ASC_PrivacyUpValue_beforeDayOpen ASC_PrivacyUp_Pos ASC_RainProtection:on,off ASC_Roommate_Device ASC_Roommate_Reading ASC_Self_Defense_AbsentDelay ASC_Self_Defense_Mode:absent,gone,off ASC_Shading_InOutAzimuth ASC_Shading_MinMax_Elevation ASC_Shading_Min_OutsideTemperature ASC_Shading_Mode:absent,always,off,home ASC_Shading_Pos:10,20,30,40,50,60,70,80,90,100 ASC_Shading_StateChange_SunnyCloudy ASC_Shading_WaitingPeriod ASC_Shutter_IdleDetection ASC_ShuttersPlace:window,terrace ASC_Sleep_Pos:0,10,20,30,40,50,60,70,80,90,100 ASC_TempSensor ASC_Time_Down_Early ASC_Time_Down_Late ASC_Time_Up_Early ASC_Time_Up_Late ASC_Time_Up_WE_Holiday ASC_Up:time,astro,brightness,roommate ASC_Ventilate_Pos:10,20,30,40,50,60,70,80,90,100 ASC_Ventilate_Window_Open:on,off ASC_WiggleValue ASC_WindParameters ASC_WindProtection:on,off ASC_WindowRec ASC_WindowRec_PosAfterDayClosed:open,lastManual ASC_WindowRec_subType:twostate,threestate
   webCmd     open:closed:stop:pct

das steht jetzt im State vom ASC Device:
Code Auswählen
STATE
please set attribute ASC with value 1 or 2 in all auto controlled shutter devices and then execute 'set DEVICENAME scanForShutters'

CoolTux

#1706
03 Mai 2020, 19:32:14
Du musst das event-on-change-reading löschen im ASC Device. Und das set muss natürlich korrekt mit Namen des ASC Devices angegeben werden.

set ASC DEVICENAME createNewNotifyDev. Mach es am besten direkt in der Detailansicht vom ASC Device im FHEMWEB
Du musst nicht wissen wie es geht! Du musst nur wissen wo es steht, wie es geht.
Support me to buy new test hardware for development: https://www.paypal.com/paypalme/MOldenburg
My FHEM Git: https://git.cooltux.net/FHEM/
Das TuxNet Wiki:
https://www.cooltux.net

Dreggwatz

#1707
03 Mai 2020, 20:12:32
 ::)
{ ascAPIget('Brightness','Rol.EG_SZ2') } gibt jetzt den gleichen Wert aus dem SB.Dach device. Würde ja schon mal passen.
Sonne ist jetzt weg, schaue morgen mal ob sich nun was tut. Danke Dir schon mal!  8)

Dreggwatz

#1708
03 Mai 2020, 20:23:19
Der Helligkeitswert aus der LOG stimmt aber mit dem aus dem device:
Code Auswählen
ASC_DEBUG!!! 2020.05. 3 20:19:20 - FnIsDay: Rol.EG_SZ1 Allgemein: 1

ASC_DEBUG!!! 2020.05. 3 20:19:20 - FnIsDay: Rol.EG_SZ1 getDownBrightness: 1 Brightness: 388.98 BrightnessMin: 500 Sunset: 0

ASC_DEBUG!!! 2020.05. 3 20:19:20 - FnIsDay: Rol.EG_SZ1 getUpBrightness: 1 Brightness: 388.98 BrightnessMax: 800 Sunrise: 0

ASC_DEBUG!!! 2020.05. 3 20:19:20 - FnIsDay: Rol.EG_SZ2 Allgemein: 1

ASC_DEBUG!!! 2020.05. 3 20:19:20 - FnIsDay: Rol.EG_SZ2 getDownBrightness: 1 Brightness: 388.98 BrightnessMin: 500 Sunset: 0

ASC_DEBUG!!! 2020.05. 3 20:19:20 - FnIsDay: Rol.EG_SZ2 getUpBrightness: 1 Brightness: 388.98 BrightnessMax: 800 Sunrise: 0

CoolTux

#1709
03 Mai 2020, 20:41:08
Passt jetzt
Du musst nicht wissen wie es geht! Du musst nur wissen wo es steht, wie es geht.
Support me to buy new test hardware for development: https://www.paypal.com/paypalme/MOldenburg
My FHEM Git: https://git.cooltux.net/FHEM/
Das TuxNet Wiki:
https://www.cooltux.net
Drucken
Nach oben Seiten 1 ... 112 113 114 115 116 ... 148
Benutzer-Aktionen